Volvo 240 Wagon 4D buyer's guide
Volvo 240 Wagon 4D -- the model's own buyer's guide: variants, values and what to check.
Years listed: 1976-1993 ยท Series: 240/260
Overview and history
The Volvo 240 is the car that turned Volvo from a sturdy Swedish also-ran into a byword for durability itself. Launched in the autumn of 1974 as a 1975 model and built, with remarkably little fundamental change, until May 1993, it is less a single model than a nineteen-year argument that a car should be safe, repairable and honest above all else. Something like 2.86 million 240- and 260-series cars were built, and an implausible number are still in daily service โ which is why you are reading a buying guide for a car whose youngest example is now over three decades old.
The 240 was an evolution, not a revolution. Underneath sits the architecture of the 140 series it replaced: a unitary steel body, MacPherson struts at the front, a live rear axle on coil springs located by trailing arms and a Panhard rod, rack-and-pinion steering and disc brakes all round. What Volvo changed for 1974 was everything the buyer could see and everything that mattered in a crash: a new nose with big impact-absorbing bumpers for the American market, and a body engineered around a rigid passenger cell, front and rear crumple zones, a collapsible steering column and three-point belts as standard thinking rather than optional virtue. The US government bought 24 of them in 1976 as an experimental safety fleet, and the 240 became the reference car for American crash standards.
Naming needs one paragraph of untangling, because Volvo changed its mind mid-stream. At launch the last digit told you the doors: 242 was the two-door sedan, 244 the four-door sedan and 245 the five-door wagon, while the six-cylinder cars were the 262, 264 and 265; the second digit told you the engine, 4 or 6. Trim was DL (the base car), GL and GLE. From the 1983 model year Volvo dropped the third digit in America and simply called everything a 240, with DL, GL, GLE, GLT and Turbo as designations. A 1986 car badged "240 DL" and a 1979 car badged "244 DL" are the same idea separated by a badge policy. This guide covers the four-cylinder 240 across all of it; the 260 gets its own discussion in the engines section.
Three broad eras organise everything else in this guide. The early cars (1975โ80) are the simplest: carburettors on some markets, Bosch K-Jetronic continuous injection on most American cars, the B21 2.1-litre engine, big "commando" bumpers on American cars, and the charming, upright early dashboard. The middle cars (1981โ85) bring the Turbo โ the car that proved a Volvo wagon could embarrass sports sedans โ along with the B23 engine, a facelifted nose and the first electronic LH-Jetronic injection. The late cars (1986โ93) are the ones most buyers actually find: a second, smoother facelift, the low-friction B230 engine, LH 2.4 management with self-diagnostics from 1989, anti-lock brakes standardising, a driver's airbag on American cars from 1990, and build quality many owners consider the peak of the line. The last cars of all, the 1993 240 Classic, were a numbered limited edition of 1,600 that closed the run.
Our own listings pool is a fair picture of the surviving American market. We track 35 cars spanning 1976 to 1993, and the weight sits where you would expect: 22 of the 35 are 1990โ93 cars, wagons outnumber sedans, white is the most common colour by a wide margin, and roughly two-thirds are automatics. The early cars are the rarities โ a single 1976 and a single 1979 in the pool โ because they were used up as family transport in the salt states, while the late cars were bought by people who already knew the 240 was the last of its kind.
What you are buying, in any year, is the same set of priorities: a body engineered to protect you, an engine engineered to be rebuilt rather than replaced, and an interior engineered for Swedish winters and twenty-year service. No 240 is fast in standard form and none is luxurious in the German sense. Judge one the way its makers judged it: is the shell sound, does everything still work, and has it been maintained like the long-term proposition it was designed to be?


The models
Every 240 is a sedan or a wagon on the same 104-inch (2,640 mm) wheelbase; there was never a factory convertible, and the one coachbuilt coupรฉ, the Bertone 262C, belongs to the 260 family. The buying decisions that matter are body style, era and engine, in roughly that order, because Volvo's trim ladder mostly added equipment rather than character. Production figures below are the factory's series totals where they are genuinely documented; Volvo did not publish clean splits by trim, and the table says so rather than inventing them.
| Model | Years | Engine | Output | Built | Character |
|---|---|---|---|---|---|
| 242 (two-door sedan) | 1975โ1984 | B20, then B21/B23/B230 2.1โ2.3 four | 82โ114 hp | 242,621 | The lightest shell; GT and Turbo versions are the sporting 240s |
| 244 (four-door sedan) | 1975โ1993 | B21/B23/B230 four, carb or injected | 82โ116 hp | 1,483,399 | The default 240; the volume car in every market |
| 245 (five-door wagon) | 1975โ1993 | B21/B23/B230 four, carb or injected | 82โ116 hp | 959,151 | The wagon that defined the type; the most wanted body today |
| 240 Turbo (244/245 Turbo, GLT Turbo) | 1981โ1985 | B21FT/B21ET 2.1 turbo four | 127โ155 hp | Not separated in period reporting | The performance 240; intercooled cars from mid-1984 are the pick |
| 260 (262/264/265, incl. 262C) | 1975โ1985 | B27/B28 2.7โ2.8 PRV V6 | 125โ155 hp | About 165,000 all bodies | The six-cylinder flagship; smoother, thirstier, more fragile |
| 240 Diesel (244/245 D) | 1979โ1985 | D20 2.0 five / D24 2.4 six diesel | 68โ82 hp | Not separated in period reporting | Volkswagen-sourced diesels; slow, economical, now very rare in the US |
| 240 Classic | 1993 | B230F 2.3 four | 114 hp | 1,600 | The numbered farewell edition; trim and badges over a late GL |
(Outputs are period figures for the principal American and European versions; the carburettor cars sold in some markets sat at the bottom of each range, the intercooled Turbo at the top. The three body totals are the factory's own and sum to the 2,685,171 four-cylinder cars usually quoted for the 240 proper, before the 260s are added.)
The two-door (242). The lightest and stiffest shell, and the basis of the cars enthusiasts chase: the 1979โ80 242 GT, with its uprated suspension and spoilers, and the 242 Turbo that headlined the performance range. Volvo dropped the two-door after 1984, judging โ correctly, commercially โ that 240 buyers wanted four doors or a wagon. A sound 242 is now the hardest body to find, and a genuine GT or two-door Turbo is the closest thing the range has to a blue-chip car.
The sedan (244, later just 240 sedan). The core of the range and the default recommendation for a buyer who wants the 240 experience at the keenest price. Sedans were the fleet, family and first-owner cars; they led harder lives than the mythology suggests, but they are also the cheapest way into a late, well-kept car, because the market's money chases wagons. Everything said in this guide about engines, rust and inspection applies to the sedan first.
The wagon (245, later just 240 wagon). The car that made the 240 immortal. The load bay is vast, flat and square โ the shape is the function โ with an optional rear-facing third-row seat that folded into the floor and made it a seven-seater years before that was fashionable. Wagons were bought by families, antiques dealers and dog owners, used hard, and kept forever; the best late wagons are the most contested cars in this whole guide. A car that has spent twenty years hauling building materials has lived a different life from a suburban school-run car, and the rear suspension and load floor will tell you which.
The Turbo (1981โ85). Volvo turbocharged the B21 to make the GLT Turbo sedan and wagon, sold as the 240 Turbo in its last years. Non-intercooled cars made about 127 hp in American tune; the intercooler kit, offered first as a dealer option and standardised during 1984 alongside the Turbo+ boost control on some markets, lifted European B21ET cars to 155 hp. These are real performance cars by the standards of 1982 โ and real projects by the standards of now, because turbo cars were driven hard, modified often and maintained unevenly. The engines section covers what to verify.
The 260 and the diesels. The six-cylinder 260 shared the shell with a plusher nose and the PRV V6; the Bertone-built 262C coupรฉ (6,622 built, 1978โ81) is its glamorous outlier. The V6 is smoother than the four and considerably more delicate, and it is covered honestly below. The diesels used Volkswagen's D20 and D24 engines, sold in meaningful numbers in Europe, trickled into America around 1981โ84, and have almost vanished โ a survivor is a curiosity, bought for economy-era charm rather than pace.
Trim, briefly. DL meant the working car: vinyl or hard-wearing cloth and fewer toys. GL added better trim and plusher seats; GLE added equipment again, and GLT was the sporting trim โ uprated suspension and, confusingly, sometimes a naturally aspirated engine with the Turbo's chassis, sometimes the Turbo itself. Badge archaeology is a trap on a forty-year-old car: equipment gets swapped and badges get changed, and the VIN plate and engine number settle what a car actually is. Buy the car in front of you, not the letters on its tailgate.


Engines and gearboxes
Nineteen years produced one engine family that matters, a six-cylinder guest appearance, and a bought-in diesel. The four-cylinder "Redblock" โ so called for its red-painted cast-iron block โ is the engine in the overwhelming majority of survivors and the reason the 240 has its reputation: an overhead-cam, crossflow-head four with a belt-driven camshaft, five main bearings and a bottom end so over-engineered that the same basic architecture later took factory turbocharging and, in enthusiast hands, several times its original output. Learn the Redblock's generations and you have learned the 240.
The Redblock fours: B20, B21, B23 and B230
B20 (1975โ76, some markets to later). The earliest 240s carried over the 140's pushrod B20 2.0-litre, carburettor or injected depending on market. It is a simple, torquey, agricultural engine, but it belongs to the oldest and usually rustiest cars, and in America it was gone after 1976. Judge a B20 car as an early-car purchase, not an engine purchase.
B21 (1975โ84). The first true Redblock: 2,127 cc, alloy crossflow head, single overhead cam driven by a rubber timing belt โ still a novelty in 1974 โ and, in American form, Bosch K-Jetronic continuous mechanical injection as the B21F. European cars also came with carburettors (B21A) and, from 1981, the turbocharged versions below. The B21 is a strong engine with one era-specific weakness: the K-Jetronic system around it, covered below. Outputs ran from about 98 hp for the early American B21F, strangled by first-generation emissions tuning, to 114 hp in later and European tune.
B23 (1983โ84) and B230 (1985โ93). The 2,316 cc enlargement arrived as the B23, then was comprehensively reworked into the B230 for 1985: lighter pistons, smaller bearing journals and lower-friction internals โ the "low-friction" engine. Very early B230s (1985, and some 1986 cars) have a reputation for weaker connecting rods and smaller main bearings than the 1989-onward revision, which matters to turbo-swappers and barely at all to a buyer of a standard car used as intended. The B230F that powers almost every late American car makes 114 hp, pulls from low revs, and is as close to unburstable as a production engine gets: 300,000 miles on the original bottom end is unremarkable in a maintained car, and the things that stop a B230 are almost never the engine itself โ they are the fuel system, the ignition components and the cooling system around it.
All Redblocks share the service facts that decide an inspection. The timing belt is a service item โ roughly every 50,000 miles is the prudent interval on a car of unknown history โ and the Redblock is a non-interference design in standard form, so a snapped belt strands you rather than destroying the engine; budget a belt, tensioner and front seals as an early job on any car without a dated invoice (a $400โ800 job at a shop, less in parts for a home mechanic). Valve clearances are set by shims and rarely move. The flame trap โ Volvo's crankcase ventilation strainer in the breather box on the side of the block โ clogs with age and neglect, and a clogged flame trap pressurises the crankcase and pushes oil out of every seal: the rear main, the cam seals, the filler cap. Half the "oil-leaking Volvo" stories in the classifieds are a $15 flame trap and breather service that nobody did, and a car whose engine is wet with oil but whose breather is blocked is a negotiation point, not a walk-away.
The Turbo: B21FT and B21ET (1981โ85). Volvo added a Garrett turbocharger, a strengthened bottom end, a sodium-filled exhaust valve set and an oil cooler to the B21 and created the fastest production Volvo of its day. American B21FT cars ran K-Jetronic with Lambda control and about 127 hp; European B21ET cars, without the American emissions package, made 155 hp, and the intercooler โ a dealer-fit kit at first, then productionised during 1984 โ is the single most desirable option on any Turbo. Turbo engines live harder lives: check for oil smoke on start-up and under boost (turbo seals), listen for bearing whine from the turbo itself, and verify the car has not been turned up by a previous owner with a bleed valve and optimism. A turbocharger rebuild or replacement is a $900โ1,800 conversation; a documented, standard, intercooled car is the one to pay for.
The six and the diesels: B27/B28 and D20/D24
The PRV V6 (260, 1975โ85). The 260's 2.7-litre (later 2.8) all-alloy V6 was the joint Peugeot-Renault-Volvo engine, and it is the one engine in this guide you buy with your eyes open. In its favour: it is smooth, quiet and torquey, and the 262C and 264 GLE are genuinely plush cars. Against it: the early B27's camshafts and rocker gear wear if oil changes were stretched, the engine is intolerant of overheating, and parts and expertise are thinner than for the Redblock. The later B28 is the better engine. A 260 with a documented oil-change history and a cool, quiet top end is a fine car; a neglected one is an engine-out bill that can exceed the car's value, which is why the market prices good fours above average sixes.
The diesels (1979โ85). Volvo bought its diesels from Volkswagen: the 2.0-litre five-cylinder D20 and, far more commonly, the 2.4-litre six-cylinder D24, making 68โ82 hp. They are indirect-injection engines of the old school, with a timing belt whose failure โ unlike the petrol Redblock's โ does destroy the engine, because the diesel is an interference design. Head cracking on overheated D24s is the known weakness. Almost no American survivors remain; buy one as a preserved oddity, not as cheap transport.
Fuel and ignition systems: K-Jetronic, LH-Jetronic and the rest
More 240 buying mistakes are fuel-system mistakes than engine mistakes, so learn the systems by year. K-Jetronic (Bosch CIS) serves most cars to about 1982 and all Turbos: a purely mechanical continuous-injection system metered by an airflow plate and a fuel distributor, with a warm-up regulator shaping the mixture as the engine warms. It is reliable when used and infuriating when left sitting: varnish in the fuel distributor, a lazy warm-up regulator, and perished vacuum hoses are the standard faults. The diagnostic tell is a car that starts poorly hot or hunts at idle. A fuel-distributor rebuild is specialist work at roughly $600โ1,200; budget for an accumulator, filters and both fuel pumps on any K-Jet car that has stood.
LH-Jetronic arrived in stages โ LH 2.0 on some 1982โ84 cars, LH 2.2 for most 1985โ88 cars, LH 2.4 from 1989 to the end โ and replaced the airflow plate with a hot-wire air mass meter and electronic injectors. It is the system you want for a car you intend to use: better starting, better economy, and on LH 2.4 a diagnostic socket under the bonnet that flashes fault codes with no tools at all. Its known faults are specific and testable. The air mass meter fails and causes stalling and rich running โ a rebuilt unit is a $200โ450 part, and unplugging the meter on a suspect car is the classic roadside test: if it idles better unplugged, on the ECU's limp map, the meter is condemned. The idle air control valve gums up and causes a wandering idle; cleaning it is free and precedes any parts purchase. The engine temperature sensor drifts and tells the ECU the engine is cold forever, giving a rich, thirsty car โ a cheap sensor and a resistance check settle it. Ignition on late cars is EZK electronic with a crank position sensor whose insulation crumbles with age; a late car that cuts out hot and restarts cold has usually named its own fault.
Carburettor cars โ the B21A and B23A sold outside America โ are the simplest of all. Their faults are the period faults: worn throttle spindles sucking air, tired diaphragms, automatic chokes that stick. A rebuild kit is cheap; a car that idles at 1,500 rpm hot is telling you about spindle wear, not adjustment.
Gearboxes
Manuals. The four-speed M45 is the early standard box; the M46 adds a Laycock electric overdrive on fourth โ effectively a fifth gear โ engaged by a switch on the gear knob or dash; the M47, from the early 1980s, is a true five-speed and the most common late manual. All are strong, slightly deliberate boxes whose synchromesh, especially on second, wears with age and abuse. The M46's overdrive is its own subsystem: it engages only in fourth, depends on a relay, a solenoid and correct oil level shared with the gearbox, and its classic failure โ overdrive that drops out hot or never engages โ is electrical or oil-level nine times out of ten, a $40โ250 fix, rather than the unit itself. Test it on the test drive at a steady 50 mph, in and out several times, hot. The M47's known quirk is a weak fifth-gear layout in early versions; listen for whine in fifth. Clutches are long-lived; a replacement is a $700โ1,200 shop job.
Automatics. Early cars used the three-speed Borg-Warner BW55; the four-speed Aisin-Warner AW70 (and the stronger AW71, fitted to turbos and some later cars) took over from the early 1980s and serves nearly every late car you will see. These are among the most durable automatics ever fitted to anything: fluid changes every 30,000 miles or so, clean changes in both directions, and no flare between gears is the whole test. The AW70's overdrive is again electric, controlled by a relay โ famously hidden behind the glovebox โ and a solenoid on the gearbox; an automatic that will not shift into fourth has usually blown the overdrive relay, a part that costs about $30 and takes minutes to change once you know where it hides, and sellers routinely discount cars for it. A box that flares, shudders or delays reverse engagement is a different matter: a rebuild runs $1,800โ3,000, so road-test from cold and walk away from a car whose seller insists it be warmed up before you arrive.


Problem areas
A 240 fails in predictable places, and almost none of them is the engine. Across the whole run the pattern is this: the shell rusts in a specific map of traps, the wiring of one particular era disintegrates by design, the suspension wears its rubber out on schedule, and the interior's expensive parts are the ones that require the dashboard to come out. Work through this section in order and you will know more about a specific car than most sellers do.
Rust: the map
The 240 was better rustproofed than most 1970s cars โ Volvo galvanised more of the shell as the years passed, and late cars are noticeably more resistant โ but no 240 is immune, and the rust follows the water and the road salt in a fixed order. Assume a northern or coastal car needs the full examination below; a lifelong dry-state car can be genuinely sound, which is why shell provenance matters more than any other single fact about a 240.
Rear wheel arches and the "butt cheeks." The first place to look, on every car. The rear arches trap mud behind the lip, and behind the rear wheels the lower rear quarter panels โ the spare-wheel well on one side and its mirror pressing on the other, known to every 240 owner as the butt cheeks โ rot from the inside out. Open the boot or the wagon's rear side compartments and look down into those wells: surface bubbling on the outside means established rust inside. Arch and quarter repair is panel work, roughly $800โ2,000 a side done properly with paint, and it is the most common structural bill on the car.
Sills and floor edges. The sills carry the jacking points and collect everything the front wheels throw up. Prod along the full length, especially at the ends where the drain slots block, and lift the carpets to check the floor pans where they meet the sills and under the front footwells, where a leaking windscreen or heater box drips. Perforated sills are a welding job at $600โ1,500 a side; floor pans are available as repair sections, but floor rust is a marker for the whole shell rather than an isolated defect.
The windscreen surround and the tailgate. The front windscreen frame rusts under the seal, invisibly until the screen comes out or the headlining stains; budget a screen-out repair if you see bubbling at the corners of the glass, because what shows is a fraction of what is there. Wagon tailgates rust along the bottom edge and around the window, and the wiring that passes into the tailgate โ for the wiper, heated window and number-plate lamps โ breaks inside its hinge looms, which is an electrical fault with a rusty accomplice. Sedan boot floors and the spare-wheel well rust from leaking rear-window and boot seals, exactly as on the wagons.
The rest of the map. Front wings behind the wheels, door bottoms where the drain holes block, the battery tray and the inner wing beneath it, the front crossmember, and โ on salt cars โ the fuel tank straps and rear spring seats. None of these alone writes a car off, but the pattern is cumulative: a car rusty in three places is rusty in six, and structural welding overtakes the value of an ordinary 240 faster than any other cost in this guide. Fresh, uniform underseal over everything, brake pipes included, is a cover-up until the seller proves otherwise.


The wiring harness: the 240's one designed-in failure
Between roughly 1980 and 1987, Volvo โ chasing environmental virtue โ used engine-bay wiring insulation that biodegrades. It does not merely perish: it crumbles to powder inside its own loom tape, leaving bare copper conductors touching each other and the engine, and the symptoms mimic everything else in this guide: random stalling, gauges lying, charging faults, injection faults that move from component to component, and in the worst cases melted looms and under-bonnet fires. The affected years centre on 1982โ87, with the worst reputation attaching to the mid-1980s cars; both the engine harness and, on some cars, the alternator and starter leads are involved.
The test is physical and takes two minutes. Find the harness where it passes along the front of the engine and under the intake manifold, and where it crosses near the alternator: flex the insulation and look for cracking, flaking and exposed copper. A car in the affected years with a documented replacement harness โ new old stock, a quality reproduction, or a carefully rebuilt loom โ has had its single biggest liability removed, and that paperwork is worth a real premium. A car with original crumbling insulation is a car whose price must carry a harness replacement: a reproduction harness is a $400โ700 part, with a day's labour to fit, $900โ1,600 all-in at a shop, and it is not optional work. This is the one place in this guide where a myth runs the other way: the biodegradable harness is not internet folklore, it is the first thing to check on a mid-1980s car, ahead of the injection system it so often impersonates.
Outside the harness years, electrics fail in the ordinary Volvo ways: at the connections. The fuse box uses the old European ceramic torpedo fuses whose ends corrode and make intermittent contact โ a fuse that looks whole can be open at its cap โ and cleaning the contacts and fitting fresh fuses cures a remarkable share of "electrical gremlins." Earth points corrode the same way. The alternator's brush pack and regulator are a single replaceable unit and a $40โ90 part; a charging light that glows dimly at idle is usually brushes, not the alternator. On late cars the crank position sensor lead is the one modern-style failure: heat-cracked insulation, intermittent cutting-out, and a cheap part buried at the back of the engine.
Suspension, steering and brakes
The 240's chassis is simple, strong and entirely dependent on rubber. The front struts wear their top mounts (a knock over bumps), ball joints and control-arm bushings; the steering rack boots split and let grit into the rack, which then leaks from its seals โ a rebuilt rack fitted runs roughly $700โ1,200, and power-steering fluid weeping from a boot is its announcement. At the rear, the live axle hangs on trailing arms whose large forward bushings are the single most-worn suspension part on the car: when they go, the axle steers the car from behind, the rear end clunks over bumps and wanders in crosswinds. A full rear bushing refresh with parts and labour runs $800โ1,600 and transforms a tired car more completely than any other single spend. Torque-rod and Panhard-rod bushings wear on the same schedule.
Springs sag, especially wagon rear springs that have carried loads, and shock absorbers are consumables owners forget for decades: a car that wallows and crashes over potholes is usually on its second set of dampers in thirty years. None of this is exotic โ every wear part is available, most of it cheaply, and a full suspension refresh is a known quantity at $1,500โ3,000 in parts and labour โ but add it honestly to the price of a car that needs it all.
Brakes are discs all round with a dual-circuit system of unusual sophistication for the era. The failure mode is not design but age: seized calipers (the rears especially), perished flexible hoses, rusted steel lines in salt states, and a handbrake working through small drum shoes inside the rear disc hat that is routinely seized or worn to nothing. A full hydraulic refresh โ calipers, hoses, pads, discs and fluid โ is $900โ1,800 at a shop and should be treated as recommissioning, not repair, on any car that has stood. Date-check the tyres, too: a car on ancient, cracked rubber will drive badly in ways that get blamed on the suspension.
Interior, heater and body fittings
The 240 interior is famously hard-wearing โ the vinyl and cloth outlast most cars' leather โ and its failures are specific. The dashboard top cracks in sun states, in splits around the speaker grille and defroster vents; uncracked dashboards are now a selling point, and covers hide the truth, so look at the edges. Seat foam and the seat diaphragm sag, leaving you sitting in the seat rather than on it; the driver's seat goes first, and a rebuild with new foam and webbing is $250โ500 a seat. Wagon headlinings sag and are a fiddly, half-day job to replace properly.
The heater is the interior's one big bill. Test the blower on every viewing, on every speed, whatever the weather. The blower motor lives at the centre of the dashboard, and Volvo's own book time runs to many hours because the dashboard comes out to reach it; at a shop, a blower motor replacement is a $900โ1,800 job on a part that costs $80โ150, and a squealing, slow or dead blower is therefore a four-figure negotiation point, not a quirk. The heater core itself leaks into the front footwells โ sweet smell, misting windscreen, damp carpets โ and is the same dashboard-out labour to replace. Heater control cables seize and the valve fails; those are cheap. It is the access that costs.
The rest is honest wear: window switches, central locking actuators that give up one door at a time, tailgate struts that no longer hold the gate up, and instrument clusters whose odometer gears crumble โ a very common failure, which is why so many 240 odometers stopped decades ago and why a claimed mileage without paperwork is a story, not a fact. On a car famous for 300,000-mile engines, the difference between a 140,000-mile car and a 240,000-mile car matters less than the maintenance record, and the odometer alone cannot tell you which you are looking at. Judge condition and history; let the number on the dial be a hint.

How to inspect one
Allow an hour, bring a torch, a magnet wrapped in cloth, and a screwdriver you may prod with if the seller agrees. A 240 rewards method: the expensive faults are all findable in a set order, and the car's honesty is usually visible before you turn the key.
- Paperwork and identity first. Match the VIN on the title to the plate on the dashboard, visible through the windscreen, and to the stamped plate in the engine bay. Read the service history for the three invoices that price a 240: a dated timing belt, a replacement wiring harness on any 1980โ87 car, and evidence of flame-trap and breather servicing. A thick folder on a 240 is not a bonus; it is a substantial part of what you are buying.
- Cold start. Insist the engine is stone cold when you arrive. A Redblock should fire at once and settle to a steady idle. Blue smoke on start-up that clears points to valve stem seals; smoke that stays is wear. Listen for a rattle from the front of the engine (a tired belt tensioner or water pump) and watch the oil light go straight out.
- The oil and breather test. Pull the dipstick: the oil should sit at its mark and not smell of fuel. Then, with the engine idling, rest the loosened oil filler cap on the filler neck โ on a healthy engine it sits and trembles; a clogged flame trap pressurises the crankcase and dances or blows the cap off, and an engine wet with oil at every seal is usually the same story told twice. This two-minute test from the engines section prices the car's maintenance history better than any other.
- The harness check, on 1980โ87 cars. Flex the engine-bay wiring where it crosses the front of the engine and passes the alternator, exactly as the problem areas section describes. Cracking insulation and visible copper end the discussion until the price reflects a replacement harness. Do not skip this step because the car runs well today; the harness fails by touching, not by warning.
- Rust: work the map from the back. Start at the rear arches and the wells behind the rear wheels โ open the boot or the wagon's rear compartments and look down into them โ then the sill ends and jacking points, then under the carpets in all four footwells, then the windscreen corners and the tailgate's bottom edge on a wagon. Prod with the screwdriver where the seller allows. Perforation in the rear quarters, sills or floors is structural money; agree the welding bill before you fall for the rest of the car.
- Underneath. Get the car on a lift if it passes you, or at minimum on ramps with a torch. You are reading the front crossmember, the floor seams, the brake and fuel lines, the fuel tank straps, the rear spring seats and the state of the underseal โ patchy and honest is factory, a fresh uniform coat over everything is a question. Check the trailing-arm bushings for perished, offset rubber while you are there.
- Suspension and steering by hand. Bounce each corner: one return and settle is a live damper, continued bouncing is not. Rock each front wheel top-to-bottom and side-to-side for bearing and ball-joint play. Look through the steering rack boots for fluid. At the rear, any visible perishing in the big trailing-arm bushings is a priced job, not a note.
- The test drive. Fifteen minutes, mixed roads, a fast stretch. A manual car should take second gear without a crunch from cold and pull cleanly; on an M46, engage and disengage the overdrive repeatedly at a steady speed, hot, and confirm it holds. An automatic should change cleanly in both directions with no flare, and it must find fourth: if it will not, suspect the overdrive relay from the gearboxes section before you suspect the gearbox. Brake firmly from speed โ straight, no judder, no pull โ and listen at full lock for power-steering groans and rack knocks.
- Heat and electrics, whatever the weather. Run the heater to full temperature and the blower on every speed: a dead or squealing blower is dashboard-out money, as the problem areas section sets out. Work every window, the central locking, the heated rear window, wipers and washers, and every light. On an LH 2.4 car (1989 onward), ask whether the diagnostic socket has shown codes; a seller who knows what that means has usually maintained the car.
- Stance and shutlines. Stand back and look at the car level, from each corner. A 240 should sit square; a wagon sagging at the rear is springs or a life of loads, a nose-down car is front springs, and a lean to one side is a spring or a strut top. Run the magnet over the rear arches, sill ends and door bottoms โ filler over rust announces itself, and on a 240 filler is always a question about what is underneath, not a finish defect.
- Interior last, from the driver's seat. Sit where the owner sat: feel for a sagging base and broken webbing, look under the seats and mats for the damp that means heater core or screen leaks, check the dashboard top at its edges for cracks, and try the odometer against the paperwork โ a stopped odometer is common and forgivable, a stopped odometer presented as low mileage is neither.
- Decide on the shell, then the systems. Add up what you have found in the order this guide prices it: structural rust first, harness second on a mid-eighties car, heater and blower third, then suspension rubber, then the mechanical consumables. A 240 whose shell and harness are right can absorb every other bill at a planned price. The reverse is never true.


Values
The build beneath this guide carries the current listings and recorded-sale figures for the 240, refreshed as the market moves, and that block is where you read today's prices. What this section gives you is how to read them: what drives the spread between the cheapest and the dearest 240, and where asking prices part company with the money that actually changes hands.
The 240 market is a condition market more than a rarity market. Volvo built millions, so scarcity โ the genuine 242 GT and two-door Turbo, the intercooled Turbo, the 1993 Classic โ sits at the top as a distinct tier, while the great mass of cars is priced by shell condition, body style and evidence of maintenance, in that order. The spread inside a single model year is routinely wider than the spread between model years: a rust-free, documented late wagon and a rusty, undocumented one carrying the same year on the title are barely the same commodity, and any median figure blends the two. Read the market block by splitting it in your head into those two cars before you treat a median as a valuation.
Body style is the steadiest premium. Wagons carry it over sedans of the same year and condition, because the wagon is the car people picture and the car people use; two-doors carry it over both when the shell is right, because they are the hardest body to find unrotted. Turbos carry a premium that is real but conditional: the market pays for documented, standard, preferably intercooled cars, and discounts modified or smoky ones back to ordinary money, because a tired turbo engine costs ordinary money plus a turbo. The 1993 Classic trades a little above a comparable late GL on its badges and numbered plaque โ a collector's premium on a car that is mechanically a standard late 240, so buy the condition and let the plaque be a bonus. Diesels and six-cylinder 260s sit in their own small pools where the right buyer pays fairly and everyone else passes; allow time, rather than discount, to be the cost of selling one.
Asking prices and achieved prices diverge in a characteristic place: the optimistic private asking price, set by an owner who has priced the model's cult mythology instead of the shell. Cars with structural rust, a crumbling harness or a dead blower are routinely advertised at sorted-car money, and they sit. Auction results and recorded sales price the car in front of the room, which is why achieved figures tend to sit below the asking medians for ordinary cars and at or above them for exceptional ones โ a truly sound late wagon or a genuine Turbo makes its money in public, because several buyers can see the same shell at once. Use the block's achieved figures to value an ordinary car, and treat any car priced between the two as a negotiation about the inspection findings in this guide.
The project-versus-driver gap is wide and honest. A running, structurally sound car that needs the suspension, brakes and breather work of the problem areas section is the market's sweet spot: the work is all priced and none of it is open-ended. A non-running car, or one with perforation in the rear quarters and sills, is priced as a shell and a parts source unless it is a rare variant โ because welding is the one bill that grows as it is uncovered, the gap between a project and a driver is not a discount you capture, it is a risk you buy. Geography moves money too: shipping a sound dry-state car into the salt states is very often cheaper than welding a rusty local one.
Parts and ownership
The 240 is one of the best-supported cars of its era, for a structural reason: Volvo built the same car for nineteen years, kept faith with owners by supplying parts long after production ended, and the enthusiast trade โ IPD in the United States, Skandix and a deep bench of European specialists โ has filled every gap the factory left. Almost nothing on a four-cylinder 240 is unobtainable; the ownership skill is knowing which parts are cheap, which are dear, and which jobs cost labour rather than parts.
Easy and cheap: every service item โ filters, plugs, belts including the timing belt kit, hoses, thermostats โ plus brake discs, pads, calipers and flex hoses, water pumps, alternators and their brush packs, flame traps and breather parts, suspension bushings, ball joints, dampers and springs, clutch kits, engine mounts, exhaust systems in standard form, and the overdrive relays and solenoids whose failure imitates gearbox death. Most of it is order-today, fit-this-weekend, at prices close to ordinary-car money, and the Redblock's engine bay is roomy enough that a competent home mechanic can do nearly all of it.
Harder and dearer: the biodegradable-era wiring harness (a reproduction part, as the problem areas section sets out), K-Jetronic fuel distributors and warm-up regulators for the early cars, turbochargers and intercooler pipework for the Turbo, air mass meters for LH cars (rebuilt units are the sensible buy), heater blower motors and cores โ cheap parts behind expensive labour โ uncracked dashboards, good tailgates, the PRV V6's engine internals for the 260, and diesel-specific parts for the D24. None of it is impossible; all of it rewards buying a car that does not need it yet.
Running costs. A sorted 240 is a realistic daily classic. Expect fuel consumption in the mid-twenties miles per gallon on a run for an injected four, less around town and notably less for a Turbo or a V6. Insurance sits in line with other cars of the value, tyres are in inexpensive sizes, and any good independent Volvo or European specialist can maintain the car โ though a specialist who knows the flame trap from the fuel distributor is worth seeking out for diagnosis. The budget line that catches new owners is the first year: catching up deferred maintenance on a running car โ belt, breather service, brake hydraulics, suspension rubber, fluids throughout โ honestly runs into the low thousands before you improve anything, and recommissioning a car that has stood for years costs more, because standing is what kills K-Jetronic fuel systems, brake calipers and tyres. Buy a car in regular use over a sleeping bargain at the same money, every time.
Ownership has one more dimension: the 240 is supported by one of the deepest knowledge communities of any classic car. Factory service literature is thorough and widely reproduced, the diagnostic codes on late cars are published and readable with basic tools, and every fault in this guide has been diagnosed in public, with photographs, by owners who fixed it in a driveway. For a buyer keeping a car for a decade, that support is worth as much as the parts supply.

Which one to buy
- The all-rounder: a 1990โ93 240 wagon, automatic or manual. The final development of the car: revised B230, LH 2.4 diagnostics, the best rust protection of the run and the deepest supply of good survivors. If you want one 240 to use daily and keep indefinitely, this is it.
- The value buy: a late sedan. The same shell, engine and running gear as the wagon without the wagon premium. A documented 1989โ93 sedan is the cheapest route into a genuinely sorted 240, and the boot is bigger than the market's indifference suggests.
- The driver's car: the Turbo, intercooled. A 1984โ85 Turbo โ or an earlier car with the intercooler kit documented โ is the 240 with genuine pace. Buy on turbo health and originality, and walk away from turned-up, smoky examples whatever the discount.
- The enthusiast's car: a 242. The two-door, in GT or Turbo form if you can find one honestly, in any form if the shell is right. The hardest body to replace and the one the market is slowly re-rating.
- The classic choice: an early car, 1975โ80, from a dry state. The purest shape and the simplest specification, bought for charm and preservation rather than daily duty โ and only with a shell that has never seen salt, because early rust protection is the weakest of the run.
- The farewell: a 1993 Classic. A numbered late car in sedan or wagon form. Buy the condition first and the edition second; its premium is real but modest, and a tired Classic is worth less than a sorted ordinary car.
And the rule that overrides all of the above: buy the least rusty shell you can find, with the maintenance history to prove it has been kept, in the body style you actually want. Engines, gearboxes, blower motors and suspension rubber are all fixable at prices this guide has named. A rotten shell, a crumbling harness nobody replaced, and a history nobody kept are the three things about a 240 that money cannot make original again.
