Home / Buyer's guides / TR6

Triumph TR6 buyer's guide

Triumph TR6 -- the model's own buyer's guide: variants, values and what to check.

Years listed: 1968-1976 ยท Series: TR

Overview and history

The Triumph TR6 is the last of the traditional TRs: a separate-chassis, two-seat British roadster with a big pushrod straight six in front, independent rear suspension behind, and a shape that still reads as the definitive small sports car half a century later. It was launched in January 1969 and built at Canley, Coventry, until July 1976. More than 90,000 were made, and the overwhelming majority โ€” roughly nine cars in ten โ€” were exported, most of them to the United States. That shapes everything about buying one today: the surviving market is deepest in America, almost every car you will shop for is a left-hand-drive US-market carburettor car, and the injected home-market cars are the rare exception here, not the rule.

The TR6 was not a new car underneath. Triumph took the TR5 and TR250 of 1967โ€“68 โ€” a TR4A chassis and body with the 2.5-litre six from the Triumph 2000 saloon range โ€” and sent the Michelotti-styled shell to Karmann for a restyle. Karmann squared off the nose and tail and left the centre section, doors and windscreen frame as TR4 carry-overs. The result looked new, cost Triumph very little to develop, and sold at a healthy margin against the MGB for seven and a half years. Its replacement, the unitary TR7, shares nothing with it but the badge โ€” which is precisely why the TR6 has become the TR most buyers actually want.

Two specifications divide the range, and you must know which one you are looking at before anything else about a car makes sense. Home-market and most European cars carry Lucas mechanical petrol injection โ€” the PI cars, commission numbers beginning CP for 1969โ€“72 and CR for 1973 on โ€” and a genuine 150 hp in early form. US-market cars carry twin Zenith-Stromberg carburettors instead, commission numbers beginning CC for 1969โ€“72 and CF for 1973โ€“76, and make roughly 104 hp in a softer tune that emissions equipment eroded further as the seventies wore on. The injected car is sharper, faster and considerably more valuable in Britain; the carburettor car is simpler, far more numerous in America, and the one this guide weights most heavily, because it is the one in the listings. Neither is the "wrong" TR6 โ€” they are different ownership propositions wearing the same body.

On Classic Listings as we write, we track 20 TR6s, all for sale and every one sourced from a Facebook Marketplace seller. The years skew late: 7 of the 20 are 1976 cars, the final year, and 5 are from 1974. One listing is dated 1968, which predates the January 1969 launch; production began in late 1968 for the 1969 model year, so an early car is possible, but a 1968 date can equally be a misdated car or a TR250 wearing the wrong year โ€” the commission number settles it. Of the cars that state a colour, red leads with 4. The pool clusters in New Jersey, North Carolina and Pennsylvania with 3 cars each โ€” a weighting that matters, because winter salt is this car's worst enemy and a car's home state is your first clue about its frame. One listing in the wider data claims an automatic gearbox. Treat any such claim as a listing error: Triumph never sold a TR6 with an automatic, in any market, at any point in the run.

What defines a TR6 as a purchase is the same split that defines every chassis-era TR, sharpened. The mechanicals are simple, strong and rebuildable: a long-stroke six, a four-speed gearbox with an optional Laycock overdrive, and a parts trade that can supply almost everything from a catalogue. The structure is the opposite proposition. The body is cosmetic panels bolted to a separate steel frame, both rust, and the frame rusts worst exactly where a listing photograph never looks โ€” at the rear trailing-arm mounts, the outriggers and the differential pins. A TR6 can present with glossy paint, start on the button and drive straight while its frame is perforated under the floors. Price the mechanics from the invoices and the tests, and price the car from underneath it. The survivors divide sharply between garaged, club-kept cars that are genuinely excellent and tired cars wearing a driver's price; telling the two apart โ€” from underneath, from cold, and from the paperwork, in that order โ€” is the whole skill this guide teaches.

A red 1976 Triumph TR6 from Edgewater, Florida
A red 1976 TR6 from Edgewater, Florida โ€” the final model year, and the commonest in our current pool, with 7 of the 20 cars. A 1976 US car is a CF-commission carburettor car with the heavy federal bumpers and the fullest emissions equipment of the run: judge it on frame condition.

The models

Every TR6 is the same basic car: a two-seat open roadster on a separate steel ladder frame, with double-wishbone front suspension, independent semi-trailing-arm rear suspension, front disc brakes and rear drums, and the 2498 cc straight six driving the rear wheels through a four-speed manual gearbox. There is no coupรฉ, no automatic and no other body style โ€” the factory steel hardtop and the Laycock overdrive are options, not models. What the badge does not tell you, the commission number does. It sits on a plate in the engine bay on early cars and on the door jamb or windscreen pillar on later ones, and its two-letter prefix is the car's identity: CP and CR mean petrol injection, CC and CF mean carburettors, and the split between the pairs is the 1973 model year. Read the prefix before anything else in a listing โ€” it settles the fuel system, the original market and most of the value in one glance.

ModelYearsEngineOutputBuiltCharacter
TR6 PI (CP commission)1969โ€“19722.5 six (2498 cc), Lucas mechanical injection, 9.5:1 compression150 hpA small minority of a 90,000-plus runThe full-performance car; sharp throttle response, the connoisseur's TR6
TR6 PI (CR commission)1973โ€“19752.5 six (2498 cc), Lucas injection, milder camshaft124 hpA small minority of the runThe detuned PI car; torquier and easier-mannered, still injected
TR6 carburettor (CC commission)1969โ€“19722.5 six (2498 cc), twin Zenith-Stromberg 175 CDSEabout 104 hpThe bulk of production, overwhelmingly for the USThe American car in its purest form; slim bumpers, strongest US tune
TR6 carburettor (CF commission)1973โ€“19762.5 six (2498 cc), twin Zenith-Stromberg, full federal emissions tuneabout 104 hp, eroding in later yearsThe bulk of later production, overwhelmingly for the USThe federal car; big bumper overriders from 1974, raised bumpers at the end

(Outputs are period figures: DIN for the PI cars; US ratings moved between gross and net conventions during the run, so treat the carburettor figure as approximate. The great majority of the 90,000-plus built were left-hand-drive carburettor cars for North America.)

The PI cars: CP (1969โ€“72) and CR (1973โ€“75). The injected car is the TR6 as Triumph's engineers intended it: 150 hp from the CP series, 0โ€“60 mph in the low eight-second range and a top speed around 120 mph. The Lucas mechanical injection gives it its defining character โ€” instant throttle response and a hard, urgent top end no carburettor TR6 matches. For 1973 the CR series adopted a milder camshaft, cutting peak output to 124 hp in exchange for a broader torque curve and better manners in traffic; purists prize the CP car, but plenty of experienced owners prefer the CR on the road. PI production ended in early 1975, so there is no 1976 PI car whatever a listing claims. In America a PI car is a later import โ€” never officially sold here โ€” so its premium should be argued from its injection system's health, which the engines section prices.

The carburettor cars: CC (1969โ€“72) and CF (1973โ€“76). This is the TR6 America bought, and the centre of today's market. The CC cars are the purest: slim chrome bumpers without overriders, the strongest tune the US engine ever received, and the lightest emissions equipment of the run. The CF series from 1973 brought a front anti-roll bar, revised seats and progressively heavier federal equipment: large black rubber bumper overriders for 1974, then raised bumpers and a chin spoiler for the final 1975โ€“76 cars, alongside air injection and ever softer tuning. None of this makes a late car a bad car โ€” a sound 1976 beats a rotten 1970 every day of the week โ€” but the years are not interchangeable, and the premium for early cars is a premium for specification, not just age. Our pool mirrors the pattern: late CF cars dominate, with 7 of the 20 from 1976 alone.

The 1968 question, and identity generally. One car in our pool is listed as a 1968 TR6. Production began in the autumn of 1968 for the 1969 model year, so a late-1968 build is possible โ€” but the TR250, the TR6's carburettor predecessor in the TR5 body, was also a 1968 car, and titles drift by a year in both directions. The commission plate settles it: a TR6 prefix (CP, CR, CC or CF) matching the title makes it a TR6; a TR250's plate and Michelotti nose make it a different, rarer car to be priced as itself. Engine numbers share the commission prefix family, so a CF car carrying a CP engine has had a transplant โ€” a fact that belongs in the price. A trace certificate from the British Motor Industry Heritage Trust archive at Gaydon confirms build date, original colour, trim and factory options, and is the cheapest originality evidence in the classic car world. On any car priced on originality โ€” an early CP car above all โ€” it is not optional homework.

Options that move value. The Laycock overdrive is the big one: offered throughout the run, it drops cruising revs by roughly a fifth and transforms motorway use, and a working overdrive is worth a real premium โ€” but test it, in third and top, under load, because a seller's "fitted" and a buyer's "working" are different claims. Wire wheels were offered early in the run, but most US cars sit on the standard 5.5-inch steel wheels with trim rings, and a car on sound steels is worth more than one on tired wires with worn splines. The factory steel hardtop is a desirable extra when it comes with the car; the vinyl soft top is a consumable, not a value item. Originality of colour matters more to value than the shade itself โ€” though red cars have always sold fastest, which is why 4 of the colour-stated cars in our pool wear it.

A Triumph TR6 listed as a 1968 car with overdrive and wire wheels, from College Point, New York
A TR6 listed as a 1968 car, with overdrive and wire wheels, in College Point, New York. The year is the thing to verify โ€” production began in late 1968 and the TR250 it replaced is also a 1968 car โ€” so let the commission plate, not the listing, tell you which car this is.

Engines and gearboxes

The 2.5-litre six: one engine, two characters

Every TR6 runs the same basic engine: a 2498 cc overhead-valve straight six with a cast-iron block and head, a long 95 mm stroke against a 74.7 mm bore, rooted in the Standard and Triumph saloon range of the early sixties. It is a torque engine, not a revver โ€” peak power arrives around 5,500 rpm, and the performance lives in a broad, lazy mid-range. A healthy one starts readily, idles with a lumpy, purposeful beat, pulls cleanly from 2,000 rpm, and shows strong oil pressure: expect the gauge well up at cruising speed, and treat a hot idle figure that collapses toward the bottom of the gauge as wear talking, not character. These engines leak a little oil by design โ€” the rear main uses a scroll-type seal that weeps by intent rather than failing โ€” so judge leaks by volume: a misting is a TR6, a puddle that grows is a job.

The differences that matter are compression and camshaft. PI cars run 9.5:1 compression and, in CP form, a long-duration camshaft that gives the 150 hp figure and a cammy idle; CR cars keep the compression but adopt a milder cam for the 124 hp tune. US cars run lower compression โ€” 8.5:1 early, dropping to about 7.75:1 in the later emissions years โ€” and the mild cam throughout, which is why the US engine feels softer at the top end, and why bolting PI equipment onto a low-compression US engine does not make a PI car. The other wear items are conventional: the single-row timing chain stretches and rattles at start-up; cam lobes and followers wear on neglected oil; the rocker shaft grooves, giving a top-end tick adjustment cannot cure; valve guides wear until the car smokes on the overrun. A full professional rebuild โ€” rebore, crank grind, pistons, chain, guides and gaskets โ€” runs roughly $5,000โ€“9,000, which is why a documented recent rebuild earns a genuine premium, and why the test in the next paragraph matters more than any other single check on the car.

That test is crankshaft endfloat, the TR6 six's one defining weakness. The crankshaft's fore-and-aft location is controlled by semicircular thrust washers either side of the rear main bearing. Every press of the clutch pedal pushes the crankshaft forward and loads those washers, and on a neglected engine they wear thin โ€” and then, in the classic failure, drop out of their housings into the sump altogether. Endfloat grows from a specification of roughly 0.006โ€“0.008 inches to twenty, thirty, eventually over a hundred thousandths, at which point the crank walks far enough to wreck the block's thrust faces and turn a washer replacement into an engine-out rebuild. The check takes thirty seconds: with the engine off, lever the front pulley gently fore and aft and feel for movement โ€” a barely perceptible click is healthy, visible travel is not. Or have a helper press the clutch while you watch the pulley step forward. Caught early, oversize thrust washers โ€” pinned in place by a specialist so they cannot drop again โ€” are a sump-off job in the $400โ€“900 range. Caught late, you are pricing the rebuild above. Never skip this check, however sweetly the car runs: a dropped-washer engine idles beautifully right up to the moment it destroys itself.

Cooling matters because the six runs warm by modern standards and the system has no margin for neglect. The radiator silts, the thermostat sticks, the water pump bearing weeps and then rumbles, and a car that has sat grows a system full of scale. On the test drive the temperature gauge should climb to the middle and stay there, including in traffic; a needle that creeps upward puts the radiator and pump budget โ€” roughly $400โ€“900 for a recore or quality replacement radiator and a pump, fitted โ€” into the negotiation. Electric fan conversions are common and, done properly, a genuine improvement in modern traffic; done badly, they are a fault you inherit.

Lucas petrol injection: the PI cars

The PI system is Lucas Mk II mechanical petrol injection, adapted from racing practice. An electric pump in the boot โ€” originally a Lucas unit, now very often a Bosch replacement โ€” delivers fuel at around 100โ€“110 psi to the metering unit, regulated by a pressure relief valve. The metering unit is driven at half engine speed from the distributor drive; inside it, a rotating shuttle meters fuel to the six injectors in firing order, the quantity governed by a diaphragm exposed to inlet manifold vacuum, so the system reads engine load from depression exactly as a carburettor does, only far more precisely. The injectors are pintle valves that open at roughly 50 psi. There is no electronics anywhere in it. When it is right, a PI car starts instantly, hot or cold, and answers the throttle with a sharpness no carburettor car matches. When it is wrong, it defeats guesswork โ€” which is why PI cars divide so sharply in price between documented, specialist-maintained examples and everything else.

The failure modes have mechanisms, and a buyer should know them. The metering unit's internal seals and diaphragm perish โ€” ethanol-blended fuel accelerates this, attacking rubber specified for leaded petrol โ€” and the symptoms are a rich idle, fuel smell, poor hot starting and a car that will not hold a tune. The electric pump runs hot in the boot, especially the original Lucas design, and vapour and cavitation give the classic PI complaint: the car falters or cuts out in hot traffic and restarts when cool. A Bosch pump conversion with a modern filter and a correctly set relief valve is the accepted cure, and its presence is a plus, not a deviation worth penalising. Injectors clog or dribble, giving a one-cylinder misfire owners chase through the ignition for months; a set tested and cleaned, or replaced, is a few hundred dollars and transforms a car. The vacuum signal is the system's brain, so a split vacuum pipe between manifold and metering unit richens the mixture across the board โ€” a two-dollar hose causing a four-figure misdiagnosis. A metering unit rebuild by one of the handful of specialists who still calibrate them on a bench runs roughly $800โ€“1,500, and a recent specialist invoice for the unit, the pump and the injectors means the seller has already paid part of the PI premium for you. Budget for that work, undocumented, on any PI car that runs rich or starts reluctantly when hot โ€” and never accept "they all do that" as a diagnosis, because a sorted PI car does none of it.

Twin Strombergs: the US carburettor cars

US cars breathe through twin Zenith-Stromberg 175 CDSE carburettors โ€” constant-depression instruments in the SU family, in which a rubber-diaphragmed air piston rises and falls with airflow and carries the needle through the jet. They are simple and well supported, and almost everything that goes wrong with them is rubber or wear rather than design. The diaphragms are the first check: they perish and split with age and ethanol, and a torn diaphragm gives a flat spot, hesitation and a car that will not pull cleanly โ€” symptoms routinely blamed on ignition or compression. A pair of diaphragms costs very little; the skill is in suspecting them. The dashpots need their oil, and a car that stumbles on throttle opening with dry dashpots is a two-minute fix masquerading as a fault. Worn throttle spindle bushes are the deeper wear item: they leak air at idle, giving a wandering, un-tuneable idle, and curing them means reaming and re-bushing the bodies, part of a proper pair rebuild at roughly $400โ€“800. Needles and jets wear oval together and richen the mixture; floats and needle valves flood; the CDSE's temperature compensators and bypass valves stick and confuse tuners who do not know they exist.

Around the carburettors sits the federal emissions apparatus. Early CC cars have modest equipment; CF cars add an air injection pump, charcoal-canister vapour control, an anti-run-on valve and increasingly elaborate plumbing. Much of it has been removed from surviving cars over the decades. Whether that matters depends on your state's inspection regime โ€” a car that must pass a visual emissions check in California is a different purchase from the same car in a state with no such test. Do not accept the folk wisdom that a de-smogged US engine is therefore a 150 hp engine: the power gap to a PI car lives in compression and camshaft as much as in the plumbing. Judge a US car on how crisply it runs as a US car โ€” instant cold starting on the choke, a steady idle around 800โ€“850 rpm, clean pulling to 4,500 rpm. A sorted Stromberg car is a sweet thing; a neglected one is a tuning seminar you pay for by the hour.

Gearboxes and the Laycock overdrive

The gearbox is Triumph's own four-speed with synchromesh on all forward gears, strong, slick by period standards and long-lived on clean oil. Judge it on second-gear synchromesh โ€” the first to wear, crunching on a fast downchange long before it complains going up โ€” on jumping out of gear on the overrun, which means worn selectors or bearings and a rebuild in the $1,200โ€“2,500 range, and on the clutch: judder points at oil contamination or a tired driven plate, and a full clutch replacement runs roughly $700โ€“1,300 fitted. Gearbox and overdrive share their oil on overdrive cars, and low or filthy oil is the root of half the overdrive faults in existence, so the level is a viewing-day check.

The overdrive is a Laycock de Normanville unit, hydraulically engaged by an electric solenoid, in two types divided by the same 1973 line: A-type on earlier cars, J-type from 1973. Both operate on third and top gears, giving six usable ratios and dropping cruising revs by about 22 percent. Engagement should be near-instant, a firm step down in revs within a second of flicking the switch; disengagement equally clean. The faults are electrical first, mechanical second: chafed wiring where the loom crosses the gearbox, a failed solenoid (a $100โ€“200 part), inhibitor switches that prevent engagement or, worse, allow it in reverse, where it destroys the unit. Hydraulic wear gives slow, slipping engagement that worsens hot. A rebuild runs roughly $1,000โ€“1,800 at a specialist. A non-overdrive car is not a defective car โ€” many US cars were sold without it โ€” but on a car you intend to drive distance, the overdrive is the one option worth paying a premium for, and the one whose operation you must verify yourself, under load, in both gears, before money moves.

Problem areas

Everything in this section follows from the car's construction: a cosmetic body bolted to a separate steel frame, both fifty years old, most of them having lived in the states where our pool of 20 cars clusters โ€” New Jersey, North Carolina and Pennsylvania lead the listings. Salt states are frame states. Assume every TR6 needs the forensic examination below, and remember the ordering: almost everything mechanical here can be fixed with money and patience, but structural frame rust reliably turns a bargain into a parts car. The frame examination and the endfloat test from the engines section decide whether you continue at all. Everything else is negotiation.

Frame and body: the rust map

Start with the frame, from underneath, on a lift if the car is priced as anything but a project. The frame is a ladder of box-section rails with outriggers carrying the body, and it rusts from the inside out at predictable addresses. Work through them in this order.

The rear trailing-arm crossmember and its brackets. This is the TR6's structural weak point and the single most important check on the car. The semi-trailing arms pivot from brackets welded to a crossmember at the back of the frame โ€” the area mechanics call the T-shirt pressing, after the shape of the frame pressing there. The brackets trap mud and salt against the crossmember, the metal perforates, and in the advanced case the brackets tear away from the frame, at which point the rear suspension is attached to rust. Prod the crossmember along its full width and lever at each bracket; surface scale is treatable, perforation is fabrication. A specialist can replace a crossmember and brackets, but it is body-lifted work in the $2,500โ€“5,000 range, and it rarely comes alone. A car needing it is a project whatever its paint says.

Outriggers and the middle of the frame. The outriggers that carry the body sills rust where they meet the main rails, and the rails perforate along their lower faces where they trap road film. The front crossmember and the front suspension turret area take stone damage and rust at the seams. None is as immediately dangerous as the trailing-arm mounts, but together they are the difference between a frame needing local repair and one needing replacement โ€” and a replacement frame, or a full frame restoration with the body off, is a five-figure decision that re-prices the entire car.

Differential mounting pins. The differential bolts to the frame through mounting pins, and the front pins crack their welds and tear at the frame โ€” a design weakness, not a rust issue, though rust accelerates it. The symptom is a clunk from the rear on taking up drive, in a car whose universal joints prove sound. On the lift, look for cracked paint and movement at the pins. Re-welding and reinforcing them is a known specialist job, roughly $600โ€“1,200 with the differential out; reinforcement plates fitted as a precaution appear on well-kept cars โ€” a plus point, not a worry.

The body. The shell rusts at its own addresses, and because the wings bolt on, panel rust is cheaper here than on a unitary car โ€” which tempts sellers to call all of it cosmetic. It is not, where the body mounts and inner structure are involved. The sills โ€” rocker panels โ€” are the headline: inner and outer sills rot from the bottom up, the body sits on them, and bubbling along the sill's lower edge means the inner sill and floor edge are going with it. A sill pair replaced and painted runs roughly $1,200โ€“2,500 a side depending on how much inner structure travels with it. Floors perforate at the front footwells, where water from a leaking windscreen seal or scuttle sits under the carpets. The boot floor rusts around the spare wheel well and the fuel tank, fed by a perished boot seal. Door bottoms fill with water through blocked drain slots and bubble along the lower edge โ€” run a fingertip along every door's bottom edge and feel for it. Front wings rust at the top seam and around the headlamp bowls; rear wings at the lower edges and along the bolted joint to the deck; the rear valance perforates; the battery tray rots under the battery from acid, invisibly until you lift the battery out. A magnet wrapped in cloth will map filler for you. No single panel kills a car โ€” repair sections for sills, floors and valances are all available โ€” but the arithmetic adds up fast, and a car needing all three is a body restoration wearing a driver's price tag.

A blue 1974 Triumph TR6 from Freehold, New Jersey
A blue 1974 TR6 from Freehold, New Jersey โ€” a CF-commission federal car from the first year of the big black bumper overriders. New Jersey is salt country: on this car the trailing-arm crossmember, the outriggers and the inner sills are the purchase, and the paint is the wrapping. Price it from a lift, not from this angle.

Engine and driveline wear

The thrust washers own this section, because they own the engine's survival: the endfloat test in the engines section is repeated here as a verdict. Visible pulley movement is an engine-out conversation, and dropped washers with damaged thrust faces mean the $5,000โ€“9,000 rebuild. Everything else in the driveline is cheaper, but it accumulates โ€” a car can carry three of the following faults at once while still driving well enough to sell itself.

Differential. The Triumph differential is a saloon-derived unit, geared 3.45:1 in PI cars and 3.7:1 in US cars, and it whines and clunks with age rather than failing outright. A whine that changes with throttle load is pinion and crownwheel wear; a clunk on take-up is backlash, worn universal joints, or the cracked mounting pins above โ€” the inspection's job is to separate the three, because their prices differ by an order of magnitude. A rebuild runs roughly $900โ€“1,500.

Half-shafts, splines and rear hubs. The rear driveshafts use sliding splines that seize with age and dried grease, and a seized spline produces the car's famous handling fault: the rear end snatches and twitches under power in corners as the spline locks and releases instead of sliding โ€” owners call it TR twitch. The cure is stripping, cleaning and greasing the splines, or fitting modern constant-velocity conversions, an upgrade rather than a deviation. Universal joints wear and click. The rear hub units are the safety item: taper-roller assemblies carrying the stub axle, they wear loose, and a neglected hub can fail in a way that costs a wheel's location. Rock each rear wheel hard at twelve and six o'clock; play in the hub, not the bushes, prices a rebuild โ€” roughly $400โ€“700 a side with quality bearings โ€” and upgraded hub designs are the accepted permanent fix. Do not drive a car with loose rear hubs any distance.

Clutch and its hydraulics. The clutch is hydraulic, Girling master and slave, and the hydraulics perish on a standing car: a clutch that creeps with the pedal held down is a master cylinder seal passing, not a dragging plate. The release mechanism has its own known weakness โ€” the tapered pin locating the release fork on the cross-shaft shears, giving a pedal that suddenly goes light and a clutch that will not release โ€” and the strengthened fork modifications in the parts trade exist because the original design earns them. A clutch job is gearbox-out work, $700โ€“1,300 fitted, and on any car where it is being done, the fork pin and the thrust washers are inspected in the same hour, because the faults travel together.

Suspension, steering and brakes

Front suspension. Double wishbones, coil springs and telescopic dampers: trunnions at the bottom of the vertical links, ball joints at the top, rubber bushes throughout. The trunnions are the discipline item โ€” brass bushes running on the link's thread, they want oil (not grease, whatever the last owner used) at service intervals, and a starved trunnion wears until the steering goes heavy and notchy and, in the neglected extreme, the link's thread fails. Feel for notchiness lock to lock with the weight off, and price a trunnion and bush refresh at roughly $500โ€“1,000 a side fitted if the car steers like a truck. A full front-end bush and joint refresh is one of the best-value transformations you can buy a TR6.

Rear suspension. The semi-trailing arms pivot on rubber bushes that perish and split, letting the rear wheels steer themselves under load โ€” a car that wanders at the back on a trailing throttle is usually bushes and tired coil springs before it is anything bent. Replacing the bushes is awkward, rusted-bolt work, roughly $600โ€“1,200 the pair fitted, and it belongs in the same conversation as the crossmember those arms mount to: there is no sense re-bushing arms bolted to a perforated bracket. Rear lever-arm dampers on early cars and telescopic conversions on many survivors both work; a telescopic conversion with sound brackets is a plus.

Steering. Rack and pinion, direct and full of feel when right. Wear shows as play at the rack's inner joints and tired rack mounts โ€” the original rubber mounts let the rack shuttle slightly, and solid mount conversions are a popular, legitimate sharpening. The column's flexible coupling perishes. Judge it on centre play and on whether the car tracks straight without correction.

Brakes. Front discs, rear drums, servo assistance on US cars, and a dual-circuit system on federal cars whose pressure-differential warning valve seizes and weeps. The hydraulics perish in storage: seized calipers, leaking rear wheel cylinders, a master cylinder passing internally so the pedal sinks slowly at a standstill. A full hydraulic refresh runs roughly $800โ€“1,800 fitted and is the standard first-year bill on a standing car. The handbrake is famously feeble even when adjusted; judge it as adequate or not, not against a modern car. Brake pipes rust along the frame rails, and original steel pipes in a salt state want inspecting line by line on the lift.

Interior, hood and electrics

Interior. The cabin is vinyl over foam and board, with a veneered wooden dashboard fascia, and it ages in sunlight and heat. Seat foams collapse โ€” sit in the driver's seat, because it goes first, and once you can feel the frame through the cushion the job is foams and covers together, roughly $400โ€“800 a seat with a kit at home, more at a trimmer. Seat diaphragms and webbing sag beneath the foam and mimic foam failure for a fraction of the price, so diagnose before ordering. The dashboard veneer cracks and lifts at the edges; refinishing the fascia is specialist work, and a sun-cracked dash top pad is a replacement part, not a repair. Carpets are a kit and an afternoon. None of this is structural and all of it is visible, so a tired interior is the most negotiable part of any TR6 โ€” price it from the catalogues, where every piece is available.

Hood and weather equipment. The vinyl soft top is a consumable: budget roughly $600โ€“1,200 for a quality replacement hood fitted, and judge the frame and header rail rather than the fabric โ€” bent frame irons and a rotted header rail are the expensive parts. What matters structurally is what the hood has let in: a car that has lived outside under a perished top has wet floors. Window regulators wear; door seals perish and whistle. Test the heater in July anyway: a heater matrix leak fogs the screen with coolant mist and is a dashboard-fiddly job out of proportion to the part's price.

Electrics. Lucas equipment, an alternator on all TR6s, and a fuse box famously containing just three fuses, so several circuits share protection and a single fault can present in odd places. Fifty-year-old Lucas faults live at the connections: bullet connectors corrode, earth straps rot, and the symptoms โ€” dim lamps, wandering gauges, an intermittent everything โ€” are cured with a wire brush and patience rather than parts. The voltage stabiliser behind the gauges fails and sends the fuel and temperature needles on excursions; it is a cheap part and a classic false alarm. Later cars carry a ballast-resistor ignition circuit whose resistive wire fails and gives a car that starts on the key's start position and dies on release โ€” a two-minute diagnosis once you know it. The ignition switch itself wears and causes intermittent total electrical death. A car where everything electrical works is a car that has been used and maintained, and on a TR6 that signal is worth more than a folder of oil-change receipts.

How to inspect one

Allow at least an hour, bring a torch, a magnet wrapped in cloth and a small lever for the endfloat test. If the car passes you, pay for a lift inspection before money changes hands โ€” on a TR6 it is the best money in the whole purchase. Work in this order: the early steps can end the viewing, the later ones only price it.

  1. Start with the paperwork and the commission plate. Match the commission number on the plate โ€” engine bay on early cars, door jamb or windscreen pillar later โ€” to the title, and read the prefix: CP or CR means injection, CC or CF means carburettors. Check the engine number carries the matching prefix family; a CF car on a CP engine has had a transplant, which belongs in the price. Ask for the history file and any heritage certificate, and treat a thick folder of invoices as worth real money, because on this car it is.
  2. Cold start, and the endfloat test before you drive anywhere. Insist the engine is stone cold when you arrive. It should start readily โ€” instantly on injection, on the choke with carburettors โ€” and settle without blue smoke. Then, engine off, do the thrust-washer check from the problem areas section: lever the front pulley fore and aft, and have the seller press the clutch while you watch it. Visible movement ends the negotiation about everything except project pricing.
  3. Under the car: the frame decides. Torch along the trailing-arm crossmember and lever at its brackets โ€” the T-shirt area from the rust section โ€” then the outriggers, the rails' lower faces, the front crossmember and the differential mounting pins, looking for the cracked paint that betrays a tearing pin. Perforation at the trailing-arm mounts or torn diff pins is structural and re-prices the car as a project. Read the underseal as you go: patchy and honest is original; a fresh uniform black coat over everything is a question.
  4. Sills, floors and boot. Press hard along both sills; lift the carpets in both footwells and prod the floor pans; open the boot, lift the spare wheel and look at the well and the floor around the tank. Wet carpets in a dry-stored car mean leaking seals and rust already started. Run a fingertip along the bottom edge of every door for the bubbling that means the door has been holding water.
  5. Body and gaps. Walk the magnet over the sills, wheel arches, lower wings and rear valance โ€” filler announces itself. Check the front wings along the inner-wing seam, the rear wings at their bolted deck joint, the headlamp bowls and the battery tray, lifting the battery if the seller allows. Panel gaps that wander tell an accident story. Count the rust honestly: bolt-on wings are cheap, inner structure is not.
  6. Engine in detail. On a PI car, look for the Bosch pump conversion or a healthy original, smell for fuel around the metering unit, and note any split or perished vacuum pipe โ€” the rich-running causes from the engines section. On a carburettor car, check the dashpot oil and note what emissions equipment survives against your state's rules. Everywhere: oil leaks graded by volume, and the radiator's core condition.
  7. The test drive: gearbox and overdrive. Fifteen minutes minimum, including a fast road. The gearbox should change cleanly up and down; a crunch on a hurried downchange into second is the synchromesh bill from the engines section introducing itself. If overdrive is fitted, engage it in third and in top, under load: engagement should step the revs down within a second, with no flare or slip, and disengage as cleanly. A car that will not demonstrate its overdrive does not have one, for pricing purposes.
  8. The test drive: driveline and rear end. Listen for the differential โ€” a load-dependent whine is wear, a clunk on take-up is backlash, joints or the mounting pins from step 3. Feel for TR twitch: a rear end that snatches under power in a gentle corner is seized half-shaft splines, not character. Brake firmly from speed: the car should stop straight, the pedal stay hard and high, and a pedal that sinks slowly at the next junction is a master cylinder passing.
  9. Suspension and steering on the move and at rest. The steering should be light, direct and free of centre play; heaviness and notchiness point at the trunnions from the problem areas section, wandering at speed at bushes. Rock each wheel at the kerb โ€” front play against trunnion and bearing wear, rear play against the hub check, because a loose rear hub is the one fault on this list you do not drive home on.
  10. Heat, idle and electrics. Let the car idle hot after the drive. The temperature needle should hold the middle of the gauge in traffic; oil pressure should stay respectable at a hot idle. Work everything electrical: lights, indicators, wipers on both speeds, washers, heater blower, gauges โ€” remembering the voltage stabiliser's trick of sending the needles wandering on a healthy car. On a later car, a stall the moment the key returns from start to run is the ballast wire, not a mystery.
  11. Stance and ride height. Stand back and look at the car level, from front, rear and both flanks. It should sit even, corner to corner, with the rear wheels upright. A sagging rear or odd rear camber is springs and bushes; a corner down is a spring or a frame question, and step 3's evidence decides which. Photograph any car you view from this distance โ€” stance faults you talk yourself out of in person are obvious in a picture.
  12. Interior and hood last. Sit in the driver's seat and feel for the frame through the cushion; check the webbing underneath before condemning the foam. Work the hood up and down once โ€” frame irons straight, header rail sound โ€” and check the dash veneer at its edges. A sound original interior is the hardest part of a TR6 to recreate, so weight it heavily, but never let it outvote a rotten frame.

Values

The market block beneath this guide carries the current numbers โ€” the cars listed now and the recorded sales โ€” refreshed at every build, so this section deliberately carries none. What it teaches instead is how to read those numbers, because the TR6 market is one of the most condition-sensitive in the classic world: the spread between the cheapest and dearest examples of the same model year is wider than the spread between years, specifications or colours.

The first driver is the frame, and it is not close. A TR6 with a sound, original frame, sound sills and a documented history sits in a different market from an identical-looking car needing a trailing-arm crossmember and outriggers, because the second car's repair bill, honestly counted, consumes a large fraction of the finished car's worth. This is why asking prices mislead on this model: sellers price the paint, the market prices the structure, and the gap between the two is where TR6s sit unsold for months. Compare a listing against the recorded sales beneath this guide by structural condition, not by year and colour โ€” and treat any car priced at driver money whose frame you have not seen from a lift as priced on hope.

The second driver is specification, and here the market splits by ocean. PI cars carry a clear premium in Britain and Europe, where they were sold new and where the 150 hp CP car has a competition-bred reputation; in the United States, where the PI car was never officially sold, the premium is thinner and more fragile, resting on a smaller pool of buyers and of specialists who can calibrate a metering unit. An imported PI car in America has to be exceptional โ€” documented, sorted, demonstrably crisp โ€” to hold its premium against a good carburettor car. Within the US mainstream, early CC cars earn a modest premium for their slim bumpers and stronger tune, working overdrive earns a real one on any year, and the late CF cars' heavier bumpers cost them a little against an equivalent early car โ€” a little, not a lot: a sound 1976 remains worth more than a tired 1970. Originality pays where it can be proved: matching numbers, the heritage certificate, the original colour. Colour itself moves saleability more than price โ€” red cars find buyers fastest, a liquidity fact, not a quality one.

The third driver is the project-versus-driver gap, and on the TR6 it is a chasm with a trap in it. A non-running or structurally rusty car is worth parts money, and parts money here is genuinely modest, because the trade supplies so much new that used mechanical parts are cheap; what a project actually sells is its frame, its identity and its restorable panels. Between the project and the good driver sits the dangerous middle: the running car with shiny paint over an unexamined frame, where most asking prices cluster and most buyers overpay. A full restoration โ€” frame, body, paint, engine, trim โ€” costs more than a finished car sells for, which is why experienced money buys the best car available. Negotiate on the levers that actually move price: documented structural condition, a demonstrated overdrive, a recent engine invoice, a heritage certificate โ€” paperwork and steel, not detailing. Asking prices on the big marketplaces, where most of our 20-car pool originates, run optimistic against achieved prices; the recorded-sales block below is your anchor.

Parts and ownership

The TR6 is one of the best-supported classics of its era: more than 90,000 were built, the American population is enormous, and the specialist trade โ€” Moss Motors in the US, Rimmer Bros in Britain, and marque specialists beneath them โ€” catalogues the car down to individual fasteners. The club scene is equally deep: the Vintage Triumph Register in the US, the TR6-focused 6-PACK club, and the TR Register in Britain hold the technical knowledge and the classifieds. Join one before you buy, not after.

Easy: service items, filters, plugs and points, brake discs, pads, calipers and hydraulics, Stromberg rebuild kits and diaphragms, suspension bushes and joints, trunnion kits, exhaust systems, hood vinyl and tonneau covers, seat foams, covers and carpet sets, glass rubbers and seals, and almost every electrical consumable. Order today, fit this weekend, at prices close to modern-car money. PI service parts are equally available; it is calibration knowledge that is scarce, not hardware.

Harder and dearer: metering unit rebuilds, a handful-of-specialists job at roughly $800โ€“1,500 as the engines section sets out; frame repair sections fitted properly, where the panel is cheap and the labour is the bill; rear hub units, where the upgraded specialist designs are worth their premium over the cheapest exchange units; a correct early dashboard veneer; factory hardtop fittings; and good used PI heads and early CP camshafts, where supply is finite. A quality repaint starts in five figures โ€” which is why the mantra of this guide is to buy the frame and the body, and fix the mechanics.

Running costs. A sorted TR6 is a realistic regular-use classic: fuel consumption in the low twenties per gallon on a run for a carburettor car, servicing any competent independent can handle, insurance in line with other classics of the value. The budget line that catches new owners is the first year. Catching up deferred maintenance on a running car โ€” hydraulics, bushes, cooling, thrust washers checked, splines freed โ€” honestly costs $2,000โ€“5,000 before you improve anything, and recommissioning a car that has sat for years runs $4,000โ€“8,000 at a shop, because standing is this car's second-worst enemy after salt: hydraulics seize and pass, diaphragms perish, splines lock, and ethanol fuel eats old rubber while leaving varnish in a rusting tank. Buy a car in regular use over one that has been asleep, even at a higher price โ€” on a TR6, use is maintenance.

A red 1976 Triumph TR6 from Homewood, Illinois
A red 1976 TR6 from Homewood, Illinois โ€” another final-year car, the joint-commonest year in our pool. A late car like this is the ownership proposition in its easiest form: deep parts support and a specification every specialist knows. What decides its worth is not the year but the frame underneath and the invoices in the glovebox.

Which one to buy

And the rule that overrides the above: buy the soundest frame you can find, in the spec you can live with. Thrust washers, metering units, differentials and dashboards are all fixable at prices you can plan for. A rotten frame costs more to put right than the finished car will be worth โ€” and it is the one thing about a TR6 that can never be made original again.

See the 20 TR6 cars currently listed.