Porsche 911 buyer's guide
Porsche 911 -- the model's own buyer's guide: variants, values and what to check.
Years listed: 1974-1998 ยท Series: 911
Overview and history
This is the model-level companion to our 911 series guide, and it assumes you have already decided the question that guide answers โ that you want an air-cooled Porsche 911. What follows is the next question, the one that actually spends your money: which generation, which engine, which gearbox, and how do you tell a sound example from an expensive one wearing good paint. The cars behind this guide are the ones our listings actually turn up, and they cluster in two places: the long-lived G-series cars of 1974 to 1989 โ the impact-bumper 911s, from the early 2.7s through the SC to the 3.2 Carrera โ and the 993 of 1995 to 1998, the last of the air-cooled line. Between them sits the 964 of 1989 to 1994, covered here in its buying specifics even though it is thinner in our current pool. The water-cooled 996 that followed the 993 is a different car with a different fault list, and it gets only a boundary mention: if your search drifts past 1998, you have left this guide's territory.
The G-series is where the classic 911 became the car the world pictures. The impact bumpers arrived for 1974 to meet US safety rules, and with them came a tougher, more finished car: galvanised panels phased in from 1976 and fully galvanised shells by the late seventies, interiors that could survive daily use, and engines that grew from the troubled early 2.7 through the near-bulletproof 3.0 of the SC (1978โ83) to the 3.2 Carrera (1984โ89), the car most experienced buyers name as the sweet spot of the air-cooled era. The 964 modernised everything underneath โ coil springs in place of torsion bars, power steering, ABS, a 3.6-litre engine โ while keeping the classic silhouette. The 993, from 1995 in the US, refined it again: a multi-link rear axle, a six-speed gearbox, and styling most owners consider the prettiest of all. It was also the end. Every 993 is now at least a quarter-century old, every G-series car older still, and the buying logic is the same for all of them: simple, strong, fully rebuildable cars whose expensive failures are specific, known in advance, and detectable before purchase if you inspect for them by name. That is what this guide is for.
Two facts about the market shape everything below. First, most surviving examples have passed through an era of cheapness, when they were run on budgets or stored badly, and then an era of rising values, when cosmetic restoration became profitable whether or not the mechanical work underneath was done. A shiny G-series car with a tired engine is a commoner sight than a scruffy one with a fresh rebuild, and the shiny one costs more to own. Second, almost everything can be fixed at prices you can plan for โ but an engine rebuild is the price of a good used car on its own, and structural rust on an early, pre-galvanising car can exceed the car's value. The discipline that protects you is the specialist pre-purchase inspection, compression and leak-down numbers in writing, and a service history you can read rather than a story you are told.

The models
At model level the 911 range resolves into four buying propositions โ the early G-series 2.7 cars, the SC, the 3.2 Carrera, and the two 3.6-litre generations, 964 and 993 โ each in coupe, Targa and Cabriolet form, each with a Turbo variant at the top of its generation. The table gives the spine of the US-market range; outputs are period figures for US cars, which differ from European ones, sometimes sharply on the emissions-era cars.
| Model | Years | Engine | Output | Built | Character |
|---|---|---|---|---|---|
| 911 / 911S (2.7) | 1974โ1977 | 2.7 flat-six, CIS injection | 150โ165 hp | Tens of thousands across the run | The raw early G-car; cheapest entry, dearest engine risks |
| 911 SC | 1978โ1983 | 3.0 flat-six, CIS injection | 172โ180 hp | About 59,000 coupes, Targas and Cabriolets | The durable all-rounder; the value heart of the range |
| 911 Carrera 3.2 | 1984โ1989 | 3.2 flat-six, Motronic injection | 200โ217 hp | About 76,000 | The developed G-car; G50 gearbox from 1987 is the prize |
| 911 Carrera (964) | 1989โ1994 | 3.6 flat-six, twin-plug | 247 hp | About 62,000 all 964s | The modernised classic; all-wheel-drive C4 alongside |
| 911 Carrera (993) | 1995โ1998 | 3.6 flat-six; Varioram from 1996 | 270โ282 hp | About 68,000 all 993s | The last air-cooled car; the collector default |
| 911 Turbo (930) | 1975โ1989 | 3.0/3.3 flat-six, turbocharged | 234โ282 hp | About 18,000 | The widowmaker legend; a separate market and skill set |
The 2.7 cars (1974โ77). The first impact-bumper cars kept the 2.7-litre engine from the last of the early cars, with Bosch K-Jetronic (CIS) injection for the US. In standard tune the US car made modest power, the S a little more, both strangled further in California. These are the lightest, rawest G-series cars and the cheapest way in โ and they carry the generation's defining engine fault, the pulled head studs covered in detail below. Buy one on the strength of documented engine work, or do not buy one. US cars of 1975โ77 also carried thermal reactors, which held exhaust heat against the cylinder heads and cooked them; most were removed decades ago, but the damage, if it happened, was done then and shows up in the leak-down test now.
The SC (1978โ83). Porsche consolidated the range into one model, the Super Carrera, with a 3.0-litre engine on the stronger Turbo-derived crankcase. Power barely rose on paper, but the character changed completely: this is the engine that built the air-cooled 911's reputation for taking mileage. The Cabriolet arrived for 1983, the first factory 911 convertible since the 356. An SC is the rational classic 911 โ galvanised shell, strong engine, simpler specification โ and in our current pool the early-eighties cars are among the most numerous, which is as it should be: this is where the supply is.

The Carrera 3.2 (1984โ89). The 3.2 brought Bosch Motronic electronic engine management โ the first in a production 911 โ more power, better economy, and a richer specification: bigger brakes, a better cabin, optional sport seats and the whale-tail spoiler most people picture. The generation splits in two at 1987, when the 915 gearbox gave way to the Getrag G50, a stronger, sweeter-shifting box that transforms the car to drive. A G50 Carrera is the most sought-after mainstream G-series specification, and the market knows it. The run closed in 1989 with the Speedster, a low-windscreen special on the wide Turbo-look body โ rare, collectible, and priced in a different conversation.


The 964 (1989โ94). Under a body that looks like a smoothed G-series sits a largely new car: coil-spring suspension, power steering, ABS, a proper heating and ventilation system, and the 3.6-litre twin-plug engine. The Carrera 4 added all-wheel drive โ the first in a production 911 โ alongside the rear-drive Carrera 2, the lighter, simpler, more sought-after car now. Tiptronic was offered on the Carrera 2. The 964 was the unloved 911 for years and has been re-rated sharply upward; its buying specifics โ early cylinder-head sealing, the dual-mass flywheel, the distributor vent โ are covered in the problem sections. The RS America of 1993โ94 is the collectible of the range.
The 993 (1995โ98). The last air-cooled 911, and for many buyers the only one they are looking for. A multi-link rear suspension calmed the old car's lift-off habits, the gearbox gained a sixth speed, and from 1996 the Varioram intake lifted the 3.6 to its final air-cooled output. US cars were Carrera and Carrera S (the wide-body car), Carrera 4 and 4S, Targa โ now with a sliding glass roof โ Cabriolet, and the Turbo. The 993's premium over the 964 buys the looks, the sixth gear and the rear axle; it does not buy immunity from age, and a 993's rubber, dampers and top end all need the same forensic approach as any G-series car.


The Turbo (930, 1975โ89). Covered here for orientation, because it is bought differently: wider body, a four-speed gearbox for most of its life (five speeds only in 1989), lag-then-surge delivery, and engine work priced above the normally aspirated cars throughout. Everything in the engine and inspection sections applies with the volume turned up, and the premium for originality โ matching numbers, unmodified boost โ is the steepest in the G-series. If a Turbo is your target, the specialist inspection stops being advice and becomes the price of admission.
Engines and gearboxes
Every engine in this guide is the same idea developed over twenty-five years: an air-cooled flat-six behind the rear axle, with a magnesium or aluminium crankcase, finned individual cylinders, and a single overhead camshaft per bank driven by chains. There is no coolant and no water pump to fail; the engine is cooled by a large fan and by its oil, which is why the oil system is not lubrication with a cooling side-effect but half the cooling system itself. The dry-sump layout โ oil in a separate tank, scavenged and pressure-fed โ means the level is read warm, idling, on level ground, and an owner who checks it cold like a normal car will overfill it and then complain about smoke. Learn that one ritual and you understand half of air-cooled ownership. What changes across the generations is crankcase strength, the fuel system, and the detail metallurgy โ and those three things, in that order, are what you are buying.
The 2.7 and the 3.0 SC: CIS cars on two different cases
The 2.7 (1974โ77) is built on the magnesium crankcase inherited from the early cars, and magnesium is the root of its reputation. The case is light and, when new, adequate โ but it does not tolerate heat cycles and stud torque the way the later aluminium cases do. The heads are held by studs threaded into the case, and on the 2.7 the combination of a flexible case and exhaust-side heat from the thermal reactors lets the studs pull out of the case threads. A pulled stud means the head no longer clamps its cylinder: you hear a chuffing, exhaust-like ticking at idle, the leak-down test finds the loss, and the repair is an engine-out strip with case machining for thread inserts (Case Savers or Time-Serts) and a full stud set โ realistically a top-end rebuild at minimum. Budget $8,000โ15,000 for a properly machined 2.7 top-end and case repair at a specialist, and understand that a 2.7 that has already had this done, with invoices, is worth more than a nominally stronger car with no paperwork. The fuel system is Bosch CIS (K-Jetronic), continuous mechanical injection metered by an airflow plate: robust, well understood, and prone to its own faults โ a control-pressure regulator (warm-up regulator) that drifts and makes cold running miserable, tired injectors that dribble, and vacuum leaks at forty-year-old rubber that mimic everything. CIS faults are diagnosed with a fuel-pressure gauge set, not by swapping parts, and a seller whose CIS car "just needs a tune-up" is describing a bill of $500โ2,000 depending on what the gauges find.
The SC's 3.0 (1978โ83) is the corrective. Its crankcase is aluminium, derived from the Turbo's, with stronger stud anchorage, and the pulled-stud epidemic largely ends โ largely, not entirely, because the lower exhaust-side studs on SCs are Dilavar, an alloy chosen for its expansion match, which can corrode and snap at the head. A broken stud announces itself the same way, with ticking and a leak-down loss, and the fix is the same engine-out work at similar money, so the leak-down test matters on an SC too; it is just far more likely to pass. The 3.0 also gained a larger oil pump and, from 1980 in the US, lambda-controlled CIS with an oxygen sensor. In service it is the durability benchmark of the G-series: valve adjustment is by eccentrics and feeler gauges, a fiddly, skilled job of about $400โ700 at a specialist with the gaskets, and cars retrofitted with the later Carrera pressure-fed chain tensioners carry a visible oil line to each chain housing โ a genuinely desirable upgrade to look for. A well-kept 3.0 will run to mileages that would finish most contemporaries. Oil leaks, not wear, are its everyday issue, covered in Problem areas.
The 3.2 Carrera and the 3.6 engines: electronic management arrives
The 3.2 (1984โ89) kept the aluminium case and changed the management: Bosch Motronic combines electronic injection and ignition in one control unit, reading a flywheel reference and a cylinder-head temperature sensor. The gains are real โ cleaner starting hot or cold, better economy, stronger top end โ and the failure modes move from mechanical wear to sensors and solder. The classic faults are a failed cylinder-head temperature sensor (the early single-wire version should have been replaced by the later two-wire part; a car hard to start or cutting out warm is suspect), a tired DME relay โ the small relay powering the control unit and fuel pump, famous for failing with age-cracked solder and stopping the car dead, and equally famous as the cheap spare every owner should carry โ and idle problems from a dirty idle control valve and perished intake rubber. None is expensive; all strand you if ignored. The 3.2's mechanical signature is valve-guide wear: the bronze guides wear, the valves rock, oil is drawn down the guides, and consumption climbs past the factory tolerance of roughly a quart per thousand miles toward a quart every few hundred. Smoke on the overrun plus a consumption history are the tells; the cure is a top-end rebuild, $7,000โ12,000 done properly. A 3.2 with a documented top-end refresh is a materially better buy than a lower-mileage car without one, because guide wear tracks heat and time as much as miles.
The 3.6 of the 964 (1989โ94) is the biggest step the air-cooled engine took: capacity up, twin spark plugs per cylinder (twelve plugs, two distributors driven by a belt inside a single housing โ that belt is a service item, and when it breaks the engine runs on one plug per cylinder, sometimes barely noticeably, while unburned mixture threatens the catalyst), and hydraulic valve adjustment. Early 964s were built without a conventional cylinder-head gasket seal โ the head seals metal-to-metal โ and oil weeping at the head-to-cylinder joint ranges from normal seepage to a leak needing the later sealing modification, which is engine-out work. The 993's 3.6 is the final development: a stronger bottom end shared with the Turbo, the head-sealing question resolved, and from 1996 the Varioram intake, whose vacuum actuators and flaps add a small, diagnosable fault set. US 993s carry secondary air injection to light the catalyst at cold start โ and carbon clogs those ports until the check-engine light sets, worst on low-mileage cars used for short trips. The full cure is top-end money; many cars are managed with documented cleaning of the accessible passages and honest disclosure, and an illuminated check-engine light on a US 993 is a price conversation, never a shrug. Valve-guide wear exists on the 3.6s too, milder than the 3.2's: consumption first, smoke second, leak-down third.

Gearboxes: 915, G50, and the six-speed
The gearbox divides the G-series more sharply than any engine change. The 915 (used to 1986) is Porsche's own five-speed: light, mechanical in feel, and honest about its age. Its synchromesh โ especially on second gear โ wears, and its linkage runs the length of the car through bushes that perish, so a 915 judged on a car with a worn linkage is being judged unfairly. A good 915, with fresh bushes and correct oil, is precise and satisfying; a worn one crunches into second, baulks at first at a standstill, and raises the question of a rebuild at $4,000โ7,000, with the clutch done while the box is out. The G50 (1987โ89, Getrag-built) is stronger, uses Borg-Warner synchromesh, has a hydraulic clutch, and shifts with a shorter, more modern action. It is not immortal โ synchros wear there too, and a rebuild costs more, $6,000โ9,000 โ but it starts from a higher baseline. The market premium for a G50 car is rational; just do not pay it for a car whose box crunches, because the badge on the specification is not the condition of the synchromesh.
The 964 carried the G50 architecture forward in five speeds; the Carrera 4's all-wheel drive adds service needs of its own, and its high-pressure hydraulic system (shared with the brake booster circuit) is specialist territory. Tiptronic, the clutchless automatic on the Carrera 2, is a reliable four-speed that suits the car's touring side; it is priced lower, and its fluid-and-filter history is the whole inspection. The 993's six-speed is the G50 idea matured: close ratios, a limited-slip differential on many US cars, and synchromesh that still wears on second if the car has been hurried cold. On all of these boxes the test is the same: the first cold change into second, within the first half-mile, tells you more than any amount of warm shifting, because worn synchromesh hides once the oil is hot. Clutches are priced by generation โ a G-series clutch fitted is roughly $1,500โ2,500 with the engine out โ and the 964's early dual-mass flywheel, which can fail and rattle, is a known $2,000-plus conversation many cars have already had. Ask, and look for the invoice.

Problem areas
An air-cooled 911 fails in a short, well-documented list of ways, and almost nothing on the list surprises anyone who has read it in advance. That is the good news. The bad news is that the list is priced in engine-out labour: jobs that are trivial on a front-engined car โ a clutch, a set of head studs โ begin with removing the engine and gearbox as a unit, and the hours set a floor under every repair. So read this section as a pricing tool. Each fault below is something you can test for, ask about, or find in the paperwork before you buy, and each one you find is either a negotiation or a reason to walk to the next car, of which there are always more.
The engine: studs, guides, tensioners and oil
Head studs are the first check on any G-series car, and the mechanism matters. Each head is clamped by studs anchored in the crankcase; the exhaust-side lower studs live in the hottest, wettest environment on the engine. On the 2.7's magnesium case the studs pull out of the case itself. On the SC and 3.2, the Dilavar lower studs corrode and snap, typically at the head. Either way the symptoms are identical: a rhythmic chuffing or ticking at idle that rises with revs, an oil mist around the base of the affected cylinder, and a leak-down test showing the loss escaping past the head joint rather than past rings or valves. You cannot see a broken stud without removing the lower valve covers, which is why a proper PPI includes exactly that: covers off, a hand on every lower stud, because a snapped one will often move or come away in the inspector's fingers. One broken stud found early, with the engine otherwise sound, is a top-end job at $6,000โ10,000 depending on how much else is done while it is apart; the same fault discovered after purchase is the same bill without the discount. The stud check is the single highest-value line item in any PPI on a G-series car.
Valve guides are the second check, and the 3.2 is the worst offender, with the 3.6s behind it and the SC least affected. The mechanism is wear, not breakage: the guide bores widen, the valve stems rock, the stem seals cannot control oil against a moving stem, and consumption climbs. Porsche's own period tolerance allowed about a quart in 600โ1,000 miles โ these engines were never oil-tight in the modern sense โ but a quart every 300 miles, a blue haze on the overrun after a long downhill, and plugs that oil-foul on the same cylinders every service are a worn top end, full stop. There is no additive fix; the cure is the top-end rebuild at $7,000โ12,000. This is why the consumption history is a document, not a question: a seller who has owned the car for years and cannot say how much oil it uses either has not been paying attention or has, and dislikes the answer.
Timing chains and tensioners are the third. The cam chains run in housings at the back of the engine, tensioned originally by spring-and-oil units that can collapse with age, letting the chain slacken โ heard as a rattle from the chain housings, worst at idle and start-up, and fatal to valves if a chain ever jumps. The factory's own answer, the pressure-fed Carrera tensioner conversion, is a visible upgrade (oil lines feeding the housings) that most surviving cars have received; a car still on original tensioners is not a reject, but the conversion, at roughly $800โ1,500 fitted, belongs in your first-year budget and in the negotiation. The plastic chain ramps inside age and are renewed when the engine is open for other work.
Oil leaks are not a fault so much as a condition of the design, and the skill is grading them. The known sources, roughly in order of cost: the oil return tubes, whose seals perish (a modest job โ collapsible replacement tubes exist precisely because the originals need the heads off); the oil-pressure sender and thermostat O-ring at the top of the engine, which leak down the back of the case and mimic worse faults; valve-cover gaskets; crankshaft seals; and, on 964s, the head-to-cylinder joint. A dry-sump Porsche that leaves a few spots after a run is a normal old Porsche. A car that drips steadily at idle, or smells of burning oil in the cabin โ oil reaching the heat exchangers โ has leaks priced by access, and access means engine-out. Budget $1,500โ4,000 for a proper re-seal campaign, and note the tell: a freshly steam-cleaned engine underside on a car with no recent engine work in the file is a question, not a feature.
The 993's secondary air system deserves its own paragraph because it is the fault most likely to be minimised by a seller. Carbon clogs the air passages in the heads; the system cannot flow enough air at cold start; the check-engine light sets. In a state with emissions inspection that light is a failed inspection; everywhere, it is evidence about how the car has been used โ short trips, low miles, long storage โ and the full cure is top-end work. Price it as such, or require it fixed and documented before completion.
Rust and the body: galvanising changed everything, eventually
The rust story splits cleanly by year. Cars before the mid-seventies phase-in of galvanised panels โ the whole body was treated by the end of the decade โ rust like any other seventies car: structurally, and from the inside out. A 1974โ76 car needs the full forensic treatment this section describes. An SC or later car has a galvanised shell that resists rot remarkably well, and on those cars rust usually means accident damage repaired with unprotected metal, a blocked drain left for a decade, or a salt-state car stored wet. Either way, the geography of 911 rust is fixed, because it follows the water and the road dirt:
The kidney bowls and rear inner wings. Behind each rear wheel, the inner wing forms a bowl โ named for its shape โ where the wheel throws mud and water against the body. The bowls rot from inside the wheel arch outward, and because the area hides behind the wheel and the sill end, it is the rust listing photographs never show. On a lift, with the rear wheels off, it is plain. Repair is cutting out and fitting repair panels, $1,500โ3,500 a side done properly with paint, and it is structural enough that a car rotten here is a project whatever the adverts say.
The sill ends and jack points. The outer sills are stout, but the ends โ where they meet the rear wheel arch and the front wing โ trap dirt, and the jack-point reinforcement inside the sill corrodes. Press along the sills, look up at the ends from underneath, and be suspicious of thick, fresh underseal localised exactly there. The jack points are strong when sound; a sill that crumples or creaks under its own jack has told you its structural truth.
The front of the car: battery box, fuel-tank support and the front pan. The battery sits in the front luggage compartment, and acid plus water rot the tray and the sheet metal beneath it, including the front suspension pan. Lift the carpet and the spare wheel in the front trunk of every car you inspect: the tank support panel and the pan beneath the battery are visible from above and below, and perforation here is a safety failure in spirit everywhere, priced at $1,000โ2,500 to cut out and replace properly. Headlamp bowls and the lower edges of the front wings trap mud; bubbles at the bottom of a wing behind the wheel are the same story as any car of the era.
Door bottoms, the windscreen surround and the open cars. Doors fill with water when their drains block, and the bottom seams swell and bubble. The windscreen aperture rusts under its seal, worst at the lower corners, announcing itself as a damp front carpet and a misting screen โ on a galvanised car it points to a replaced screen fitted badly or a seal past its life. Targas add the roof-panel and roll-bar seals; Cabriolets add the rear window, top frame pivots and scuttle drains. On both, water that gets in goes to the floor pans and rear seat wells: lift every carpet you can, and press the pans for the crunch of scale under sound-looking paint.
Accident damage matters as much as rust, because today's values justify repairing damage that would have written a car off in 2005 โ and justify hiding it. Look for uneven gaps at the front trunk lid, replaced front panels (spot-weld patterns differ), and overspray on the front-compartment seals and wiring. A car with a front corner replaced well is a usable car at the right price; a car with a pulled, rippled inner structure is not, and the difference is what the lift inspection and a paint-depth gauge are for.

Suspension, steering, brakes โ and the cost of sitting still
The G-series suspension is torsion bars front and rear, and its faults are the faults of age and rubber. Torsion bars sag and occasionally snap (a corner suddenly low is a broken bar until proven otherwise), the spring-plate and trailing-arm bushes perish and let the rear geometry wander, and the dampers โ Bilstein or Boge from the factory โ are wear items long past their design life on any unrestored car. A full refresh with bushes, dampers, alignment and corner-weighting runs $3,000โ6,000 at a specialist and transforms the car; it is the most satisfying money in air-cooled ownership after the engine itself. The 964 and 993 use coil springs and power steering โ racks leak, pumps whine when low, and the 993's multi-link rear axle has links and bushes whose wear shows as looseness under power and uneven rear tyre wear, $2,000โ4,000 to renew comprehensively. Steering on a G-car is unassisted and should be light, direct and free of straight-ahead play; play is usually rack bushings or the column's universal joint, both modest.
Brakes are discs all round, and the standard old-car list applies: calipers seize from sitting, hoses perish internally and act as one-way valves, discs lip and corrode. A full hydraulic refresh is $1,500โ3,000 and is not optional on a car that has stood. The standing-still point generalises: these cars tolerate mileage far better than storage. A 120,000-mile SC driven weekly will need less in its first year than a 60,000-mile car that has sat for six years, because sitting perishes every seal, gums the CIS or the injectors, and corrodes the brake and fuel systems from inside. The recommissioning bill for a long-stored car โ fuel system cleaned end to end, brakes rebuilt, all fluids, tyres, battery, belts and hoses โ is $4,000โ8,000 before anything is improved, and it belongs in the price you offer.
Electrics, heating and the cabin
The electrics are simple by modern standards and fail at the usual places: earth straps, fuse contacts in the front-compartment fuse box (clean them before diagnosing anything), alternator brushes and regulators, and the starter solenoid in the heat above the gearbox. The heating system deserves its own warning: cabin heat is exhaust heat, collected by heat exchangers around the exhaust manifolds and ducted forward. When the exchangers rot โ mild steel in the path of road water โ the risks are a cabin that smells of exhaust and, in the worst case, carbon monoxide; when the control flaps and cables seize, the heat is simply on, permanently. New exchangers are $800โ1,800 a pair in parts depending on generation, plus fitting, and any car whose cabin smells of exhaust at idle with the heat on is grounded until they are checked. Period air conditioning is marginal when perfect, and most cars' systems are incomplete or inert; price a car as if the A/C does not work unless it demonstrably blows cold, and budget $1,500โ3,000 to make an intact system genuinely cold with modern components.
Inside, the costs are trim-shaped. G-series dashboards crack across the top in sun states โ a recover-or-replace decision at $800โ2,000. Seat bolsters wear through on the driver's side and sport-seat foam collapses; a quality leather retrim runs $4,000โ8,000 for the front pair, which is why sound original interiors carry their premium. The 964 and 993 cabins age better but add electronics: climate servos and control heads, window regulators, and on the 993 the immobiliser modules that can strand the car expensively when their fobs are lost โ two working fobs and the code card are part of a complete 993, and their absence is a price chip. Targa panels rattle and leak at their seals; a rebuild with new seals is $600โ1,200 and worth every cent on a car you will drive in weather.
How to inspect one
Inspect an air-cooled 911 in two passes: your own, to decide whether the car deserves the second, and a specialist's pre-purchase inspection (PPI) on a lift, which is where the money is protected. Your pass takes an hour and a torch; the PPI costs a few hundred in shop time and returns leak-down figures, a stud check and an underside verdict in writing. No seller of a good car refuses a PPI at the buyer's expense. A seller who does has completed your inspection for you.
- Paperwork and identity first. Match the VIN on the title to the stamping in the front luggage compartment and the plate in the door jamb or A-pillar. Check the engine number against the type the car claims to be โ it is stamped on the crankcase at the fan support, and a mismatched engine in a G-series car is a major value fact, not a footnote. Then read the history file: you are looking for engine work (studs, guides, tensioners), clutch and gearbox invoices, and a service rhythm, not a single heroic bill from the month before the sale.
- Cold start, arranged in advance. Insist the engine is stone cold when you arrive and stand behind the car for the start. A puff of blue that clears in seconds on a car that has sat is normal dry-sump behaviour. Smoke that persists, or that returns on the overrun during the drive, is valve guides or worse. Listen at idle for the chuffing tick of a leaking head joint โ the stud fault โ and for chain rattle from the housings at the back of the engine.
- Oil, read the air-cooled way. With the engine warm and idling on level ground, check the level in the tank: it should sit between the marks, and the oil should not smell of fuel or look like mayonnaise. Then ask the consumption question and write the answer down: a quart per thousand miles is period-normal; a quart per three hundred is a top-end rebuild introducing itself.
- Under the car, or do not buy the car. On the PPI lift: kidney bowls, sill ends and jack points, battery box and front pan, floor pans, and the engine's underside for the grading of its leaks. Perforation in the bowls or the front pan is structural and reprices the car as a project. This step, with the wheels off, is the one your own driveway inspection cannot replace.
- The stud check. Ask the PPI shop to remove the lower valve covers and check every lower head stud by hand, and to report it in writing. A snapped Dilavar or a stud that moves is the top-end conversation from the problem section, priced before the car is yours rather than after.
- Compression and leak-down. Compression alone is a blunt instrument on these engines; leak-down is the test that localises the loss โ past the rings, past a valve, or past the head joint. Even numbers in the healthy range across all six cylinders are what you are buying. One low cylinder is not a negotiating detail; it is a diagnosis you are about to pay for.
- The gearbox, cold. Drive away gently and make the first change into second within the first half-mile: a crunch or a baulk on a cold 915 or G50 is worn synchromesh showing itself before the oil thins and hides it. Check every gear for noise under load and on the overrun, and reverse for crunching. On a Tiptronic, hold it against the brake in drive and reverse and feel for shunting or delay.
- The test drive, long enough to get hot. Twenty minutes minimum, including a sustained higher-speed stretch. The car should track and brake straight with a firm pedal, and hold steady oil pressure and temperature. Watch the temperature in traffic afterwards: cooling is the fan and the oil, and a car that creeps hot at idle has a fan, belt, oil-cooler or debris problem โ air-cooled engine compartments collect leaves and worse around the cylinders, and a PPI should include a look under the fan shroud's edges.
- Heat on, whatever the weather. Run the heater fully hot and smell the cabin air: exhaust smell means heat exchangers, and that car does not get driven home. Work the blower on all speeds, and on 964s and 993s run the climate control through its full range, hot to cold, and test the air conditioning's actual output temperature rather than its intentions.
- Electrics and the small things. Every window, the sunroof or Targa panel, wipers, washers, lights, horn, gauges โ and on a 993, both immobiliser fobs, locking and unlocking, more than once. Electrical faults on these cars are individually cheap and collectively diagnostic: a car where everything works has been maintained by someone who fixed things when they broke.
- Stance and steering. Stand back and look: level side to side, the correct slight rake, no corner sitting down. On the road the steering should be free of straight-ahead play and the car should not wander or tramline beyond what wide rear tyres explain. Rear-end looseness under power on a 993 points at the multi-link bushes; a sagging corner on a G-car points at a torsion bar or its adjustment.
- Interior last, and honestly. Sit in the driver's seat and feel for collapsed foam and a frame through the bolster; look at the dash top in raking light for cracks; lift every carpet the seller allows and press the floors; operate the Targa or Cabriolet top through its full cycle yourself. A sound original interior is the hardest part of these cars to recreate at any price, and it is the part you will look at every mile you drive.
Values
The market block beneath this guide carries the current numbers โ what is listed now, and what recorded sales have achieved โ and this section teaches you how to read them, because with air-cooled 911s the spread inside a single model line is wider than the spread between model lines. A tired SC and a freshly rebuilt one share a badge, a year and a silhouette, and they are not the same car at two prices; they are two different purchases. Read every figure through the condition of the specific car, and treat the gap between the cheapest and dearest examples of any variant as the market's own estimate of what the work costs โ an estimate that, on engine work especially, tends to flatter the cheap car.
Three premiums are durable and rational. The first is for the G50 gearbox in a 3.2 Carrera: the market pays it because the driving difference is real and the supply of 1987โ89 cars is fixed. The second is for documented engine work โ a top-end rebuild with studs addressed, tensioners converted, guides renewed, invoiced by a known specialist. Paperwork of that quality routinely adds more than the work cost to a car's value, because it removes the largest unknown in the purchase. The third is for originality in the cars where collectors set the price: matching numbers, original colours confirmed by the build record, unmodified Turbos and the limited cars โ Speedster, RS America, the wide-body 993s โ where a changed specification subtracts value that no quality of workmanship adds back.
Against those, the discounts are equally systematic. Targas and Cabriolets trade below coupes of the same year and condition โ the value route into every generation if the open car suits you. Tiptronic 964s and 993s sit below their manual equivalents by a margin that overstates the difference in the driving. High mileage, honestly documented and continuously maintained, is discounted more than it should be on engines that tolerate miles better than storage โ the cheapest good air-cooled 911 is often the well-kept high-miler, and the most expensive cheap one is the low-mileage car that has sat for a decade. Colour moves prices at the margins: the period reds, blacks and silvers are the liquid colours, while brown or gold cars need the right buyer โ allow for a longer sale, not a lesser car.
On negotiation, asking prices are frequently aspirations set by the dearest recent sale of a better car. Auction results โ the achieved figures in the market block โ are the honest comparator, and the distance between an asking price and the auction evidence for genuinely comparable cars is the negotiation, conducted with the PPI report in hand. Price the faults you have found at retail shop rates, present the numbers, and be prepared to walk: the supply is deep and another car is always coming. What never pays is buying the cheap example of an expensive variant. The project Turbo, the rusty early 2.7, the 993 with the check-engine light and no history โ each costs its premium sibling's money to put right and remains the lesser car at the end of it.
Parts and ownership
The air-cooled 911 is one of the best-supported classics in the world, for a structural reason: Porsche built the same basic car for a quarter of a century, the factory's classic programme still supplies an unusually deep catalogue, and the aftermarket treats every generation in this guide as current business. Almost nothing is truly unavailable. The ownership questions are price and lead time, not existence.
Easy and reasonable: service consumables, filters, plugs (twelve on a 964, priced accordingly), brake discs, pads, caliper rebuild kits and hoses, dampers, bushes, clutch kits, engine gaskets and seals, valve-cover hardware, ignition service parts, CIS and Motronic sensors and relays, exhaust systems in standard form, glass and most seals, and tyres in the period sizes โ the 15- and 16-inch fitments of the G-series are still made by more than one manufacturer, which was not true a decade ago and transforms the usability of the cars.
Dearer, and worth planning for: engine work is the headline โ a full rebuild of a G-series six by a known specialist runs well into five figures, and a top-end refresh is the job priced in the engine section. Gearbox rebuilds follow the same pattern. Heat exchangers are a significant parts bill. 993-specific items โ Varioram components, secondary-air hardware, climate parts, immobiliser fobs and modules โ carry last-of-the-line pricing. Trim is the quiet expense: dashboards, seat recovering in correct materials, Targa panel rebuilds and Cabriolet tops all cost what skilled hand-work costs. Body panels exist for every generation, including repair sections for the kidney bowls and front pans, but the labour of fitting them properly is the bill, as on every classic.
Running one. Budget for a specialist service rhythm: oil services are frequent by design (the oil is half the cooling system, and it works hard), G-series valve clearances are a periodic skilled job, and an annual inspection by someone who knows the cars catches small faults โ a weeping return tube, a perishing fuel line โ while they are still small. Fuel lines deserve a sentence of their own: ethanol-era fuel and forty-year-old rubber are enemies, a full set of modern-specification lines is cheap insurance, and it belongs on the first-year list of any car without a recent invoice for them. Insurance through a classic policy with an agreed value is standard and modest. Fuel consumption in the high teens to low twenties is normal. The realistic first-year budget for a good, honestly bought car is a few thousand; for a car bought cheaply against this guide's advice, it is the difference you thought you saved, with interest. Storage matters more than mileage: a dry garage, a battery conditioner, and regular full-temperature use are the cheapest maintenance there is, because the faults of the stored car are the expensive ones.
Which one to buy
- The all-rounder: 911 SC coupe. Galvanised shell, the durable 3.0, simple specification, deep supply. If you want one air-cooled 911 to drive for a decade, the SC is the rational heart of the range, and a good one leaves budget in hand for the suspension refresh that makes it superb.
- The value buy: a Targa or Cabriolet, in any generation. The market discounts the open cars against coupes year for year, condition for condition. If you will drive in fair weather and keep the car under cover, the discount is the market paying you to take the roof off.
- The driver's pick: Carrera 3.2 with the G50. The developed G-series with the better gearbox โ the car most experienced owners name first. Pay the premium for the gearbox and for documented top-end work, and test the synchromesh cold before you pay for either.
- The modern classic: 993 Carrera. The last air-cooled car, with the sixth gear, the multi-link rear end and the looks. Buy it on leak-down numbers, consumption history and a working secondary-air system, and keep both immobiliser fobs somewhere safe.
- The connoisseur's car: 964 Carrera 2. The thinking buyer's 3.6 โ coil springs, power steering, twin plugs, and a market that has only recently woken up to it. An early car needs its head-sealing history read carefully; a sorted one is the connoisseur's bargain of the range.
- The brave buy: an early 2.7, with the engine work already done. The lightest, rawest G-car and the cheapest entry โ but only, ever, with invoices proving the case has been machined and the studs addressed. Without them it is not a brave buy; it is an unscheduled rebuild.
- The collector car: the Turbo, the Speedster, the RS America. Bought on originality and paperwork, inspected by a specialist in the variant, and priced by a market that punishes modification. Wonderful cars; a different discipline from everything above.
And the rule that overrides all of the above: buy the car with the documented engine, the sound shell and the specialist's PPI in writing โ in the specification you can live with, not the one you dreamed about. Gearboxes, brakes, dampers and trim are all fixable at prices you can plan for. A rotten shell and a tired engine are the two bills that exceed the car's value, and they are the two things this guide has taught you to test before the money moves.
See the 23 911 cars currently listed.
