MG midget buyer's guide
MG midget -- the model's own buyer's guide: variants, values and what to check.
Years listed: 1966-1979 Β· Series: Midget
Overview and history
This is the model guide to the MG Midget, and it goes one level deeper than the series guide beside it. Where that guide walks the whole range in outline, this one stays with the individual variants β the Mk I 948, the Mk I and Mk II 1098s, the Mk III 1275 in its square-arch and round-wheel-arch forms, and the Triumph-engined 1500 β because on a Midget the variant is not a trim detail. It decides the engine you are buying, the gearbox bolted to it, the rear springs under it, the carburettors on it, and the checks that will make or break the purchase. Two cars that look near-identical in a photograph can be separated by a decade of development, a different engine family, and a four-figure difference in what the next year will cost.
The outline, briefly. The Midget was built at Abingdon from June 1961 to December 1979, about 226,000 cars in all, as MG's version of the Austin-Healey Sprite β the pair known as Spridgets, built side by side, mechanically identical, separated by grille, badges, trim and price. It is a unitary steel shell with no separate chassis. The engine for the first thirteen years is BMC's A-series four, growing from 948 cc to 1,098 cc to 1,275 cc. Front suspension is independent, built around a kingpin upright; the rear is a live axle on leaf springs β quarter-elliptic on the earliest cars, semi-elliptic from the Mk II. And two facts settle many listing arguments: no Midget was ever built with an automatic gearbox, and no Midget was ever offered with overdrive. Every car here is a four-speed manual. If a listing describes an automatic Midget, the listing is wrong, not the car β aggregated listing data for this model does exactly that.
Our own pool shows why a variant-level guide earns its keep. We currently track 19 Midgets, all for sale and all sourced from Facebook Marketplace sellers, spanning 1966 to 1979: two cars from 1966, one from 1970, three from 1973, two from 1974, and the remaining eleven from 1975 to 1979. The pool contains no 948 and no Mk I of any kind, a single early square-arch 1275, a handful of prized late chrome-bumper cars, and a clear majority of 1500s. That is the shape of survival, and red β 8 of the 19 cars β is the colour survivors wear most often, ahead of green and white at 3 each. A buyer shopping today is usually shopping for a 1500 or a late 1275, and this guide weights its detail accordingly, while still covering the early cars properly.
These were inexpensive cars, bought young, driven hard and parked outside. The mechanical parts are simple, tough and still made in depth; the shell is the opposite, and structural rust is the one fault that reliably costs more than the finished car is worth. The variant decides what to check; the shell decides whether to buy.

The models
Every Midget is a two-seat open roadster on the same basic unitary shell, and the range divides along three axes: which engine, quarter- or semi-elliptic rear springs, and chrome bumpers or rubber. There were no factory coupΓ©s, no GT version and no bigger-engined flagship. What follows is the variant-by-variant record β what changed, when, and how you tell one car from the next.
| Model | Years | Engine | Output | Built | Character |
|---|---|---|---|---|---|
| Midget Mk I 948 | 1961β1962 | 948 cc A-series (9CG) | 46 hp | 16,080 | The original; sidescreens, drums all round, quarter-elliptics |
| Midget Mk I 1098 | 1962β1964 | 1,098 cc A-series (10CG) | 56 hp | 9,601 | Front discs arrive; the small-main crank is the weak point |
| Midget Mk II 1098 | 1964β1966 | 1,098 cc A-series (10CC) | 59 hp | 26,601 | Wind-up windows, semi-elliptics, the strong 2-inch-main engine |
| Midget Mk III 1275, square arch | 1966β1971 | 1,275 cc A-series (12CC family) | 65 hp | 22,415 to the 1969 facelift | The sweet spot arrives; attached folding hood |
| Midget Mk III 1275, facelift and round arch | 1970β1974 | 1,275 cc A-series | 65 hp UK; US cars progressively less | 77,831 | Black-trim facelift, then the prized round-arch cars of 1972β74 |
| Midget 1500 | 1974β1979 | 1,493 cc Triumph (Spitfire) | 65 hp UK; about 53 hp US | 73,899 | Rubber bumpers, raised ride height, Triumph gearbox |
(Outputs are period home-market figures; US cars fell away as emissions equipment arrived β the US 1275 ended in the mid-50s net, the US 1500 at about 53 hp. The Mk III rows split at the 1969 facelift.)
Reading the chassis number: the GAN prefixes. A Midget carries its identity in its chassis prefix, and the six prefixes are the most useful identification skill in this guide. GAN1 is the Mk I 948, from June 1961. GAN2 is the Mk I 1098, from October 1962. GAN3 is the Mk II, from March 1964. GAN4 is the early Mk III 1275, from October 1966. GAN5 is the later Mk III, from the 1969 facelift through the last chrome-bumper cars in 1974 β the round-wheel-arch cars are GAN5s, identified by their arches and date, not by a separate prefix. GAN6 is the 1500, from October 1974 to December 1979. The engine carries its own prefix plate, and the pair settle almost every identity argument: 9CG for the 948, 10CG for the early 1098, 10CC for the Mk II 1098, the 12CC family for the 1275, and a Triumph number on the 1500. A car whose prefixes disagree has had an engine swap β common, often enjoyable, and to be priced as what it is.
Mk I 948 (June 1961 to October 1962), GAN1. The Sprite Mk II in MG dress, and basic: no external door handles or locks β you slide the Perspex sidescreen and reach through to the catch β a packaway hood of sticks and fabric stowed in the boot, an optional heater, and 7-inch drum brakes all round. Quarter-elliptic rear springs cantilever from the rear bulkhead, with trailing radius arms locating the axle. The 948 (9CG) makes 46 hp through twin SUs, via the early smooth-case gearbox. These are the rarest and slowest Midgets, and their value lives in originality: sidescreens, correct trim and an unmodified shell are what you are paying for.
Mk I 1098 (October 1962 to March 1964), GAN2. The engine grew to 1,098 cc (10CG), output rose to 56 hp, and front disc brakes replaced the front drums β but the 10CG kept the 948's crank dimensions, with 1.75-inch main journals where the later 10CC grew them to 2 inches, and crank breakage on hard-used engines is a period fact, not folklore. Everything else β sidescreens, packaway hood, quarter-elliptics β is Mk I. On a GAN2 the bottom end is the negotiation: a documented rebuild is worth real money, and a rumble at a hot idle is an engine-out job.
Mk II (March 1964 to October 1966), GAN3. The Mk II civilised the Midget without softening it: wind-up windows in proper doors with external handles and locks, a taller windscreen, a hood on a folding frame, a lockable boot, and semi-elliptic rear springs calming ride and handling. The engine stayed at 1,098 cc but became the 10CC: mains enlarged to 2 inches, compression 8.9:1, output 59 hp. Many internals do not interchange between 10CG and 10CC, so the prefix matters when you value the car and again when you order parts. The Mk II is the strongest small-engine car and, for many drivers, the best-balanced Midget of all. The two 1966 cars in our pool are this specification.
Mk III 1275, square arch (October 1966 to 1969), GAN4. The 1275 is the engine the Midget deserved from the start: a relation of the Mini Cooper S unit in a single softer specification β 65 hp, with torque the small engines cannot match β through the ribcase gearbox. The hood became an attached folding design one person can raise in under a minute, and US cars from 1968 carry the padded dashboard and the first emissions hardware. The rear arches are the original squared-off profile, and that one pressing separates a GAN4 or early GAN5 from the cars the market prizes most.
Mk III facelift (1970) and the round-wheel-arch cars (late 1971 to 1974), GAN5. The 1969 facelift for 1970 is a trim event: black grille, black sill finishers, Rostyle wheels, over unchanged 1275 mechanicals β though American emissions tune arrived in stages, so a US car of 1973 is softer than one of 1968. Then, from late 1971 for the 1972 model year, Abingdon re-cut the rear arches to a round profile. The round-wheel-arch cars β RWA in the advertisements β were built for barely two years before the shell reverted to square arches in 1974. They combine the best engine, chrome bumpers at the original height and the prettiest rear quarter the Midget wore, and the market prices them at the top of the mainstream range. Verify the arch before paying: check both sides for a true round cut rather than a square arch trimmed toward round, and look inside for pressing lines and repair panels. The premium rides on shaped steel; make sure it is factory steel.
Midget 1500 (October 1974 to December 1979), GAN6. In October 1974 the Midget changed more than in the previous thirteen years combined. American rules demanded 5 mph bumpers and higher headlamps, so the car gained full-width black polyurethane bumpers and was raised on taller springs β the visual tell is the generous gap between tyre and arch no chrome-bumper car has. The A-series could not be stretched beyond 1,275 cc, so British Leyland fitted the 1,493 cc Triumph engine and its all-synchromesh single-rail gearbox from the Spitfire. Home-market cars got twin SU HS4s and about 65 hp; US cars got a single Zenith-Stromberg, 7.5:1 compression, an air pump and recirculation, and β from 1976 in California and later federally β a catalytic converter, for about 53 hp. Production ran five full years, which with survival explains the pool: eleven of our nineteen cars date from 1975 onward, four of them from 1979. The 1500 is the Midget you will actually find for sale, and its engine carries the signature weakness β crankshaft thrust washers β that the rest of this guide returns to.

Engines and gearboxes
The small A-series: 948 and 1098, and the crankshaft divide
The A-series is one of the great small engines β an overhead-valve four from the early 1950s, built in the tens of millions, and so thoroughly understood that there is no fault on one the trade has not seen a thousand times. In the Midget it sits upright and longitudinal, breathes through twin SUs, and drives a separate gearbox. What separates the small variants is not character β all are sweet and simple β but their bottom ends, and the bottom end is where your inspection concentrates.
The 948 (9CG, 1961β62) makes 46 hp: smooth and slow in the best sense, cruising at 60 mph and asking for planning on hills. Its crank runs in 1.75-inch mains, adequate at 46 hp. Judge it as you judge every A-series: strong oil pressure hot at speed, no blue smoke under load, no emulsion under the filler cap.
The early 1098 (10CG, 1962β64) makes 56 hp on the same 1.75-inch-main crankshaft, and that is the whole story of the engine. The extra output loads a crank sized for the 948, and hard use finds the margin. The failure mode is fatigue cracking, announced late β a deep rumble under load at a hot idle, oil pressure sagging as the oil thins β and the cure is an engine-out rebuild at roughly $3,500β6,000. No cheap test proves a 10CG crank sound from outside, which is why history matters: a bottom-end invoice, strong steady hot oil pressure and quiet running under load are the evidence you are buying. A 10CG with a rumble is priced as a rebuild with a car attached.
The Mk II 1098 (10CC, 1964β66) is the corrected engine: mains grown to 2 inches, compression 8.9:1, output 59 hp, the crank weakness gone. Internals differ from the 10CG across much of the engine, so never order 1098 parts by capacity alone β quote the prefix.
Across all three, the shared checks are these. Oil pressure first: a needle that fades badly as the engine warms is worn bearings or a worn pump, not character. Smoke second: blue smoke on start-up that clears is valve-stem seals; smoke that persists under load is rings and bores; emulsion under the filler cap with coolant loss is a head gasket. Noise third: the rocker shaft and rockers wear oval and produce a tappety clatter no clearance adjustment fully cures, because the clearance you set at rest is not the clearance the worn geometry runs at β a rebuilt rocker assembly is a few hundred dollars in parts. Timing chains stretch and rattle at idle; the chain is cheap and a half-day job, and a silent chain on a high-mileage engine usually means someone has already been inside.
Oil leaks are the A-series' public reputation and the most misread evidence on a viewing. The rear of the crank is sealed by a scroll β an Archimedes-screw thread machined into the crank that winds oil back into the sump as it turns β not by a lip seal. It works when the engine breathes freely; it leaks when crankcase pressure rises, which happens when the breather blocks or the rings tire. A drip from the bellhousing drain hole is therefore a symptom, not a seal to replace: a few spots after a run are period normal, a spreading pool with oil consumption is blow-by telling you the bores are worn. Check the breather before condemning any A-series β a blocked breather manufactures this leak on a sound engine. Timing-cover seals, rocker-cover gaskets and the fuel-pump joint all weep with age and are cheap routine items.
Carburation is twin SUs throughout the A-series years: the 948, both 1098s and the 1275 wear twin SU HS2 carburettors of 1ΒΌ inches. The Frogeye Sprite's tiny H1 instruments belong to the car before the Midget β H1s on an early Midget are a substitution, not the factory specification. The HS2's wear point is the throttle spindle and its bushes: worn spindles admit unmetered air, the idle wanders and will not set, and no needle-swapping cures a leak downstream of everything you can adjust. Wiggle each spindle: play you can feel is wear that matters. Re-bushed or exchange carburettors run $400β800 for the pair. Dashpot oil is the other free check β a dry dashpot lets the piston rise too fast, the mixture weakens, and the car stumbles in a way owners blame on ignition.
The 1275: the Cooper S relation, in its two market tunes
The 1275 (GAN4 and GAN5, engines of the 12CC family) shares its architecture with the Mini Cooper S unit β the largest production A-series, a stronger crank in generously sized bearings β but in the Midget it is a single, softer specification: 65 hp at 6,000 rpm and 72 lb-ft of torque, no Cooper exotica, tuned for longevity. That softness is a virtue in a used car: the 1275 is understressed, famously durable, happy to rev, and carries the deepest parts and tuning support of any engine here.
Its carburation is twin SU HS2s, re-needled for the bigger engine, so the spindle and dashpot checks above apply unchanged. What changes with the years is the equipment around them: US cars progressively gained an air pump, a gulp valve, evaporative controls and leaner needles, and by the mid-1970s the US rating had fallen into the mid-50s net. A late US 1275 that feels flat may simply be running its factory tune; a de-smogged car on UK needles is common and effective β but in an inspection state the missing equipment can be a registrability problem, so establish what is under the bonnet today. Never judge a US 1275 against a UK road-test figure; judge it against another US car of the same year.
Its specific checks add three items. Cooling first: the radiator is small and marginal in southern summers, and a 1275 that runs hot in traffic usually has a silted core or a tired water pump rather than a gasket failure β but repeated overheating warps heads, so a gauge living above normal is a reason to test, not to shrug. A re-cored or new radiator is $250β450. Second, its performance tempts harder use, so bore wear arrives earlier. Third, it works its clutch and synchromesh harder β engine and gearbox checks are one conversation.
The Triumph 1500: torque, three bearings, and the thrust washers
The 1,493 cc engine in the 1500 is not an A-series and shares no part with one. It is Triumph's overhead-valve four from the Spitfire, fitted because British Leyland owned both companies and the A-series could grow no further. It is an all-iron, three-main-bearing engine whose stroke is far longer than its bore, and those facts define it: strong low-down torque, a disinclination to rev, a coarse note, and rod bearings that are a consumable at sustained high revs. In UK form, on twin SU HS4 carburettors of 1Β½ inches and 9:1 compression, it makes about 65 hp. In US form β a single Zenith-Stromberg 150 CD with a water-heated automatic choke, 7.5:1 compression, air pump, recirculation and, on later cars, a catalytic converter β it makes about 53 hp and feels it. The common, effective conversion is the European specification: twin HS4s, the matching manifold and exhaust, and higher-compression pistons when the engine is next apart. Judge any US 1500 first by establishing which specification is fitted today; the two drive like different models.
Then do the check this engine is famous for. Crankshaft thrust washers control the crank's fore-and-aft movement: two semicircular washers at the centre main bearing take the thrust load every time the clutch goes down. As they wear thin, endfloat grows; past a point a worn washer is no longer retained in its recess and drops into the sump. From that moment nothing controls endfloat at all. The crank walks fore and aft with every press of the clutch, its thrust faces machining directly against the block and cap β iron against iron, under load, thousands of times. The engine destroys its own crank and block, sometimes within a few hundred miles, while still running well enough to sell. The washers cost a few dollars; the check costs nothing. Engine off, lever the front pulley gently fore and aft, or watch it while a helper works the clutch. Correct endfloat is a few thousandths of an inch β barely feelable. Visible movement, or a clunk, means the washers are worn or gone. Caught early, the job is sump off and new washers, pinned by some specialists so they cannot drop again: $400β900 at a shop. Caught late, it is a rebuild at $3,500β6,000 or a replacement engine. Believe a claim the washers were done only with an invoice. Two habits preserve them: never sit at lights with your foot on the clutch, and start in neutral, foot off the pedal, so the thrust faces are not loaded dry before oil pressure arrives.
Beyond the washers, the faults are ordinary. The Zenith-Stromberg's rubber diaphragm perishes and splits, giving flat running and a mixture that will not set β a small-parts job, and the first suspect on a car that will not tune. The water-heated automatic choke sticks, giving rich running and a fast idle that never settles. Treat one combination as urgent: a rich-running US car with air pump and converter still fitted can overheat the converter with unburned fuel, and the period under-bonnet fire stories trace to exactly this β a fix-this-week car. Cooling is by a larger radiator than the A-series cars, with an electric fan on later cars; a 1500 that boils usually has a silted core, a failed fan switch or a stuck thermostat, all cheap.
Gearboxes: ribcase and single-rail, and why they are not interchangeable
A-series cars use BMC's four-speed, first in smooth-case form on the earliest 948s and then the ribcase box β identified by the ribbed webs cast into its casing β to 1974. Both have synchromesh on second, third and top only. First gear has no synchromesh: a crash engagement, selected at a standstill, and a crunch engaging first on the move is correct period behaviour. A crunch into second is the classic ribcase fault β worn synchromesh β cured only by a rebuild at $900β1,800. Worn boxes also jump out of gear on the overrun and whine in the indirect gears as layshaft bearings tire. A healthy ribcase is pleasant and precise. Parts support is good but not infinite: good used gear clusters are finite, so buy the car whose box is quiet today.
The 1500 uses Triumph's single-rail four-speed β the Spitfire and Marina-family box, named for its single selector rail β with synchromesh on all four forward gears and a shorter, notchier throw. It is durable. Wear shows as second-gear crunch, layshaft whine, and a sloppy lever that is almost always worn remote-linkage bushes rather than internals β a small-parts fix. If every gear engages cleanly, price the bushes, not the rebuild.
On both boxes, the clutch is the negotiation point buyers underprice. Engine and gearbox come out together to change it, so a slipping or juddering clutch is a $700β1,300 shop job, not a cheap consumable. Judder is a worn or oil-contaminated plate β on an A-series car, check whether the oil traces to the rear scroll and a blocked breather. A sinking pedal is hydraulics; master and slave cylinders are cheap on both families.
At the back, a live axle is located by the leaf springs and, on quarter-elliptic cars, by trailing arms. A whine rising and falling with throttle is crown-wheel and pinion wear β live with it, or budget $800β1,400 for a rebuild. Clunks on take-up are worn half-shaft splines or differential play. Wire wheels carry their own check: splined hubs and wheel centres wear together, and a wheel that rocks on its hub with a metallic click is a safety item β a full set of hubs and wheels runs $1,200β2,200.

Problem areas
A Midget fails in a predictable order: the shell first, the suspension second, the electrics third, and the engine last. That is the reverse of the order most buyers inspect in, because the engine is what a seller can demonstrate in a driveway and the shell is what costs the money. Note the honest limitation: our brief for this guide carries no examined photo-note sample for these cars, so there are no incidence percentages to quote here. What follows is the marque's documented failure map, variant by variant.
Rust: the sill, spring-hanger and floor map
The unitary shell concentrates its strength in a handful of pressings, and rust attacks exactly those pressings, from the inside out. Learn the map in this order, because it is the order of structural importance.
Sills. The single most important check, on every variant. Each sill is a box section running the length of the cockpit β an outer panel you can see, an inner panel you mostly cannot, the floor edge closing the top β and it carries the car's bending strength and its jacking points. Mud and water enter at the ends and sit inside the box; the sill rots from within, and by the time paint bubbles outside, the inner structure is usually perforated too. Read sills with your hands: press hard along the full length, feel underneath for flaking, and examine both ends. Fresh underseal, fresh paint low on the car, and sill covers screwed over the originals are all the same sentence: someone has decorated the evidence. The definitive test uses the car's own jacking point, set into each sill: take the car's weight on each point in turn. A sound sill lifts silently; a rotten one creaks, flexes and begins to fold β and a seller who refuses has answered the test. Proper replacement, with the shell supported because door gaps move when the sill comes out, runs roughly $1,000β2,000 per side. A car needing both sills is a restoration project whatever its paint says.
Rear spring hangers and the rear bulkhead. The second structural trap, hidden behind the rear wheels. On semi-elliptic cars β everything from the Mk II onward, which means every car in our pool β the front of each rear leaf spring mounts in a boxed hanger pressed into the shell just ahead of the rear wheel, and the boxes trap mud against the rear bulkhead, the panel behind the seats. The assembly rots as a unit: hanger box, bulkhead and floor edge together. A hanger tearing out of a rotten box is a genuine mechanical failure, and the repair is fabrication and welding at $500β1,200 a side. Prod the boxes hard from underneath, and from inside lift the trim behind the seats and check the bulkhead's lower corners. On quarter-elliptic Mk I cars the springs cantilever from mountings high on the bulkhead instead, but the examination is the same: the mountings and the bulkhead must be sound metal. While at the back, check the arches, valance and boot floor: the boot lid seal leaks, water pools in the pressings, and the fuel tank sits in the boot floor's rear section, rusting from the top where you cannot see it. A new tank is $250β400, and flakes from a dying tank will block filters and jets for exactly as long as you refuse to replace it.
Floors, footwells and the front bulkhead. Water enters past the windscreen seal, door seals and heater intake, and sits under the carpets and felt, which hold it against the pans like a sponge. Lift every carpet β two minutes, no tools β and treat glued-down carpets as a decision about what you may see. Surface rust is a clean, treat and paint job; perforation at the floor edges, where the pan meets the inner sill, is structural and belongs in the sill budget. The front bulkhead and footwell sides rot at their lower edges, and the front crossmember under the radiator rusts on neglected cars, visible only from underneath with a torch. Together these separate a shell needing local repairs from a shell needing a jig β and the second car is worth a fraction of the first.
A-posts, doors, bonnet and scuttle. The A-post rusts at its base where it meets sill and front wing: open the door fully and swing gently on it β a post that flexes is a structural repair in a trim problem's clothes. Door bottoms fill through blocked drain slots and rot along the lower edge: run a fingertip along every door bottom and confirm the slots are open. The bonnet rusts along its front edge and dents easily; the scuttle and windscreen frame rust quietly under bright paint. Headlamp bowls, valance and grille surround are cosmetic money β but count them, because small panels plus paint add up.
The battery tray rots from acid above and road water below, invisibly, under the battery itself: rock the battery, look at the tray edges and the bulkhead below with a torch, and treat a sound tray as a character reference for the whole car.
The pattern to internalise is that rust on a Midget is a system, not a spot. One bubbling arch on a car with sound sills, hangers and floors is a fine buy; shiny paint over soft sills is a restoration project in a driver's clothes, and the welding bill decides everything. There is no cheap Midget that stays cheap.
Front suspension, steering and brakes: the kingpin front end
The front suspension is a 1950s Morris and Austin design: coil springs and double wishbones, the upper wishbone formed by the arm of the Armstrong lever-arm damper, and the wheel turning on a kingpin β the factory calls it a swivel pin β in a forged upright. Every variant, 948 to 1500, steers through the same arrangement and suffers the same neglect.
The kingpin and its bushes wear if the grease gun is neglected β the nipples want attention roughly every 3,000 miles, a schedule that lapsed decades ago on most survivors. Worn kingpins give play at the wheel, vague steering, knocks and tyres worn on one edge. The check is precise: jack the car, grip the front wheel top and bottom, and rock it. Play that disappears when an assistant presses the brake pedal is wheel bearings, because clamping the disc stills the hub β cheap. Play that remains is kingpin and bush wear, a press-and-ream job at $400β800 a side. One warning: do not let a seller grease a dry, knocking front end on the morning of your viewing and call it cured β grease quietens a worn kingpin for about a week.
The lever-arm dampers leak at their shaft seals and lose damping as the oil goes: push a front corner down hard, and a car that bounces twice has dampers that are done β exchange units are $150β300 a side. Budget the front end as a system: kingpins, bushes, dampers, bearings and track-rod ends together are a $1,200β2,200 shop bill, which is why documented front-end work is worth a premium. The steering is a rack and pinion β quick, light and precise when right. Wear shows as play at the wheel (rack bushes or track-rod ends, all cheap), as stiffness from a rack run dry, and as poor self-centring, which usually prices alignment, bushes and kingpins rather than a rack.
At the rear, semi-elliptic springs sag: a Midget sitting tail-down with springs flat or inverted has springs that are finished, and a re-sprung car sits level. The 1500 was raised on taller springs from the factory, so it sits high by design β judge it against another 1500. Whatever the spring type, its mountings are the rust section's hanger boxes, where suspension and shell condition meet.
Brakes are front disc and rear drum from October 1962; the 948's all-drum system is merely adequate even when perfectly maintained. There is no servo on A-series cars, so the pedal is firm by design β judge by whether the car stops straight and the pedal is hard and high. The recommissioning list on a stood car is seized calipers, perished hoses, a tired master cylinder and rear wheel cylinders weeping into the drums: a full hydraulic refresh runs $600β1,200, and a weak handbrake is usually cables and rear shoes. Inspect brake pipes along their whole length on a northern car β a pipe failing on a single-circuit early car leaves you with the handbrake and the scenery.
Interior, hood and trim: the diary of the car's life
The cockpit's condition is a reliable diary of the car's life, written differently for each variant: painted steel dashboard on early cars, a more finished cockpit on the Mk II, the padded US safety dashboard from 1968, and the full late dashboard with emissions-era warning lamps on 1500s. Cracks in a padded dash are cosmetic; missing instruments and bodged wiring behind any dash are evidence about the car's maintainers.
Seats are vinyl over foam and webbing on later cars, simpler padding on early ones. The driver's cushion collapses first, and once you can feel the frame the job is covers and foams together β a retrim kit for both seats is $400β800 in parts, fitted for roughly double. Sit in the driver's seat, not the passenger's; the passenger seat lies about the pair.
The hood β the convertible top, in American terms β prices a viewing, and it is a different item on each mark. Mk I cars have the packaway hood: a dismantling frame, a cover stowed in the boot, and Perspex sidescreens instead of windows β charming, draughty, slow in rain, and a specialist item if missing. The Mk II's hood works with its wind-up windows and is practical. The Mk III's attached folding hood is the best of the range, up or down in under a minute. On any car, erect the hood fully: fabric tears at the folds and header rail, the rear window yellows and cracks, and a hood that does not latch evenly is telling you the frame or windscreen frame has moved. A new hood fitted runs $500β900.
Brightwork and trim are the slow bleed. Chrome bumpers pit, and re-chroming a pair is $600β1,200; grille surrounds, waistline trims, lamp rims and handles all pit, and early-car trim is genuinely scarce. The 1500's rubber bumpers sag, crack and fade. Rubber seals perish on every variant and are the root cause of half the rust in this guide: a full set is a few hundred dollars and a weekend, and fitting it is the cheapest rust prevention there is. None of this is structural, and sellers price shiny trim as if it were condition. It is not β weight the shell and the mechanics.
Electrics: Lucas, earths, and the two charging systems
A Midget's electrics are Lucas, minimal and honest. The variant divide is the charging system. Early cars are positive-earth with a dynamo; negative earth arrived through the Mk II years, alternators followed through the Mk III, and many dynamo cars have since been converted. Establish which system a car runs before judging its charging: a dynamo car's warning light glows at idle by design, while the same glow on an alternator car is a diode or belt problem. On a converted car, check the polarity is marked at the battery and that any period radio or electronic ignition matches it β a negative-earth accessory on a positive-earth car is destroyed by the fitting.
The failures that matter are age failures. Earth straps and body earth points corrode, and because the circuits earth through the shell, one bad earth produces dim lamps, a wandering fuel gauge and indicators flashing at odd speeds β tedious to trace, pennies to fix, and the first thing to check before letting anyone sell you a component. Fuse provision protects very little of the loom, so bodged accessory wiring is common and a genuine fire risk: look behind the dashboard for twisted, taped joins, and treat a tidy, original loom as the sign of a maintained car.
The components that cost money are few. The SU electric fuel pump on later A-series cars sticks after standing β a tap revives it once, a replacement is $120β200, and a car needing the tap every morning needs the pump. Starters and dynamos are exchange items at ordinary prices. On US 1500s, add the emissions-era electrics β converter warnings, seat-belt interlock wiring β most of it partially removed by previous owners; what matters is that ignition and charging circuits are original and sound. A car where everything electrical works has almost always been used and maintained rather than stored, and that is the best single predictor of everything else.

How to inspect one
Allow an hour, bring a torch, a cloth-wrapped magnet and a screwdriver for prodding (with the seller's permission), and work in this order β identity first, structure second, engine checks third, because everything after the shell is priced off the shell.

- Paperwork, plates and prefixes. Match the title to the chassis number, then decode what you are looking at: GAN1 is the 948, GAN2 the Mk I 1098, GAN3 the Mk II, GAN4 and GAN5 the Mk III 1275, GAN6 the 1500. Read the engine prefix next β 9CG, 10CG, 10CC, the 12CC family, or a Triumph number β and treat any disagreement as an engine swap to be priced as such. Invoices for thrust washers on a 1500, a bottom-end rebuild on a 10CG, or sills on any car change the valuation outright.
- Sills first. Hands along both sills with hard pressure, fingers underneath for flaking, then the jacking-point test from the rust section: take the car's weight on each sill socket in turn. Creaking or flexing ends the viewing as a driver purchase β the car is now a project, priced as one, or a walk-away.
- Spring hangers and rear bulkhead. Under the rear of any Mk II or later car, prod the front spring-hanger boxes and the bulkhead behind the seats; lift the trim inside and check the bulkhead's lower corners. On a quarter-elliptic Mk I, prod the spring mountings high on the bulkhead instead. Rot here is structural, exactly as with the sills, and it hides better.
- Floors, boot and tank. Lift every carpet and read the floor edges where the pans meet the sills. Then the boot: spare wheel out, floor prodded, the top of the fuel tank inspected for rust, and the boot lid seal checked for the leak that filled it.
- Cold start and smoke. Insist the engine is cold. Any variant should start readily and settle. Blue smoke that clears is valve-stem seals; smoke that stays under load is bores or rings; a timing-chain rattle that does not fade on an A-series is a worn chain. On a 10CG, listen hardest at a hot idle for the bottom-end rumble that prices a crank rebuild.
- The 1500 thrust-washer check. On any GAN6 car, before the drive and without exception: engine off, lever the front pulley gently fore and aft, or watch it while a helper works the clutch. Movement you can barely feel is correct. Movement you can see, or a clunk, is a worn or dropped thrust washer β the sump-off fix if the crank survives, a rebuild if it does not. No other check on any Midget moves the price this much.
- Oil pressure, oil and breathers. Hot, at speed, the gauge should read strong on either engine family. Emulsion with coolant loss is a head gasket. On an A-series, check the breather is clear before reading a rear bellhousing drip as a seal failure β a blocked breather manufactures that leak on a sound engine. Wiggle every SU throttle spindle: play you can feel is the wandering idle's cause, on HS2s and HS4s alike.
- Kingpins and front end. Jack each front wheel and rock it top-to-bottom. Play that vanishes with an assistant's foot on the brake pedal is wheel bearings; play that remains is kingpin and bush wear, priced from the suspension section. Push each front corner down: two bounces means dead lever-arm dampers. Ask when the grease nipples were last served β this morning does not count.
- The test drive, gearbox by gearbox. Fifteen minutes minimum. In an A-series car the ribcase should engage first only at a standstill β no synchromesh, correct behaviour β and take second without a crunch; in a 1500 the all-synchromesh single-rail should take every gear cleanly, and a vague lever is linkage bushes until proven otherwise. A crunch into second on either box is a rebuild priced into the offer. The clutch should bite without judder, remembering that changing it is an engine-out job on every variant.
- Brakes, heat and stance. Brake hard from speed: straight stop, hard high pedal, no judder β and remember an A-series car has no servo, so effort is not a fault. Let it idle hot and watch the temperature gauge; a car that creeps upward at idle has the silted radiator or tired pump from the engines section. Stand back and read the stance against the variant: level for a chrome-bumper car, tail-down for tired rear springs, high by design for a 1500, and low at one front corner for a spring or kingpin story.
- Hood and weather gear, by mark. Erect the hood fully and latch it. On a Mk III the attached hood should go up in under a minute and latch evenly; on a Mk II, check the folding frame and wind-up windows together; on a Mk I, confirm the packaway hood and both sidescreens are actually in the boot. No working weather gear means a fair-weather car, priced accordingly.
- Electrics and interior last. Establish the charging system first β dynamo or alternator, positive or negative earth β then work everything: lamps, wipers, blower, horn, gauges, and on a US 1500 whatever warning systems remain. Sit in the driver's seat and feel for the frame through the cushion. A sound, original interior and working electrics mark a used-and-maintained car, the hardest things to fake.
Values
Read the market figures that follow this guide β the listings summary and the recorded-sales block, refreshed at every build β with the Midget's variant hierarchy in mind, because on this model the variant sets the ceiling before condition sets the price. The hierarchy is stable. Round-wheel-arch 1275s sit at the top of the mainstream market, combining the best engine, chrome bumpers at the original height and a two-year-only body pressing. Square-arch chrome-bumper 1275s follow, trading the same mechanical package without the arch premium. The Mk II 1098 comes next, valued for its balance and its strong engine rather than its pace. The 1500s anchor the range: the newest, the most numerous and the most discounted, not because they are bad cars but because the rubber bumpers, the raised stance and the single-carburettor American tune are what the market sees first.
Within the 1500s, specification moves money: a European twin-carburettor conversion has earned back a real part of the discount, and documented thrust-washer work earns a premium of its own, because it removes the one finding that can turn a purchase into a rebuild. On early cars the same logic runs through originality β matching prefixes, correct carburettors, sidescreens present β because the market pays for verifiable things and discounts claimed ones.
The second lesson is the condition spread, and no classic's spread is wider relative to its size. The same model year can be a parts car, a driver and a show car, and the distance between those three is almost entirely the shell: welding is priced by the hour and does not care that the car is small, so the gap between a project and a driver is proportionally larger here than on an MGB or a Mercedes. That is why the sill test and, on a 1500, the pulley test move money in a way no photograph does. A large share of American Midgets change hands through marketplace listings and word of mouth rather than auctions β our own pool is drawn entirely from marketplace sellers β so recorded-sales evidence is thinner than for auction-friendly classics. Buy the condition, verify the identity from the plates, let the hierarchy set the ceiling rather than the price, and remember: the cheap car is rarely the inexpensive one.
Parts and ownership
The Midget is one of the best-supported classics in the world: a quarter of a million cars, most of them in America, and a specialist trade β Moss Motors above all in the US β that still manufactures for the car rather than merely warehousing for it. Complete new bodyshells are available from British Motor Heritage, which tells you both how good the support is and what a rotten shell really costs to answer. Support varies by variant, following the production numbers: the 1275 and 1500 owner is served best, the Mk II owner well, and the Mk I owner well mechanically and thinly on trim.
Easy, for every variant: service items, brake hydraulics and friction parts, suspension bushes, kingpin kits, springs, lever-arm dampers on exchange, carburettor service parts and exchange units for HS2 and HS4 alike, clutch hydraulics, exhausts, hoods, seals and glass rubbers. Order today, fit this weekend, at prices that make owners of almost any other classic envious.
Variant-specific and dearer: ribcase gearbox internals in good order are finite and priced accordingly, and the single-rail box's internals come from the Triumph supply chain, so shop them as Triumph parts. The 10CG 1098's crankshaft is the early car's known scarcity β a sound replacement is a hunt. Mk I trim, sidescreen parts and quarter-elliptic spring hardware are the scarcest fittings on the car. Good original chrome is a re-plating budget rather than a parts order. The 1500's thrust washers are the cheapest part in this guide β the money is in the labour to reach them and in the damage when nobody did β and a pinned-washer rebuild, done once and documented, is the best money a 1500 owner ever spends. A quality repaint exceeds the value of most Midgets: buy paint someone else has already paid for.
Running costs. A sorted Midget is a genuinely inexpensive classic to run: fuel economy in the thirties, simple servicing any owner can learn, and insurance in line with its value. The budget line that catches new owners is the first year β catching up deferred maintenance on a running car runs $1,000β2,500, and recommissioning a car that has sat for years, with its fuel system cleaned end to end and every hydraulic component renewed, runs $2,500β5,000 at a shop. The variant adds one line each: a 1500 wants its endfloat checked at every service, an A-series car wants its breathers kept clear, and every car wants its seals renewed before they feed the rust map. Buy a car in regular use over a sleeping one: on a Midget, use is maintenance.
Which one to buy
- The all-rounder: Mk III 1275, round wheel arch (1972β74). The best engine, the best looks, chrome bumpers and the strongest market to sell into. The default choice if the budget reaches β after you have verified the arches are factory round, both sides.
- The value buy: Mk III 1275, square arch (1966β71). The same engine, gearbox and shell without the arch premium. A sorted square-arch car is the smartest money in the range.
- The purist's car: Mk II 1098 (1964β66). Wind-up windows and the strong 2-inch-main 10CC engine in the lightest civilised shell. Slower than a 1275, sweeter than almost anything, and the small-engine car whose bottom end you do not have to worry about.
- The entry point: Midget 1500 (1975β79). The cheapest, newest and most plentiful β and, on the evidence of our pool, the car you will actually find. Buy it only after it passes the thrust-washer check and the sill test, and prefer a European-specification conversion or documented washer work.
- The connoisseur's car: Mk I (1961β64). Rarest and most elemental, sidescreens and all. Choose the 1098 for its brakes and pace with your eyes open about the 10CG crank, or the 948 for originality's sake β and buy the most original car you can find, because originality is the whole value of the mark.
And the rule that overrides all of the above: buy the least rusty shell you can find, with the variant whose signature check it passes β endfloat on a 1500, bottom end on a 10CG, arches on a car priced as a round-arch. Engines, gearboxes, kingpins and carburettors are all fixable at prices you can plan for. A rotten shell costs more to put right than the finished Midget will be worth.
See the 19 midget cars currently listed.
