Mercedes-Benz 240D buyer's guide
Mercedes-Benz 240D -- the model's own buyer's guide: variants, values and what to check.
Years listed: 1974-1983 ยท Series: W115
Overview and history
The Mercedes-Benz 240D is the slowest sensible car you will ever love. That is not an insult โ it is the whole proposition. Under the bonnet sits a 2.4-litre four-cylinder diesel, the OM616, making between 62 and 72 horsepower depending on year and market, pushing a solid, heavy sedan of about a tonne and a half. Acceleration is measured with a calendar. And yet the 240D became one of the most successful Mercedes-Benz models of all time, the default taxi of half the world, and the car that taught two generations of buyers what the word durable actually means. If you are standing in front of one today, you are not buying performance. You are buying the most honest engineering Mercedes ever sold at this price, from the last era when a diesel car had no electronics, no turbocharger, and nothing on it that a competent mechanic cannot understand with the bonnet up and a torch in hand.
The badge covers two generations, and telling them apart is the first skill a buyer needs. The first 240D is a W115, the four-cylinder diesel Stroke Eight, introduced in Europe in August 1973 and sold in North America from the 1974 model year through 1976. The second, and the car most people picture, is the W123 240D, built from February 1976 to November 1985 in Europe and sold in the United States from 1977 through 1983, after which Mercedes-Benz USA dropped the four-cylinder diesel and left the field to the five-cylinder 300D. In our current Classic Listings pool the split is the one you would expect: of the fourteen 240Ds we track, ten are W123s and four are W115s, with model years running from 1974 to 1983 โ every one a US-market car, which is the market this guide is written for.
What made the 240D matter was a commercial-grade diesel in a proper Mercedes sedan, and the market said so in numbers: the 240D sedan was the best-selling single W123 model of all, 454,780 built, ahead of every petrol version โ the 1970s voting with its own money for economy and longevity over speed.
The most famous 240D of all makes the point better than any sales figure. Gregorios Sachinidis, a taxi driver in Thessaloniki, Greece, bought a 1976 W115 240D showing about 220,000 kilometres and ran it as a taxi, around the clock with relief drivers, until July 2004 โ by which point it had covered 4.6 million kilometres, roughly 2.9 million miles, the highest mileage Mercedes-Benz has ever recorded on one of its cars; it is now in the Mercedes-Benz Museum. Be honest about what that story proves, because sellers will quote it at you: the car did it on a rotation of three engines and eleven overhauls. The lesson is not that a 240D engine never wears out. It is that the car around the engine was built to be worth overhauling, again and again. Engines can be rebuilt. A car that was built cheaply cannot be rebuilt into a car that was built well.
Today the 240D is too slow to be a sports sedan, too ordinary to be a blue-chip collectible, and too tough to have disappeared. In our pool, nine of the fourteen cars are automatics and five are manuals, and yellow and white lead the colours, with beige, grey, brown, blue and green behind them. The cars you will go and see divide into cherished survivors maintained like aircraft, and tired old diesels run on neglect because the engine tolerated it. Everything else โ the body, the vacuum system, the interior, the suspension rubber โ keeps the score. This guide is about reading that score before you pay for it.


The models
Every 240D is a diesel, every 240D is a four-cylinder, and nearly every one you will meet in the United States is a four-door sedan. The variations that matter are the generation, the model year โ because the engine was uprated part-way through W123 production โ and the gearbox.
| Model | Years | Engine | Output | Built | Character |
|---|---|---|---|---|---|
| 240D sedan, W115 | 1973โ1976 | 2.4 four, OM616.916, 2,404 cc | 65 hp | 126,148 | The original; upright Stroke Eight charm, simplest trim |
| 240D long, W115 | 1973โ1976 | 2.4 four, OM616.916 | 65 hp | 3,655 | Long-wheelbase taxi and hotel car; rare, buy on condition |
| 240D sedan, W123 | 1976โ1985 | 2.4 four, OM616.912 | 65 hp, then 72 hp from August 1978 | 454,780 | The core car; the best-selling W123 of all |
| 240D sedan, US market, W123 | 1977โ1983 | 2.4 four, OM616.912, US emissions tune | 62 hp, then 67 hp from 1981 model year | Included in the sedan total above | The car you will actually buy in America |
| 240D long-wheelbase, W123 | 1977โ1985 | 2.4 four, OM616.912 | 65 hp, then 72 hp | 3,841 | Eight-seat taxi and limousine work; almost never seen in the US |
| 240TD estate, W123 | 1978โ1986 | 2.4 four, OM616.912 | 65 hp, then 72 hp | 38,903 | The wagon; slow, vast and now genuinely sought after |
(Outputs are period DIN figures for European cars, except the US-market row, which uses the US net ratings. European 240D production ran later than US imports: Mercedes-Benz USA listed the car only through the 1983 model year.)
The W115 cars, 1973 to 1976. The Stroke Eight 240D arrived as the flagship diesel of a facelifted range: ribbed tail lights that shed dirt, a wider grille, and the new 2.4 engine above the 2.2-litre 220D. The chassis number begins 115.117 for the standard sedan. These are charming cars โ slimmer, more upright, with a lighter, more delicate cabin than the W123, thinner seats, simpler instruments and a pull-out stop control rather than the later key-off vacuum shutoff routine you will meet on a W123. They are also the older, rustier, harder-to-trim cars today, and in the US they sold in smaller numbers than the W123 that followed. A good W115 240D is a lovely thing to own slowly. A bad one is a restoration project wearing a running engine as camouflage, and W115-specific trim, interior pieces and some body panels are noticeably harder to source than the equivalent W123 parts.
The W123 cars, 1976 to 1985. This is the main event. The W123 240D sedan, chassis 123.123, launched in February 1976 with the same 65 hp engine in updated OM616.912 form and was uprated in August 1978 โ a revised precombustion chamber and a camshaft with more valve lift, capacity trimmed fractionally to 2,399 cc โ to 72 hp in European tune. US-market cars followed their own ratings path: 62 hp for the 1977 model year, rising to 67 hp for 1981, the difference being emissions tuning rather than a different engine in any sense that matters. A late US car is a little less slow than an early one, and none of them is anything but slow. Buy the condition, not the seven horsepower.
The gearbox split is the real choice. The 240D is the only W123 diesel sedan in the US range that offered a manual โ the 300D was automatic-only in America โ and the manual transforms the car. The automatic is much more common: nine of our fourteen listed cars are automatics. The gearboxes section below prices both.
The cars that are not sedans. The 240TD estate is a genuine 240D variant, built in Bremen with self-levelling rear suspension; America never got it officially, so any example you meet there is a private import and should be checked as one. The long-wheelbase cars were taxi and airport hardware, worked to death almost by definition; a survivor is a curiosity, not a shortcut to value. And one trap to bury here: the W115 240D 3.0 is not a 240D in the sense of this guide at all โ it is the five-cylinder OM617 car, sold in America badged as the 300D. Count the injector pipes on the pump: four is a 240D, five means walk the price back to the 300D guide and start again.


Engines and gearboxes
The OM616: one engine, two tunes, no surprises
There is only one engine in this guide, and that is the 240Ds great strength as a classic purchase. The OM616 is an overhead-cam, single-cam, two-valves-per-cylinder four-cylinder diesel of 2,404 cc in its original form โ bore 91 mm, stroke 92.4 mm, compression ratio around 21 to 21.5 to 1 โ with a cast-iron block and head, five main bearings, a duplex timing chain, and indirect injection: fuel is injected into a precombustion chamber in the head rather than directly into the cylinder, which is why these engines run more softly and rev more willingly than the direct-injection truck diesels of their day, and also why they depend absolutely on their glow plugs to start. In the W115 the engine is designated OM616.916. In the W123 it is OM616.912, and from August 1978 the revised version โ new prechamber design, more camshaft lift, capacity fractionally down to 2,399 cc โ lifts European output from 65 hp at 4,200 rpm to 72 hp at 4,400 rpm, with torque unchanged at 137 Nm, 101 lb-ft, at 2,400 rpm. US cars, as noted in the models section, are rated at 62 hp and then 67 hp in the same years. All of those numbers describe the same driving experience: the engine makes what little power it has low down, pulls honestly from 1,500 rpm, and is done by 4,000. Drive it on torque, change up early in a manual car, and do not expect the rev counter to rescue you from anything.
Understand what understressed means in practice, because it is the reason half the cars in our listings still run. The OM616 produces about 27 horsepower per litre, with bearing sizes, piston crowns and a crankshaft specified for commercial work; the same basic engine powered Mercedes vans and the G-Wagen and was licence-built in India for decades. There is no turbocharger, no intercooler, no electronic control unit, and no exhaust aftertreatment beyond the simple trap oxidiser and exhaust-gas recirculation fitted to some later US-market cars โ California cars in particular โ which are worth identifying because the parts are specific and the system does the engine no favours. A healthy OM616 starts after one glow cycle with a brief clatter and a puff of grey smoke and settles to a steady, busy idle โ these engines are never quiet. Oil pressure should be pegged at the top of the gauge, 3 bar, everywhere except a hot idle, where around 1 to 1.5 bar is normal. Low pressure at cruise rpm means worn bearings or starvation, and neither is a service item.
The service rhythm is part of the specification, and a car that has had it is worth visibly more. Oil and filter every 5,000 miles at most โ many owners run 3,000 to 4,000 โ because the engine soots its oil heavily. Valve clearances are set mechanically on a cold engine โ intake 0.10 mm, exhaust 0.30 mm in the usual specification, check your cars data โ and they close up as the valves seat into the head over tens of thousands of miles. That explains the most common false diagnosis on a tired 240D: an engine that has lost compression, starts badly and feels flat is very often one whose exhaust clearances have closed to nothing, holding the valves fractionally open. A valve adjustment is an hours work, costs $150โ350 at a shop, and has resurrected more condemned OM616s than any rebuild. Before you price an engine as worn out, ask when the valves were last done. If nobody knows, they are due.
The fuel system: Bosch inline pump, injectors and glow plugs
Fuel arrives through a strainer in the tank, a small clear primary filter and a secondary filter, lifted by a mechanical pump on the side of the injection pump. The pump itself is a Bosch inline unit โ the PES-series M-pump, mechanically governed, with a pneumatic governor on most versions. Four plungers, one per cylinder, meter the fuel to Bosch pintle injectors that open at around 115 to 120 bar for new nozzles and spray into the prechambers, where glow plugs make the whole thing possible on a cold morning.
Three systems here decide whether a 240D is a pleasure or a penance, and each has a test.
The glow plug system. Early cars use series-wired loop-style plugs: one plug failing takes the whole string down, and starting becomes a smoky, churning ordeal. Later W123s use parallel pencil plugs under a relay with a proper timer โ the dash light stays on roughly four to five seconds in mild weather, six to eight in cool weather, and nine to twelve around freezing, and the plugs keep glowing after the light goes out. The pencil-plug conversion kit, $150โ300 in parts, is the single best money you can spend on an early car, and a car that has already had it done has had an owner who understood the assignment. Test on inspection: from stone cold, one full glow cycle should start the engine within a few seconds of cranking. Long cranking, or starting on two cylinders in a cloud of white smoke, is glow plugs, closed-up valve clearances, low compression, or air in the fuel โ in roughly that order of cost.
The injectors. Pintle nozzles wear and lose their spray pattern over 100,000 to 150,000 miles: a nailing knock under load from one cylinder, black smoke on acceleration, a lumpy idle. The braided return lines between injectors perish and weep diesel over the top of the engine โ the hose costs $20โ40 a metre and fitting it is a driveway job, so a car wet with fuel on top is careless rather than doomed, but price the carelessness. Rebuilding with new nozzles runs roughly $75โ150 per injector; budget $400โ800 for a set of four fitted, with the pump timing checked afterwards.
The injection pump itself rarely fails outright, but two behaviours matter. On engines where the pump carries its own oil supply rather than being fed from the engines circuit, that oil has to be checked and changed, and neglected pump oil is a slow death for the component you can least afford to replace casually. And the governors diaphragm and the pumps shutoff device are vacuum-operated, which means half the faults that present as fuel faults on a 240D are actually vacuum faults โ the subject of the next section, and the reason a $30 hand vacuum pump is the highest-value tool in this guide. A full pump rebuild, when genuinely needed, runs roughly $800โ1,800.
One more fuel-system truth: a car that has sat for years will have a tank strainer clogged with algae and sludge โ it starts, runs, and dies under load as the strainer blinds over, then restarts after a rest. The cure is dropping and cleaning the tank and strainer and changing both filters, a $300โ700 job at a shop, mostly labour.
Gearboxes: the four-speed manual and the four-speed automatic
The manual is a four-speed all-synchromesh box in the 716 family, with a cable- or hydraulically-operated clutch depending on year โ later W123s use a hydraulic clutch whose master and slave cylinders are cheap, perishable, and capable of making a good gearbox feel broken. The box itself is strong; synchromesh on second gear is the wear point, and a car that crunches into second on a fast change but shifts cleanly when you pause a beat is showing normal middle age, not imminent failure. Clutch life is long, because the engine has not enough torque to abuse it, and a replacement is a $700โ1,200 job fitted โ do the rear main seal while the box is out. Judge a manual car on whether it stays in gear under load and on overrun, and whether reverse engages from rest without a graunch.
The automatic is Mercedes own four-speed, the 722 family โ 722.1 in earlier cars, 722.3 in later W123s โ with a torque converter and vacuum-modulated shift quality. It starts in first on the 240D, because with this engine the car needs every gear it has. Shifts should be firm, prompt and consistent: a soft, sliding shift is wear or low vacuum to the modulator, not character. The vacuum point matters doubly, because the same system that runs the door locks also tells the automatic how hard to shift โ a car with flaring shifts and a dead door lock is very often a car with one vacuum leak explaining both, and the fix is rubber hose, not a rebuild. A genuine rebuild, when the friction material is used up after 250,000 miles of honest work, runs $2,500โ4,500 at a specialist, which can exceed the value of a tired car โ so an automatic that shifts badly with no vacuum explanation is a walk-away at anything but project money. Fluid and filter every 30,000 miles keeps these boxes alive; brown, burnt fluid on the dipstick is a service history in one sniff.
Which gearbox, honestly? The manual car is quicker in the only sense that matters โ in-gear flexibility โ more economical, and worth a premium to buyers who want the full slow-car ritual done properly. The automatic is the easier car in traffic and the easier car to sell. Buy the best example of either rather than a poor example of your preference: a sorted automatic beats a worn manual, every time.


Problem areas
The 240D inverts the usual classic-car logic. On most classics the engine is the risk and the body is the asset; on a 240D the engine is the asset โ the toughest component in the car โ and everything around it is where the money goes: the shell, the vacuum system, the rubber, the interior, and the accumulated neglect of a car that kept running while its owner stopped spending. Work through the problems in the order below, because that is the order in which they should decide your offer. A 240D with a scruffy engine bay and a sound shell is a good car waiting for a service. One with a detailed engine bay and soft jacking points is a parts car wearing make-up.
Rust: the map
Rust is the existential threat to every W115 and W123, and the 240D is more exposed than its petrol sisters, because diesel cars were bought to be used in all weathers, kept longer, and washed less. Protection was paint, cavity wax and thick underseal, all now forty to fifty years old. The good news is that both shells rust in predictable places, in a predictable order, and a methodical half hour with a torch will tell you more than a sellers description ever will.
Jacking points and sills. Start here, always, because this is structural and it is the most common serious failure. The W123 sill is a box section with a reinforced jacking point at each end, hidden behind the sill cover and the plastic jacking-point plugs; water and road salt get in, the section rots from inside, and the first external sign โ bubbling at the bottom edge of the sill or around the jacking point โ means the inside is already worse. Prod with a screwdriver, with permission, around each jacking point and along the sill seam. A sound point takes the cars own jack without creaking or movement; a rotten one is a welding bill, and sill and jacking-point repair done properly โ cut out, new metal, cavity wax, paint โ runs roughly $800โ2,000 per side depending on how far the rot has travelled into the floor edge and the wheelarch. The W115 rots in the same places with slimmer sections and less margin. Four good jacking points do not make a car, but one bad one unmakes the price.
Battery tray and the bulkhead beneath it. Decades of acid vapour eat the tray, then the metal beneath it โ on the W123, the bulkhead above the passengers footwell, where water that gets through runs straight into the cabin. A tray is a cheap panel, $50โ150, but tray rust that has reached the bulkhead is fabrication work, and it announces itself as wet front carpets the seller will blame on a door seal. Lift the battery out on any serious viewing; it is the cheapest structural information you will ever buy.
Floors, and the water that reaches them. The floor pans rot mainly where water sits โ and water sits because the windscreen and rear window seals perish, sunroof drains block where a sunroof is fitted, and the heater intake plenum fills with leaves until its drains clog and it overflows into the car. Lift every carpet. Surface scale under the sound-deadening pads is treatable; holed floors are a $600โ1,500 per side repair fitted, and floor rust never travels alone โ it means the car has been wet inside for years, seat frames, wiring and all.
The rear of the car: wheelarches, spare-wheel well and the panel behind the bumper. Rear arches bubble from the inside out where the skins meet and trap mud; press along the arch lip and feel for the crunch of filler under paint. The spare-wheel well collects every drop that passes the boot and rear light seals, and it is the view sellers photographs avoid โ lift the spare out, because a well can be perforated under a tidy-looking wheel. W123 rear bumpers rust from inside their mounting channel, and the valance goes with them. Three moderate areas add up to one large bill faster than buyers expect.
Front wings and the front suspension mounts. Wing tops and rear edges rot where mud packs behind the wheel, and โ the serious one โ the front spring perches and suspension mounting points on the inner wings must be sound, because they carry the front axle. Perforation around a spring perch is a structural repair, and it is the point at which a cheap W123 stops being cheap in a way no discount fully fixes. Get the car on a lift if it passes everything else: subframe mounts, trailing-arm mountings and the differential mounting all live underneath, and underside photographs are the ones missing from almost every listing you will ever read.
The vacuum system: the 240Ds second engine
A diesel has no throttle butterfly and therefore almost no intake vacuum of its own, so Mercedes fitted an engine-driven vacuum pump โ diaphragm in early versions, piston in later ones โ and ran half the car off it. On a W123 240D, vacuum operates the central locking, the engine shutoff actuator, the climate-control flaps, the automatic transmissions modulator, and the reservoir that stores vacuum so the locks work with the engine off. Every joint is a rubber connector, and after forty years every one of them is a small leak waiting for an audience.
The symptoms are famous. The engine does not stop when you turn the key off โ the shutoff actuator is not getting vacuum, and you stop it with the manual stop lever on the valve cover, fitted for exactly this emergency. One door locks and the others do not, or the locks work with the engine running and not after it stands. The climate controls ignore you. The automatic shifts harshly. The brake pedal goes hard after repeated stops, because the servo drinks from the same pump. Each symptom alone gets misdiagnosed as a failed component; together they are one system, leaking.
Diagnosis is genuinely simple. A hand vacuum pump with a gauge โ $25โ40 from any tool shop โ applied circuit by circuit tells you which branch leaks: isolate the locking circuit at the yellow lines in the engine bay, the shutoff at the pump actuator, the climate circuit at its feed, and test each in turn. Rubber connectors cost pennies; a door actuator diaphragm is $30โ80; a complete renewal of every connector and suspect line is $150โ400 in parts and a weekends patience, and it transforms the car. The expensive failure is the vacuum pump itself โ a worn piston pump, or a failed diaphragm that can dump engine oil into the vacuum lines. A rebuilt or replacement pump runs $250โ600 in parts, and any car whose vacuum is weak at idle with all circuits isolated needs the pump priced into the deal. Weak brakes plus weak everything else equals pump until proven otherwise.
Engine wear, starting and the smoke dictionary
The OM616 wears slowly and announces its wear honestly, mostly through the exhaust and the oil filler cap. Learn the smoke dictionary, because on a diesel the exhaust is a diagnostic instrument. White smoke on a cold start that clears within a minute is unburned fuel from a cold chamber โ glow plugs first, then valve clearances, then compression. White smoke that never clears, with a sweet smell, is coolant, and that is a head gasket conversation. Blue smoke is oil: a puff on start-up after standing is valve stem seals, a known and manageable job; blue smoke under load, worsening as the engine works, is rings and bores, and that is a rebuild. Black smoke is over-fuelling or under-airing: a clogged air filter, worn injectors, or a pump delivering too much โ check the filter first because it is free, and be suspicious of any car whose pump has been turned up by a previous owner chasing performance that this engine does not have to give. A turned-up pump makes smoke, heat and a short story out of a long engine.
Blow-by is the compression test you can do at the kerb. With the engine hot and idling, rest the oil filler cap loosely on the neck. On a healthy engine it sits with a gentle tremble. If it dances and tries to leave, crankcase pressure from worn rings is pushing past โ some blow-by is normal on a high-mileage diesel, but a cap that will not stay on is an engine with its best miles behind it, priced as a future rebuild: $3,500โ6,500 for a proper OM616 rebuild with machining. Set that against the reputation fairly: 300,000 miles on an original, serviced engine is unremarkable, and 400,000 is documented regularly. The engines that die early die of overheating, closed-up valve clearances ignored until a valve burns, or a neglected oil level โ all owner faults, and all leave evidence in the history file.
The timing chain stretches and its tensioner and guides wear; a rattle for a second at start-up is the tensioner taking up, a rattle that stays is a chain asking for attention, and a chain job runs $600โ1,200 fitted. A jumped chain on an interference diesel ends valves, so do not ignore a noisy one. Overheating matters just as much: the cooling system is simple, and an OM616 that runs hot has a clogged radiator, a failed thermostat, a slipping belt or a dying water pump โ all cheap, right up until the day it warps the head, which is not. Budget $400โ900 for a full cooling-system refresh and consider it the best insurance in this guide.
Engine mounts collapse with age โ the OM616 shakes at idle by design, and on dead mounts it shakes the whole car. Mounts are $40โ90 each in parts and an hour or two to fit, and new ones transform a car out of all proportion to cost. Oil leaks are universal and mostly trivial โ valve cover, filter housing seals, front crank seal, sump gasket; judge leaks by rate, not presence. Oil in the coolant, or coolant in the oil, is a different conversation entirely and it is a head-off one.
Suspension, steering and brakes
Both generations ride on double wishbones at the front with coil springs and a semi-trailing-arm independent rear axle. There are no exotic components; the bad news is that every joint and bush is now old, and a 240D that wanders and knocks is simply a car wearing its original rubber at fifty.
Front ball joints and tie-rod ends wear and knock over sharp bumps; guide rod mounts โ the big bushes that locate the W123 front axle fore and aft โ perish and give a clunk under braking and a vague feel at speed that owners misdiagnose as steering box wear. A full front-end refresh runs $800โ1,800 fitted and is the single biggest drivability improvement available. The recirculating-ball steering box adjusts for free play at the centre; a little is normal, a quarter-turn of slack is wear, and a rebuilt box is $400โ800 exchanged. At the rear, trailing-arm bushes and subframe mounts soften until the car steers gently from the rear in crosswinds; check the differential mount and the rubber guibo discs in the propshaft, which crack with age and announce themselves as a vibration and a thump. A cracked guibo is a $60โ120 part and a safety item, not a quirk.
Springs sag, especially at the rear of hard-worked cars; a 240D should sit level and even. Broken rear springs, usually the bottom coil inside the arm where you cannot see it, are common enough that you should feel for them. Shock absorbers are conventional and cheap, $60โ140 a corner, and a car bouncing twice after a push on each corner needs them.
Brakes are discs at the front on all of these cars and at the rear on W123s, with a vacuum servo and a simple hydraulic system. The failure mode is sitting: seized calipers, perished flexible hoses, a master cylinder bypassing internally so the pedal sinks slowly at lights. A full hydraulic refresh โ rebuilt calipers, hoses, master cylinder, fluid โ runs $700โ1,600 fitted and is non-negotiable money on any car that has stood. The handbrake is a small drum inside the rear disc and needs its own adjustment; one that barely holds is its own small job, not a verdict on the service brakes.
Interior, climate and electrics
The cabins are famously durable and specifically expensive in the same places. MB-Tex vinyl is close to immortal; the padding beneath it is not โ horsehair pads in earlier cars crumble to greenish dust under the seats, and foam in later W123 seats collapses until you are sitting in the spring frame. Re-padding a front seat runs $250โ500; the spring box breaks at the front corners on drivers seats and squeaks forever until it is welded. Judge every interior from the drivers seat, because that is the seat that prices the car. Leather was rare on a 240D and is usually tired when found. The dashboard cracks across the top on sun-baked W123s, and a proper cure is a dashboard-out job at $800โ2,000 all-in with a good used dash โ which is why a crack-free original is worth money.
Wood on W123s โ zebrano on most 240Ds โ cracks its lacquer on the glovebox lid and centre console first; mismatched pieces mean one has been replaced. The heater and climate system is vacuum-operated, and its blower motor lives behind the dashboard: a dead blower is a long job, $600โ1,500 fitted, on a motor that costs a fraction of that. Test the blower on every speed, on every viewing, whatever the weather. Manual climate cars are simpler and better at this age than the automatic climate control on later US cars, whose servo faults are a known cottage industry โ a late US car with working automatic climate has been maintained; one without has a bill waiting, $500โ1,200 to put right. Air conditioning, where fitted, will almost certainly be converted, tired or both; recommissioning a dead system runs $800โ1,800, so price working cold air as the asset it is.
Electrics are simple and fail at the connections: earth points corrode, and the W123 fuse box uses ceramic torpedo fuses whose contacts oxidise until circuits drop out intermittently โ spin every fuse in its holder on inspection and half the gremlins in the car will confess. The odometer gear crumbles, which is why so many 240Ds show mileages that stopped being true years ago: treat every reading as a claim, not a fact, and buy the wear on the pedals, the seat and the steering wheel instead. Glow plug relays fail, alternator brushes wear to nothing at high miles and cost almost nothing to renew, and diesel starters eventually announce themselves with a slow, reluctant crank that owners misdiagnose as a battery.


How to inspect one
Allow at least an hour, and insist on one condition before you set off: the engine must be stone cold when you arrive, because a diesel warmed up for you is a diesel whose cold start โ the single most informative event in a 240D inspection โ has been hidden. Bring a torch, a hand vacuum pump with a gauge, a screwdriver for prodding with the sellers permission, and a magnet wrapped in cloth. If the car passes you, pay for a lift inspection before money changes hands; on a car whose worst faults live underneath, it is the best money in the whole purchase.
- Start with the paperwork and the identity. Match the title to the chassis number โ on a W123 it is stamped on the bulkhead and shown on the door-pillar plate of US cars, beginning 123.123 for a 240D sedan; on a W115 look for 115.117. Count the injector pipes at the pump: four pipes is a 240D, five pipes is a 300D in disguise, whatever the badge says. Ask for the history file โ on these cars a folder of oil-change and valve-adjustment receipts is worth more than any single mechanical feature.
- The cold start. Turn the key to the glow position and watch the light: roughly four to five seconds in mild weather, longer in the cold. One glow cycle, then crank. A healthy car fires within a few seconds, clatters briefly, puffs grey and settles. Long cranking, starting on two cylinders, or white smoke that takes minutes to clear points to glow plugs, closed-up valve clearances or low compression โ in that order of cost. A car that was warm when you arrived has not been tested at all; come back another morning.
- The filler-cap test. With the engine warmed through later in the inspection, rest the oil filler cap loosely on the neck at idle. A tremble is normal; a cap that dances and tries to blow off is blow-by from worn rings, and it reprices the engine. Note the oil pressure story for the drive: pegged at speed, a bar or so at a hot idle.
- The shutoff test, and the vacuum snapshot. Turn the engine off with the key. It should stop promptly, with one shake. An engine that runs on, or stops only on the manual stop lever, has a vacuum leak or a tired pump โ and that one observation predicts the door locks, the climate controls and, on an automatic, the shift quality. Test the central locking twice, once running and once five minutes after switching off: locks that work running and fail standing are telling you the reservoir or a check valve leaks.
- Underneath: jacking points and sills first. Torch and screwdriver along both sills, prod every jacking point, and if the seller allows, take the cars weight briefly on its own jack at each point โ a sound point lifts silently, a rotten one creaks and flexes, and a seller who refuses the test has answered it. Then floors, spring perches and subframe mounts. Perforation at jacking points, perches or bulkhead is structural; this step decides whether the inspection continues at all.
- The boot and the floors inside. Lift the spare wheel and look into the well corners for water, scale and holes. Inside, lift all four carpets: water tracks from the windscreen base, the heater plenum and the rear screen explain themselves in staining long before they explain themselves in holes. Wet carpets in a dry-stored car mean leaking seals and a wet history.
- Body, gaps and the magnet. Run the wrapped magnet over sills, arch lips, lower doors and wing bottoms; filler announces itself where the magnet will not hold. Feel along every door bottom for bubbling, look down each flank for ripples, and count the rust bubbles honestly โ each one is a repair, and together they are a respray budget.
- Smoke and the test drive. Fifteen minutes minimum, including a hill. Watch the mirror on hard acceleration: black smoke is fuelling or a clogged filter, blue is oil, white that persists is coolant until proven innocent. A manual car should hold each gear under load and on overrun, with second-gear synchromesh tested on one brisk change. An automatic should shift firmly and consistently, with no flare and no thump into reverse โ and remember the vacuum link before you condemn the box.
- Steering, suspension and brakes. The steering should centre cleanly and track straight hands-off on a flat road; wander plus a clunk under braking is guide rod mounts before it is a steering box. Brake hard from speed twice: straight, no judder, no pull, and a pedal that stays firm at the next lights โ a sinking pedal is a master cylinder confessing. Push down on each corner and release: one bounce and settle is a live damper.
- Heat and electrics, all of them. Let the car idle hot and watch the temperature gauge settle and stay. Run the blower on every speed โ a dead blower is a dashboard-out bill โ and try every window, the washers, wipers, horn, lights and indicators. Spin the torpedo fuses in their holders on a W123 and retry anything that was dead; oxidised fuse contacts are the cheapest fix in the car and the most misdiagnosed.
- Interior, from the drivers seat. Sit in the drivers seat first and feel for the spring frame through a collapsed pad; look under the seats for the greenish dust of dead horsehair. Check the dash top for cracks and the wood for lifted lacquer, and read the odometer with open suspicion โ believe the pedal rubbers, the wheel rim and the seat bolster over the numbers.
- Stance, leaks and the final look. Stand back: a sagging rear, broken spring or tired mounts all show from ten paces. After the drive, look underneath for fresh drips โ fuel at the injector returns, oil at the filter housing, coolant at the pump โ and at the ground where the car stood when you arrived, which is the leak history the seller could not wipe up in time. Then decide by the rule from the problem areas: buy the shell and the history, and let the engine look after itself.
Values
The 240D market is a condition market wearing a model badge, and the listings block beneath this guide โ the current cars, the recorded sales, the spread between them โ is the only set of numbers you should trust, because it is recomputed from the market itself rather than remembered from last year. What this section teaches is how to read those numbers when you get there.
Start with the spread, because on a 240D the spread is the story. At any given moment the pool contains cars that are, mechanically speaking, the same vehicle, separated in asking price by a multiple, not a percentage. The bottom of the market is not made of a cheaper model. It is made of rust, of vacuum systems that do not work, of interiors baked and split, of engines that start badly and cars that have stood. The top is made of the opposite list, plus two things money cannot retrofit: an unwelded shell and a documented life. Do not ask which of two far-apart cars is overpriced until you have run the rust map and the cold start on both; on this model, the expensive car is very often the cheap one, once the first year has presented its invoices.
Within that spread, some premiums are real. The manual gearbox earns one โ not because manuals are faster in any way a stopwatch would respect, but because the manual car is the one keen drivers want, it was the minority choice when new in America, and it cannot be converted cheaply or authentically later. The late W123 earns a smaller premium over the early car, but it is a gentle slope, not a step: a superb early car beats a tired late one at any price. The 240TD estate is the one variant where scarcity genuinely speaks, since America never received it new; treat any example as an individual negotiation about an imported car, not as a sedan with a longer roof.
Asking and achieved prices part company predictably here: sellers of ordinary cars price by hope and by what they have spent โ steady small amounts that add up to a number the market will not return โ while sellers of genuinely good cars often price modestly because the cars look humble. Auction results and recorded sales, which the block below tracks, are the corrective. Use asking prices to find cars; use achieved prices to value them.
The project-versus-driver gap is the other number that matters, and it is wider than the purchase prices suggest. A project car is cheap to buy and then charges you for a tank clean, a brake hydraulic refresh, a vacuum renewal, tyres, mounts and whatever the lift inspection found โ a recommissioning that routinely totals a substantial fraction of what a sorted driver would have cost, before any welding. A driver with a history file costs more on the day and then costs you oil, filters and valve adjustments. The gap between the two asking prices is smaller than the gap between the two first-year totals, and the driver is usually the better arithmetic. Negotiation, finally, is honest on these cars: faults are demonstrable and tests are cheap, so price what you can demonstrate, with the repair estimates from the sections above.
Parts and ownership
The 240D is one of the best-supported working classics you can own: Mercedes built them in the hundreds of thousands, the same running gear served in vans and the G-Wagen, and the cars are still working for a living in much of the world. The Mercedes-Benz Classic Center covers a wide range of factory parts and the specialist trade is deep. You will not be stopped by parts. You will occasionally be slowed by trim, and once or twice be quoted a number for a dashboard-out job that makes you sit down.
Easy and cheap: service items across the board โ filters, glow plugs, belts, hoses, thermostats, water pumps, brake discs, pads, calipers and hoses, clutch components, mounts, propshaft couplings, shock absorbers, ball joints, tie rods, bushes, exhaust systems, injector return hose by the metre, and the rubber connectors the vacuum system eats. Order today, fit this weekend, at prices that would not embarrass a modern hatchback. A full service in consumables is $150โ300; a set of four glow plugs is $40โ80.
Harder and dearer: the Bosch injection pump when it genuinely needs a rebuild, $800โ1,800 through a diesel shop; a rebuilt vacuum pump, $250โ600 in parts; the heater blower motor, cheap as a part and $600โ1,500 fitted because of where it lives; automatic climate servos on late US cars; crack-free W123 dashboards; W115-specific trim and interior pieces, where the earlier cars smaller production tells; and structural panels fitted and painted, where the panel is the cheap part and the hours are the bill. A quality repaint starts in the several-thousand range, which is the economic reason the values section tells you to buy the shell.
Running costs are the reason the car exists. Fuel consumption in the high twenties to low thirties miles per gallon is realistic for a manual car, a little worse for an automatic, and the engine asks for oil and filters every 5,000 miles or less, valve clearances on the same rhythm, and fluids on time rather than on failure. The budget line that catches new owners is the first year: catching up a neglected 240D โ cooling system, brake hydraulics, vacuum renewal, mounts, filters, a tank clean if it has stood โ honestly runs $1,500โ4,000 in the first twelve months. After that, a sorted 240D is among the cheapest classics in the world to keep.
Living with it deserves plain words. A 240D is slow in modern traffic in a way that changes how you drive: you plan overtakes in a different county, hold momentum like a religion, and arrive unstressed because the car has removed hurry from the available options. Owners consistently report that this is the charm, not the compromise. In winter, give it its glow cycle and keep the battery strong โ a big, healthy battery is not optional on a compression-ignition car in January. Do that, and the car that started this morning will start every morning, which is the entire point of a 240D.
Which one to buy
- The all-rounder: a late US W123 sedan, 1981 to 1983, automatic or manual on condition. The uprated US tune, the deepest parts support of any car in this guide, and the easiest resale when your plans change. If you want one 240D to use, this is it.
- The drivers car: a W123 with the four-speed manual. The gearbox the engine always wanted, worth a premium and worth waiting for โ momentum kept is speed gained. Buy the best manual you can find rather than the first one.
- The value buy: a sound early W123 automatic, 1977 to 1980. The same shell, the same engine in its earlier tune, and a market that discounts it for a handful of horsepower neither car can spare anyway. The discount buys the cooling-system refresh and the vacuum renewal.
- The character buy: a W115 sedan, 1974 to 1976. Slimmer, simpler, more delicate, and the generation of the 4.6-million-kilometre taxi. Buy it only with a sound shell, because W115 trim and panels will test your patience in a way W123 parts never will.
- The collector curiosity: a 240TD estate or a long-wheelbase car. Genuinely scarce in America and priced as individual negotiations. Buy either only as an inspected import with its paperwork in order, and never as your first 240D.
And the rule that overrides all of the above: buy the least rusty 240D you can find, with the thickest history file, in whichever generation and gearbox that car happens to be. The engine will outlast your plans for it either way; vacuum leaks, glow plugs, mounts and filters are all cheap and fixable at prices you can plan for. A rotten shell and an undocumented life are the two things no amount of money turns back into original โ and the two things sellers photographs are least likely to show you.
See the 14 240D cars currently listed.
