Chevrolet Blazer buyer's guide
Chevrolet Blazer -- the model's own buyer's guide: variants, values and what to check.
Years listed: 1966-2001 ยท Series: C/K Trucks
Overview and history
The Chevrolet Blazer is really two different vehicles wearing one name, and the first job of any buyer is to know which one is standing in front of them. The original is the K5 Blazer of 1969โ91: a full-size, body-on-frame 4x4 built from Chevrolet's C/K pickup line, with a short wheelbase, a removable top and small-block V8 power. The second is the S-10 Blazer of 1983โ2005: a compact SUV spun off the S-10 pickup, smaller in every dimension, V6-powered, and sold in far greater numbers as everyday family transport. Both are Blazers, both are Chevrolets, both are now bought as classics โ but they share almost no parts, no driving character and no market logic. This guide covers both, and keeps them separate throughout, because nearly every mistake in this market starts with judging one by the other's standards.
The K5 arrived in 1969, three years after the Ford Bronco had shown there was money in a short, open, off-road wagon. Chevrolet's answer was characteristically pragmatic: rather than design a new vehicle, it shortened the K10 pickup frame to a 104-inch wheelbase, kept the pickup's engines, gearboxes, axles and front sheetmetal, and put a two-door wagon body on top with a fully removable fiberglass top. With the top off, a K5 is a convertible; with a rear seat, it carries four or five; drop the tailgate and it is a pickup with a very short bed. GMC sold the same truck as the Jimmy. The formula worked immediately, and the Blazer outsold the Bronco comfortably through the 1970s.
The first generation ran 1969โ72, on the rounded "Action Line" pickup styling. The second generation โ the "square-body" โ ran a remarkable 1973โ91, with a facelift in 1981 and another, milder one for 1989. Two changes inside that long run matter more than any styling tweak. For 1976 the full convertible top gave way to a fixed steel half-cab over the front seats with a removable hardtop over the rear only, a safety-driven change that ended the true open car. And in 1987 the carburettors gave way to throttle-body fuel injection, which transformed cold starting and drivability. The full-size line continued on the newer GMT400 platform as the 1992โ94 Blazer before being renamed Tahoe for 1995 โ those trucks are close cousins of the last K5s mechanically and are worth a buyer's attention, but the K5 name, and the removable top, end in 1991.
The S-10 Blazer followed the same recipe one size down. Launched for 1983 alongside the S-10 pickup, it took the compact truck's frame, engines and running gear and added a two-door wagon body on a 100.5-inch wheelbase. A four-door on a longer wheelbase joined it in 1991, and that is when the S-10 Blazer became a mainstream family vehicle rather than a lifestyle toy. A second generation arrived for 1995 with rounded styling and, in the US, effectively one engine โ the 4.3-litre V6 โ and ran to 2005. GMC's version was the Jimmy; the 1999โ2001 TrailBlazer began life as an upmarket trim of this truck before becoming a separate, larger model.
Why buy either now? The K5's case is simple: it is the last of the big, simple, removable-top American 4x4s, mechanically a pickup โ which means mechanically understood by every shop in America. The S-10's case is different: it is the affordable end of the classic SUV market, a genuinely usable daily-driver classic with real 4x4 hardware in most examples, and the 4.3 V6 versions are quicker and tougher than their prices suggest. In our own listings we currently track 98 Blazers, and the year spread tells the story: 1972 is the single most common year, the square-body years are well represented, and the S-10's strongest year in the pool is 1994. The early K5 is the collector car; the square-body is the volume classic; the S-10 is the entry point.
One warning before anything else: a large share of K5s, especially early ones, have been modified โ lifted, re-engined, re-axled, repainted in non-original colours, or all four. Modification is part of this model's culture in a way it is not for a European classic, and it is not automatically a defect. But it changes what you are buying and what it is worth, and the inspection section treats originality as something to establish, not assume.


The models
The K5 Blazer, 1969โ91
Every K5 is a two-door wagon on a shortened pickup frame. The badge logic is simple once you know it: K means four-wheel drive in Chevrolet's truck coding, and the Blazer was overwhelmingly a 4x4 โ but a two-wheel-drive version (technically a C-series truck wearing Blazer badges) was offered in both generations and is now rare and, in the early years, genuinely sought after as a street truck. Trim ran from the plain Custom Deluxe through Scottsdale and Cheyenne to Silverado at the top, with the CST (Custom Sport Truck) package the desirable early option. Engines and years are in the table; the character notes are the part to read twice.
| Model | Years | Engine | Output | Built | Character |
|---|---|---|---|---|---|
| K5 Blazer (first generation) | 1969โ1972 | 250 six / 307 / 350 V8 | 155โ255 hp | โ | The original full convertible; the collector car |
| K5 Blazer (square-body, early) | 1973โ1980 | 250 six / 305 / 350 / 400 V8 | 100โ175 hp (net) | โ | Full top to 1975, half-cab from 1976; smog-era power |
| K5 Blazer (square-body, late) | 1981โ1991 | 305 / 350 V8, 6.2 diesel | 130โ210 hp | โ | Lighter nose, overdrive automatic, TBI injection from 1987 |
| K5 Blazer 2WD | 1969โ1982 | Six / small-block V8 | As above | Low volume | The street Blazer; rare early, dropped after 1982 |
| Full-size Blazer (GMT400) | 1992โ1994 | 5.7 V8 (TBI), 6.5 diesel (1994) | 180โ210 hp | โ | The K5's successor; renamed Tahoe for 1995 |
| S-10 Blazer (first generation) | 1983โ1994 | 2.5 four / 2.8 V6 / 4.3 V6 | 92โ200 hp | โ | Compact original; 4-door from 1991, 4.3 is the one to have |
| S-10 Blazer (second generation) | 1995โ2005 | 4.3 V6 (2.2 four in some 2WD) | 118โ200 hp | โ | Rounded family SUV; the affordable daily classic |
(GM published Blazer production inside its truck totals in a way that does not give clean, trim-by-trim build figures a buyer can rely on, so this guide does not invent them. Outputs are period figures โ gross ratings before 1972, net ratings after โ which is why the same 350 V8 appears to "lose" power across the 1971โ72 boundary. It did not; the ruler changed.)
First generation, 1969โ72. The collector's Blazer. Styling matches the 1967โ72 pickups, the top comes off completely โ unbolt it and the whole roof, sides and rear lift away, leaving a windshield and doors โ and the specification is pure truck: leaf springs, a Dana 44 front axle on 4x4s, and front disc brakes standardised early in the run. The 350 V8 is the engine the market wants; the 250 six is honest but slow in a truck this heavy; the 307 sits between and fools nobody. Two-wheel-drive first-generation cars are the sleeper of the range: built in small numbers, and increasingly bought as cruisers.
Square-body, 1973โ80. Bigger-feeling, squarer, and built on the 106.5-inch wheelbase it kept to the end. Cars to 1975 are still full convertibles โ the last of the true open K5s, and worth a premium over a 1976 for exactly that reason. From 1976 you get the steel half-cab: safer, quieter, far less leaky, and the rear top section still removes for open-air load space. This is the smog era, so outputs sagged โ a mid-seventies 350 makes roughly what a 307 made in 1970 โ and specification varied wildly by state, with California cars carrying the most emissions hardware. The 400 small-block (1970s cars) is the torque pick of this span; the 305 that arrived at the end of the decade is the economy engine and feels it.
Square-body, 1981โ91. The 1981 facelift lightened the front end and cleaned up the styling; more importantly, the decade brought the 700R4 overdrive automatic, the 6.2-litre diesel (1982 on), and for 1987 throttle-body injection on the petrol V8s, which is the single biggest drivability step in the K5's life. The 1989-on cars got a revised grille and composite headlights and are the most civilised square-bodies: fuel-injected, overdrive-equipped, air-conditioned trucks you can drive across a state without thinking about it. If you want a K5 to use rather than to show, start here. The diesel is a specialist taste โ covered in the engine section โ and the 305 cars are the budget entry, fine if priced as such.
GMT400 Blazer, 1992โ94. Not a K5, and priced as if the market knows it: independent front suspension instead of a live axle, a full steel roof, and a much more car-like cabin. Mechanically it is the late K5's running gear matured โ 5.7 TBI V8, four-speed automatic โ and as a usable classic truck it is arguably the best of the full-size line. Buyers cross-shop it constantly; just do not pay a removable-top premium for a truck whose top does not remove.
The S-10 Blazer, 1983โ2005
The S-10 Blazer mirrors the K5 story one size down: a two-door wagon on the compact pickup frame, with the four-door (1991 on, 110.5-inch wheelbase) becoming the volume seller. Trim ran from base through Tahoe and Tahoe LT โ confusingly, Tahoe here is a trim level, years before it became a model name โ to the later LS and LT badges.
The model decision that matters on an S-10 is not the trim; it is the engine and the door count. The early cars came with a 2.5-litre four and a 2.8 V6 that were adequate in a pickup and marginal in a loaded 4x4 wagon. The 4.3 V6, offered from 1988 and dominant from the early 1990s, transforms the truck โ it is effectively three-quarters of a small-block V8, with the torque to match โ and a 4.3 car is the default recommendation in this range. Two-doors are the classic shape and the ones enthusiasts want; four-doors are the practical buy and usually cheaper for the same mechanical condition. The 1995 second generation is rounder, safer and better finished, but also more appliance-like, and the market prices it that way: these are cheap, useful trucks, bought on condition alone.

Engines and gearboxes
The K5 sixes and small-block V8s
The K5's engine bay holds the most familiar engines in America, and that familiarity is the model's greatest ownership asset. The story in one line: an inline six for the base cars, and Chevrolet's small-block V8 โ 307, 305, 350 and 400 cubic inches โ for everything else, carburetted until 1986 and throttle-body injected from 1987.
The 250 six (and its taller-deck 292 brother, offered early) is a simple, torquey inline six that will run badly for years before it runs not at all. In a 4,500 lb truck it is slow โ motorway merging is a planned event โ and the market prices six-cylinder cars accordingly. Its virtues are real, though: nothing in the bay is expensive, fuel consumption is the best of the K5 range, and an unmodified six-cylinder car has often lived a gentler life than a V8. Check for oil weeping from the side covers, a cracked exhaust manifold (a tick that fades as it warms), and wear in the single-barrel carburettor's throttle shaft, which gives an idle no adjustment will stabilise.
The small-block V8 is the default K5 engine and one of the most durable designs ever built โ with known, specific weaknesses a buyer can test for. The 350 is the pick of the family: the largest supply of parts, the best balance of power and economy, and in a K5, enough torque to make gearing rather than power the limiting factor off-road. The 307 (early cars) is a smaller-bore engine that sellers occasionally describe hopefully as a 350 โ the engines look identical outside, so check the casting and suffix codes on the pad at the front of the right-hand block deck, and the casting number at the back of the block, rather than trusting the air-cleaner decal, which is a sticker, not evidence. The 305 (1980s cars) is the economy small-block: fine in service, unloved by the market, and the first thing restomod builders remove โ a 305 car with a later 350 swapped in is common and legitimate if disclosed and done properly. The 400 (1970s cars) has siamesed bores, runs hotter by design, and cracks heads and blocks in ways the other small-blocks do not if it has ever been seriously overheated; it is a torque engine for towing, and any 400 car needs its cooling history interrogated.
Across all the small-blocks, the failure list is consistent. Valve stem seals harden with age and give the classic puff of blue smoke on start-up after sitting, clearing within seconds โ in our photo-check sample of Blazers, smoke was notably not a recorded problem, which matches the engine's reputation: these motors wear slowly. A puff on start-up is a seal job, top-end work in the region of $600โ1,200 at a shop, not a rebuild. Smoke under load, by contrast, is rings and bores, and that is an engine-out conversation. Rear main seals weep โ two-piece seals on early engines more than the one-piece seal from 1986 โ and a dry underside on a high-mile small-block is rarer than a damp one; judge the rate, not the presence. The flat-tappet camshafts in every pre-1987 engine were designed for oils carrying more zinc (ZDDP) than most modern oils provide; premature cam and lifter wear on a freshly rebuilt engine run on the wrong oil is a genuine modern failure mode, and a knowledgeable seller of a carburetted car should be able to tell you what oil it runs and why. Listen for a single rhythmic tick at idle that rises with revs: one worn lifter is a nuisance, a lobe going flat shows as a cylinder that will not respond to tuning.
Carburettors. Most K5s run a Rochester Quadrajet four-barrel (two-barrel Rochesters on some base cars), and the Quadrajet gets blamed for faults in everything around it. The known real faults are a warped air horn from decades of uneven bolt tightening (an idle and off-idle stumble that no jet change cures), worn throttle-shaft bores leaking air, and a perished choke pull-off diaphragm โ which gives the classic cold-start stall the owner blames on "the carb". A proper rebuild by a specialist who will bush the throttle shafts runs roughly $400โ800; the amateur test is whether the car starts from cold on the choke, idles steadily hot, and pulls without a flat spot. Throttle-body injection (1987 on) replaces all of that with two injectors in a unit that behaves like a blessing: cold starts on the key, no choke ritual, and faults that reduce to a tired fuel pump (a weak pump shows first as a lean surge at cruise), perished vacuum hoses, and a leaking throttle-body base gasket. A TBI car that runs badly is usually a sensor or a vacuum leak, not a rebuild.
The 6.2 diesel
From 1982 the K5 offered Detroit Diesel's 6.2-litre naturally aspirated V8, also sold in vast numbers to the US military in the CUCV version of this same truck. It makes little power โ around 130โ150 hp โ but its torque arrives low, its economy beats any petrol K5, and it has a devoted following. It is also the engine in this guide most likely to bankrupt a buyer who treats it like a small-block. The known faults: head gaskets and, on overheated engines, cracked heads and blocks (the cooling margin is thin, and the fan and radiator must be perfect); a Stanadyne rotary injection pump that wears and gives hot-start failure โ a hot engine that refuses to restart will often start after the pump is cooled with water, which is diagnostic, not a cure, and a pump rebuild is specialist work around $800โ1,500; glow-plug faults that present as white smoke and endless cranking on cold mornings; and harmonic balancer rubber that perishes and, ignored, can break the crankshaft โ inspect the balancer on any diesel car and budget its replacement as routine. Buy a diesel only with evidence of cooling-system and balancer care, and only if you actually want one: the market is thin in both directions.
The S-10 engines
The S-10's engine history is a story of arriving at the right answer in 1988. Before that, the base 2.5-litre "Iron Duke" four (tough, rough and slow) and the 2.8-litre 60-degree V6 (smooth enough, underpowered in a 4x4, and prone to oil leaks from every gasket it owns) powered cars the market now buys mainly on price and condition. The 2.8's known habits are intake and rear-main leaks and a timing chain that stretches.
The 4.3 V6 is the engine that matters. Derived from the 350 small-block with two cylinders removed โ same bore, same stroke, same architecture โ it came in throttle-body form (about 160 hp), then central-port injection (CPI, the "W-code" engine, up to 200 hp in the early 1990s), then sequential injection on the 1996-on Vortec. It is torquey, long-lived and cheap to fix, with three signature faults every buyer must know. First, the intake manifold gaskets: the plastic-framed gaskets fail and leak coolant externally, or worse, internally into the oil โ milky residue under the oil filler cap and a coolant level that falls with no puddle is the test, and the job is $700โ1,200 at a shop with the updated gasket design. Second, on CPI cars, the central injector "spider" and its poppet nozzles live inside the intake manifold, fed by a fuel pressure regulator that eventually leaks into the manifold: hard starting, a rich smell, washing-down of one bank, and misfire codes follow, and the cure is a replacement injector assembly (parts $300โ600, and an upgraded multi-port conversion exists and is the fix to prefer). Third, the remote oil-cooler lines on 4x4 cars weep and then leak at their crimps โ a known, cheap part whose failure, ignored, empties the sump; look at the lines on any 4.3 4x4 and budget replacement if they are damp. Add distributor wear (a worn drive gear gives a wandering idle and a squeak from the back of the engine) and you have the 4.3's whole charge sheet โ a short list for an engine this common, which is the point.
The second-generation cars standardised the 4.3 (a 2.2 four powered some two-wheel-drive cars and is best avoided in a Blazer body). By then the engine was the Vortec with sequential injection: the intake-gasket fault carried over, the spider fault did not, and the rest is modern-car ageing โ sensors, EGR valves carboning, and an ignition system that wants its cap, rotor and leads on schedule.
Gearboxes and four-wheel drive
K5 manuals are the three-speed column-shift of the earliest base cars and, far more commonly, the SM465 four-speed: a heavy truck gearbox with a very low "granny" first used for crawling and pulling away under load, effectively a three-speed on the road. It is nearly unbreakable; judge it on bearing noise and on whether it jumps out of gear under load. Automatics dominate: the TH350 three-speed in most 1970s cars, the stronger TH400 in some heavy applications, and from 1982 the 700R4 four-speed with overdrive โ the gearbox that makes a late square-body a motorway car. Early 700R4s failed behind diesels and in towing use; buy one whose box shifts cleanly and has evidence of fluid changes, and know a full rebuild is a known quantity at roughly $1,800โ3,000. Whatever the automatic, the tests are the same: fluid that is red and smells of nothing much (brown and burnt is a rebuild negotiation), shifts firm without being violent, no delay engaging drive or reverse from cold, and no flare between gears.
The transfer case is where K5 identity checks matter. Early cars used the gear-driven NP205 โ heavy, noisy, and effectively indestructible, with a cast-iron case. Most square-bodies use the chain-driven, aluminium-case NP208, lighter and quieter, whose chain stretches with age and abuse and announces itself as a bang or ratcheting under load in four-wheel drive; late cars got the NP241, a stronger development of the same idea. Part-time systems need the front hubs locked (manual hubs on most, automatic locking hubs on many 1980s cars โ and automatic hubs that fail to engage, or fail to release, are a period fault that has sent many owners to manual replacements). Full-time four-wheel drive (NP203 chain-drive) was offered in the mid-1970s and is now usually converted to part-time. Test any system on a loose surface: engage low range, confirm it pulls, listen for chain slap, and check the front propshaft and its double-cardan joint, whose wear gives a vibration sellers blame on tyres.
The S-10 runs lighter versions of the same hardware: five-speed manuals (Borg-Warner T5 early, later NV3500-family boxes) that are pleasant and durable, the 700R4 and then the electronic 4L60E automatic, and New Process transfer cases (NP207, NP231, and the NP233 electronic-shift in later cars). The electronic-shift cases add a failure mode โ an encoder motor or switch that leaves you in two-wheel drive with a flashing light โ that is cheap in parts and maddening in diagnosis. Vacuum-actuated front-axle engagement on many S-10s is the other classic: a perished vacuum actuator under the battery tray means the light says 4x4 and the front axle says otherwise. Test engagement on dirt, not on the seller's word and not on the dashboard lamp.


Problem areas
Everything in this section follows the same order a buyer should think in: the body first, because on a Blazer the body decides whether the truck is a purchase or a project; then the chassis and steering; then the top, the tailgate and the interior, which is where these trucks hide their second tier of costs. The mechanicals come last because, on a Chevrolet truck, they are the most fixable part of the package. Our own photo-checking gives the same ranking: of 38 Blazers we examined in sellers' photo sets, rust was recorded on 11 cars and visible damage on 8 โ body condition, not mechanical failure, is what separates the cars.
Rust: the map
A Blazer rusts like the pickup it is, with two additions of its own: a removable top that lets water in at the top, and a tailgate and rear quarters that trap it at the back. Work through it in this order.
Rocker panels and cab floor. The structural heart of the check. The rockers rot from inside, fed by mud thrown up by the front wheels and held against the inner faces; the cab floor follows, especially under the mats where water from leaking top seals and windshield rubbers collects. Press hard along the full rocker length, lift the carpets and the sill plates, and prod the floor around the cab mounts. On square-bodies add the cab corners and the floor supports โ the boxed sections under the floor that carry the body mounts, which rot invisibly until the body starts to sit crooked on the frame. Repair is well understood (panels are cheap and every truck shop has done it) but it is welding, not cosmetics: a pair of rockers, cut out, welded and painted, runs roughly $800โ1,800, and floors with their supports are a bigger conversation. Fresh underseal or new rocker covers over soft metal is the oldest trick in the truck market; a magnet wrapped in cloth and a screwdriver, used with permission, settle it.
Front wings, wheel arches and inner wings. The square-body's squared arches trap mud at their lips, and bubbling at the arch edge means the inner structure is already involved. Front wing bottoms behind the wheels rot in sympathy with the rockers. On first-generation cars the same applies with the addition of the cowl sides and the lower windshield frame: the early K5's windshield frame is a known rot point precisely because the full top bolts to it and water sits in the joint โ and a rotten windshield frame on a 1969โ75 full-convertible is a serious repair, because that frame is both structure and top mounting. Check it with the top's front rail in mind, and look for filler along the top of the frame where the latches sit.
The rear: quarters, tailgate and rear floor. The Blazer's own territory. Rear quarters bubble over the wheel arches and rot at their lower trailing edges behind the wheels. The tailgate rusts along its bottom edge and around its window channel โ and the tailgate is a complicated panel carrying a roll-down window, so its repair costs more than its size suggests. Lift the rear carpet and check the load floor and the body mounts at the very back; water that enters past the top's rear seal runs down and sits exactly there. On S-10 Blazers the same map shrinks but does not change: rockers, door bottoms, rear quarters over the arches, the bottom of the tailgate/liftgate, and โ on four-doors โ the lower rear door skins. S-10 frames also deserve a specific look at the rear half, where road salt collects around the spring hangers.
Doors, and the small traps. Door bottoms fill with water when their drain slots block: run a fingertip along the bottom edge of each door for bubbling. The battery tray rots under the battery, and on S-10s the tray hides the 4x4 vacuum actuator beneath it, so one inspection covers two faults. The cowl and plenum collect leaves and rot the firewall on trucks that have lived outdoors; a damp passenger footwell after rain is the tell. None of these alone kills a truck; together they tell you how it has lived, and the honest summary is the one from the top of this section โ rust appeared in the photos of nearly a third of the cars we checked, so assume you will find some and price what you find, rather than shopping for the mythical truck with none.
Frame, suspension and steering
The frames themselves are strong, ladder-type, and usually survive โ with one famous exception. On square-body trucks, the frame rail cracks around the steering box mounting: the box is bolted to the outside of the left rail, the rail flexes under steering loads (worse with big tyres and lifts), and cracks radiate from the bolt holes. It is common enough that weld-in repair plates and bolt-on braces are standard catalogue parts. Any square-body inspection that skips this has skipped the model's signature structural fault: get the wheel turned, watch the box while someone rocks the steering, and look for movement of the box against the rail and hairlines around the bolts. Budget a few hundred dollars for a brace-and-repair on a cracked car, and walk away from one where the rail itself is torn.
Steering wear otherwise follows the truck pattern. Worn tie-rod ends, a tired steering box (adjustable, up to a point โ an over-tightened box that binds at centre has been adjusted past its life), and perished rag joints give the classic vague, wandering square-body drive. It is all cheap parts and known labour; a full front-end refresh is a weekend-scale job, not a specialist sentence. The serious version is a truck whose steering faults are blamed on wear but are actually the cracked rail above.
Suspension judgement depends on generation. K5s ride on leaf springs at both ends; the faults are sagged and cracked leaves, perished bushings, and โ above all โ the archaeology of other people's lift kits. A lifted truck is not a bad truck, but a badly lifted one is: check for extended shackles doing the work of springs, blocks on the front axle (a genuine danger point โ front lift blocks are the one modification to treat as an automatic walk-away), steering geometry nobody corrected (a dropped pitman arm should accompany a real lift), and propshaft angles that explain a vibration. On S-10s, the front is independent with torsion bars on 4x4s: sagging bars cranked to compensate, worn ball joints (the uppers are a known wear item), and idler-arm play are the standard list, and all of it is inexpensive.
Brakes are discs at the front (standard on K5s from early in the first generation) and drums at the rear throughout the K5's life; S-10s are the same until the later second-generation cars gained rear discs in some applications. The standing-truck list applies: seized calipers, perished flex hoses, a rusty hard line along the frame rail, and a master cylinder weeping into the booster. A full hydraulic refresh is $800โ1,800 at a shop and should be assumed on any truck that has sat. Judge discs and drums by their surfaces, and remember the parking brake on a drum-brake truck that has lived in the salt belt is usually a cable-and-shoes rebuild, not an adjustment.
The top, the tailgate and water
The removable top is the K5's glory and its main water source. The fiberglass top itself rarely fails structurally, but its seals perish, its mounting bolts seize or strip their captive nuts, and on full-convertible 1969โ75 cars the windshield-frame joint leaks onto the front floor. A top that has been off and on carelessly gets chipped edges and stress cracks around the bolt holes. Replacement seals are available and fitting them is owner-scale work; a cracked or warped top is a hunt for a used one, because nobody reproduces the whole shell cheaply. On 1976-on half-cab cars, check the fixed cab's rear panel and the top's front seal line, and look at the paint witness marks: a top that has not been off in decades shows it, which is honest information, not a fault.
The tailgate window is the K5's signature small mechanism: the rear glass rolls down into the tailgate, electrically on most or by a crank on early and base cars. Regulators wear, cables stretch, motors tire, and the window channels fill with the grit of forty summers. A slow or crooked window is a regulator-and-channel job โ a few hundred dollars in parts and a fiddly afternoon โ but test it on every viewing, because a seller who says "the window just needs a fuse" is describing the day he stopped investigating. S-10s use a liftgate with a separate opening glass on later cars; struts and hinges are the whole story there.
Water management ties the section together: on any Blazer, damp carpets are never "just" damp carpets. Trace them โ top seals, windshield rubber, cowl, or heater core (a sweet smell and a misting windscreen give that one away, and on an S-10 the heater core is a dashboard-out job to be priced accordingly, $800โ1,400 at shop rates; on a K5 it is mercifully more accessible).
Interior, trim and electrics
Truck interiors age by sun and by use, and Blazer interiors have usually had both. Vinyl and cloth seat covers split at the driver's bolster first; the foam and the seat springs follow. Sit in the driver's seat and feel for the frame: re-covering a pair of buckets with new foam is $800โ1,500 professionally, and a good original interior โ especially the early CST and Cheyenne trim โ is worth real money because reproduction trim covers the common colours well and the unusual ones barely. Dash pads crack in the sun on every generation; square-body pads are reproduced, S-10 dashes crack around the defroster vents, and a crack-free dash in a southern truck is a small miracle worth paying for.
Electrics are the trucks' easy chapter. Wiring fails at grounds and connectors, not in the looms: dim lights, a wandering fuel gauge and intermittent accessories are earth-point hunts. The period items are fusible links that corrode, and the tailgate-window and (on later cars) electric-shift 4x4 circuits already covered. Air conditioning, where fitted, is the big-ticket accessory: a complete, working system on a square-body is a selling point precisely because so many have dead compressors and R12-era hardware; a full recommission with conversion runs $1,200โ2,500, so "air blows warm, just needs gas" should be priced as "air does not work". S-10 electrics add modern faults โ blend-door actuators that click and leave the heater stuck, and passlock security faults that give a no-start with a flashing light โ all known, all documented, all fixable at sensible money.

How to inspect one
Allow an hour, bring a torch, a magnet wrapped in cloth, a tyre-pressure gauge and a friend to rock the steering wheel while you watch the steering box. Everything below is ordered so the checks that kill a car come first: identity, body, frame, then the running gear.
- Start with the paperwork and the plates. Match the VIN on the title to the plate (driver's door jamb on most, dash corner visible through the windshield on later cars) and to the frame stamping where accessible. Decode the trim tag under the hood for original colour and trim, and โ on a K5 โ read the SPID label in the glovebox (square-body cars) for the factory option list: engine, axle, transfer case, trim. A "350 car" whose SPID says 305, or whose engine suffix code disagrees with the story, is not necessarily a bad buy, but it is a different buy, at a different price.
- Cold start. Insist the engine is cold. A small-block should fire on the choke (carburetted) or on the key (TBI) and settle; a 4.3 should start without throttle. Watch the exhaust for the first ten seconds: a brief blue puff that clears is valve seals; continuous smoke is not. Listen for a diesel's cold behaviour separately โ long cranking and white smoke on a 6.2 is the glow-plug and compression story told in one start.
- The oil and coolant checks. Pull the dipstick: on a small-block you are reading level and condition; on a 4.3 you are also looking for the milky emulsion of an intake-gasket leak, and under the filler cap too. Check the coolant level on a 4.3 with no visible leak โ a falling level with dry hoses is the gasket again. On a CPI 4.3, smell the oil for petrol: a leaking in-manifold regulator washes fuel into places it should never be.
- Rockers, floors and cab mounts. Torch and screwdriver along both rockers, under the carpets in both footwells, and at the floor supports and body mounts. Perforation in rockers or floor supports is structural money; surface scale is not. On a 1969โ75 full-convertible, give the windshield frame the same treatment โ it is structure, and it is where the top bolts on.
- The steering-box test (square-bodies especially). Have your friend rock the steering wheel through its free play while you watch the steering box from the engine bay and the wheel arch. The box must not move against the frame rail. Movement, or visible hairline cracks around the mounting bolts, is the model's signature frame fault โ a brace-and-repair job if caught as cracks, a walk-away if the rail is torn.
- The rear of the truck. Work the tailgate window up and down twice โ fully. Slow, crooked or noisy is a regulator job to price, not a fuse. Then the tailgate bottom edge, the rear quarters behind the wheels, the load floor under the carpet, and the rear body mounts. Water staining at the back is the top seal's confession.
- The top. On a full-convertible, examine the windshield-frame joint and the top's bolt line; on any K5, check the top's seals, look for stress cracks around the mounting holes, and ask when it was last off โ then look at the paint witness lines and decide whether you believe the answer. A top that has never been off is fine; a top whose seals are dust will leak on your first wet drive home.
- Underneath: running gear. Propshafts (double-cardan joint wear at the front), transfer-case leaks and chain noise history, axle pinion seals, brake hard lines along the frame rail, and the exhaust. On an S-10 4x4, add the 4.3's oil-cooler lines โ damp crimps mean replacement โ and the vacuum actuator under the battery tray, whose tray you are checking for rot at the same time.
- The four-wheel-drive test. On a loose surface โ gravel, dirt, the seller's yard โ engage 4-High and 4-Low. It should engage without a fight, pull from the front, and show no ratcheting bang under load (a stretched NP208 chain) and no flashing-light refusal (an S-10's encoder or vacuum fault). A truck that "hasn't been in four-wheel drive for years" is a truck whose system you are buying untested: price that honestly.
- The test drive. Fifteen minutes, including a highway stretch and some broken pavement. An automatic should engage drive and reverse without delay, shift firmly, and โ in a 700R4 or 4L60 car โ settle into overdrive and lock-up at cruise without hunting. A small-block should pull cleanly through a Quadrajet's secondaries; a flat spot is the carburettor section's checklist, not a mystery. Brake hard from speed: straight, no judder, no pull. Note the steering at centre โ wander is wear or a cracked rail, and you have already tested which.11. Stance and suspension. Stand back and look. Sagged leaves, a torsion-bar S-10 cranked unevenly, a lift with front blocks or geometry nobody corrected โ all visible from twenty feet. Bounce each corner: dead dampers on a truck this size are cheap, but they complete the picture of how it has been maintained.
- Interior and electrics last. Sit in the driver's seat and feel for the frame through the foam. Work everything: windows (especially the tailgate glass, again), blower on all speeds, wipers, washers, lights, gauges, and the air conditioning โ priced as not working unless it demonstrably blows cold for ten minutes. A truck where everything works has been used and maintained, which on a Blazer is the best predictor of everything you cannot see.
Values
The market content beneath this guide โ the live listings summary and the recorded-sales block the build appends โ carries the current numbers, refreshed at every build. This section teaches you how to read them, because the Blazer market punishes buyers who read a single figure and stop thinking.
The first thing to understand is the condition spread, which on a K5 is wider than on almost any car in this programme. The same model year can be a rusted field truck, an honest driver, a restored show car and a six-figure restomod, and all four appear in the same listings feed wearing the same badges. Compare a car against others in its own condition class, or you will conclude that every honest driver is overpriced and every project is a bargain. Neither is true: the project class is where the money goes to die, because a K5's restoration costs โ welding, paint, trim, top seals, a tailgate mechanism โ are the same whether the finished truck is a six or a V8, an early car or a late one.
The second is the originality and modification question, which cuts both ways here. On an early K5, original specification โ matching engine, factory colour, uncut body, its top and its trim intact โ carries a real premium, because so few survive that way. On a square-body, the market is more forgiving and often rewards tasteful, well-executed modification: a quality lift, a properly done engine swap, a professional repaint. What it punishes in both generations is the middle ground โ modified badly, or original but worn โ and undocumented work of any kind. A restomod's value lives in its receipts; a seller who cannot produce them is asking you to price his claims, and you should decline.
The third is the generation ladder. Early full-convertible cars sit at the top, with 1969โ72 first and the 1973โ75 full-tops close behind; the half-cab square-bodies form the broad middle, with fuel-injected 1987-on cars the most valuable of them because they are the most usable; the diesel is a thin, specialist market; and two-wheel-drive cars have split โ early ones rising as street trucks, later ones still the budget route in. The GMT400 cars trade below K5 money because the top does not come off, which makes them the value buy of the full-size line for anyone honest about never removing a top anyway. S-10 values are condition-only: the 4.3 and the two-door carry the interest, and no S-10 should be bought as a financial proposition โ buy it because it is the right truck at the right money.
On asking versus achieved: truck sellers, dealer and private alike, ask with optimism, and auction results for comparable cars routinely settle below the asking prices of similar listings that sit. Use the recorded-sales block, not the asking block, to value a car you are buying; use the asking block to value the competition your own car will face when you sell. And apply the standing rule of this market: the gap between a project and a driver is almost always smaller than the cost of turning the project into the driver. Buy the driver.
Parts and ownership
The Blazer sits at the easy end of classic ownership, because it is a Chevrolet truck, and Chevrolet trucks are the most-supported old vehicles in America. The aftermarket catalogue industry reproduces an astonishing proportion of both trucks, and the mechanical parts interchange with the pickups built in the millions.
Easy: every service item for every engine in this guide; small-block and 4.3 internals, gaskets and ancillaries; brake, steering and suspension wear parts; glass, rubbers and seals; square-body and S-10 body panels including rockers, floors, arches and tailgate skins; seat covers and interior trim in the common colours; transfer-case chains, hubs and propshaft joints. Order today, fit this weekend, at prices that make European-classic owners wince.
Harder and dearer: complete removable tops (used only โ seals and hardware are reproduced, shells are not); first-generation windshield frames; early CST and unusual-colour trim; 6.2 diesel injection pumps and good cylinder heads; CPI injector assemblies for the early-1990s 4.3 (the upgraded conversion kits are the sensible buy); GMT400-specific trim; and crack-free dash pads in the right colours. A quality repaint on a K5 โ a big, square, two-tone truck โ starts in the same territory as a car's, and body preparation is where the money goes: price any truck needing paint as if the paint job costs what it costs, not what the seller hopes.
Running costs. A sorted K5 is a realistic regular-use classic with truck appetites: fuel consumption in the low-to-mid teens for a petrol V8, worse for a lifted one on big tyres, and the diesel the honourable exception. The small-block and the 4.3 ask for 3,000โ5,000-mile oil changes, attention to the flat-tappet oil question on pre-1987 engines, and nothing exotic. The budget line that catches new owners is the same one as everywhere in this programme: the first year of catching up deferred maintenance โ brakes, hoses, belts, fluids, tyres that are older than they look โ honestly runs into the low thousands on a driver-grade truck, and recommissioning one that has sat means the full fuel system, tank to carburettor or injectors, cleaned or renewed against modern ethanol fuel. Buy a truck in regular use over a sleeping one, even at a higher price: on a Blazer, use is maintenance.
Ownership has one more dimension cars do not: these trucks get used. A Blazer you buy will be borrowed for house moves, taken on trails and lent to relatives. Decide your own rules early โ especially about the top on an early car, which rewards careful handling and punishes being forced โ and the truck will hold its condition better for it.
Which one to buy
- The collector car: a 1969โ72 K5, 350 V8. The original full convertible, the strongest market, the best-supported early truck. Verify the engine and the windshield frame ruthlessly, and pay for originality only where you have proved it.
- The value classic: a 1973โ75 square-body. The last full convertibles, priced below the first generation for the same open truck. Condition is the deciding factor, as always.
- The one to use: a 1987โ91 K5. Fuel injection, overdrive automatic, air conditioning that can be made to work properly. The square-body at its most civilised, and the pick for driving distance.
- The torque pick: a 400 V8 car from the 1970s, or a well-kept 6.2 diesel. The 400 for towing and effortlessness, with its cooling history proven; the diesel only for committed diesel people, with balancer and pump evidence in the file.
- The street truck: a two-wheel-drive early Blazer. Rare, rising, and huge fun as a cruiser. Buy the best body you can find; the mechanical conversion temptations can wait.
- The budget full-sizer: a 1992โ94 GMT400 Blazer. The K5's running gear matured, at money the removable-top cars no longer ask.
- The entry point: a 4.3 S-10 Blazer, two-door if you can find it. Three-quarters of a small-block's character in a compact truck at compact money. Intake gaskets and oil lines checked, it is the cheapest seat in the classic-SUV house.
And the rule that overrides all of the above: buy the least rusty truck you can find, in the specification you can live with.Engines, gearboxes, transfer cases and tailgate regulators are all fixable at prices you can plan for. A rotten shell โ rockers, floors, windshield frame โ costs more to put right than the finished truck will be worth, and on a Blazer it is the one thing that can never be made original again.
See the 62 Blazer cars currently listed.
