BMW 3 Series 325i Convertible 2D buyer's guide
BMW 3 Series 325i Convertible 2D -- the model's own buyer's guide: variants, values and what to check.
Years listed: 1986-1995 ยท Series: E30
Overview and history
The BMW 325i is the car that made the 3 Series the default answer to the question of what a driver's car should be. It is not the fastest BMW of its era, not the rarest, and not the most exotic โ it is the sweet spot. A compact rear-wheel-drive sedan, coupe or convertible with a smooth six-cylinder engine, a proper five-speed manual gearbox, and handling that still embarrasses cars built decades later. Buy one well and you get a usable classic that starts every morning, keeps up with modern traffic, and rewards you every time the road bends. Buy one badly and you get a rusty, deferred-maintenance money pit wearing a badge that flatters it.
There are two quite different cars wearing the 325i badge, and this guide covers both, because the market mixes them freely. The first is the E30, built from 1982 to 1994, the boxy, upright 3 Series that turned BMW from a niche European marque into a mainstream American aspiration. The American 325i arrived for the 1987 model year, and the E30 convertible carried on until 1993, long after the sedan and coupe had given way to the new car. The second is the E36, launched for 1992, a rounder, more modern car with a twin-cam engine and a far more sophisticated chassis. Both are called 325i. They share a badge, a 2.5-litre six and a philosophy, and almost nothing else. A buyer who cannot tell them apart at a glance will pay E30 money for an E36, or the other way round, and the inspection in this guide is different for each.
The E30 325i was BMW's answer to a problem of its own making. The earlier American 325e, sold from 1984, used a 2.7-litre "eta" engine tuned for economy: long-stroke, low-revving and miserly with fuel, but with a redline barely above 4,500 rpm and a character closer to a diesel than to a sports sedan. For 1987 BMW gave America the engine Europe already had: the M20B25, a 2.5-litre six with a proper 6,500 rpm redline and real top-end urge. The 325i was the result, and it immediately became the 3 Series to buy โ quick enough to be entertaining, refined enough to commute in, and simple enough that an owner with tools could keep it alive.
The E36 325i that followed for 1992 was a bigger step than the badge suggests. The M50 engine is a twin-cam, 24-valve unit with a timing chain instead of a belt, and the chassis is a generation more refined: multi-link rear suspension in place of semi-trailing arms, better crash structure, and a cabin that feels a decade newer. It is a better car in most objective ways and, to many enthusiasts, a slightly less characterful one. Both generations are now old enough that condition, not specification, decides value โ and both are old enough that rust and neglected belt or cooling maintenance have had thirty-plus years to work.
On Classic Listings we currently track 20 BMW 325i cars for sale in the United States, all listed through Facebook Marketplace, and the split tells you where the market is: 16 of the 20 are E30s, model years 1986 to 1991, and four are E36s from 1993 to 1995. The peak years in our pool are 1987 to 1989 โ five 1988 cars, four 1987s and three 1989s. Fourteen of the twenty are manuals and six are automatics, which is the right way round for a car whose manual gearbox is one of its best features. Grey is the commonest colour with six cars, followed by white with four, and the cars are spread across the country, with Texas and New York leading at three each. There are no sold cars in the pool to cross-check against, so everything about achieved values in this guide is framed as reading the asking market, not as a record of completed sales.
That market is almost entirely private sellers โ every one of the 20 cars comes from a Marketplace seller rather than a dealer โ which shapes how you should buy: no dealer to lean on, no warranty, no reconditioning to assume. The car you see is the car the last owner stopped maintaining, or kept maintaining, and the inspection in this guide is written for exactly that: a private sale, a driveway, and an hour of your time before money changes hands.

The models
Every 325i is a 2.5-litre six, rear-wheel drive except for the one all-wheel-drive E30, and available with a five-speed manual or an automatic. The differences that matter are the generation, the body style, and whether the car is a plain 325i or one of the sport-packaged variants. Work through them in this order, because generation comes first: an E30 and an E36 with the same badge are different cars with different engines, different faults and different values.
| Model | Years (US) | Engine | Output | Character |
|---|---|---|---|---|
| E30 325i sedan and coupe | 1987โ1991 | 2.5 six (M20B25), belt cam | 168 hp | The classic; the core of the market |
| E30 325is coupe | 1987โ1991 | 2.5 six (M20B25) | 168 hp | Sport package: limited-slip, spoilers, sport seats |
| E30 325i convertible | 1987โ1993 | 2.5 six (M20B25) | 168 hp | Open car; built two years after the coupes ended |
| E30 325iX | 1988โ1991 | 2.5 six (M20B25) | 168 hp | All-wheel drive; rare, complex, sought-after |
| E36 325i sedan, coupe and convertible | 1992โ1995 | 2.5 six (M50), chain cam | 189 hp | Twin-cam successor; more refined, more electronics |
(Outputs are US-market figures; European E30 cars were rated at 170 hp DIN, a measurement difference, not a different engine. Variant production totals were never published in a form we trust โ the E30 as a whole ran to well over two million cars โ so any seller quoting a precise build number for an ordinary 325i cannot verify it either.)
The E30 sedan and coupe. The default 325i, and the car most of our pool is made of. Two-door and four-door cars share the same running gear; the sedan is the practical one, the coupe the prettier one, and in today's market the coupe carries a small premium for its looks. Early cars, 1987 and the first 1988s, wear the big aluminium "diving board" bumpers that American regulations imposed; from the 1989 model year the E30 got shorter, body-coloured plastic bumpers, a revised valance and ellipsoidal headlights on many cars, and those later cars โ "plastic bumper" cars in the classifieds โ are the ones buyers pay most for. The facelift is cosmetic, not structural, so never pay a facelift premium for a car whose sills are worse than an early car's.
The 325is. The coupe with the sport package: a limited-slip differential, a deeper front spoiler, a small bootlid spoiler, firmer suspension, sport seats, cross-spoke alloy wheels and a more complete trip computer. There is no more power โ the engine is identical โ but on the road the limited-slip and the seats make it the better car to drive hard, and collectors know it. Because the premium rides on the specification, verify it: the limited-slip is the item that matters, and the test is physical. Jack the rear, turn one wheel, and the other should turn the same way on a limited-slip car and the opposite way on an open differential. Spoilers and badges bolt on in an afternoon; a differential does not get swapped casually. Our pool is listed under the plain 325i name, and any 325is in it is hiding inside that name, which is exactly why the check matters.
The 325i convertible. The open E30, and a surprisingly large part of the surviving population, because convertibles were bought as second cars, garaged more, and scrapped less. The E30 convertible was built until 1993, two years after the coupe and sedan were replaced, which is why the newest E30s you will ever see are convertibles. Early cars have a manual folding top; power tops arrived on later cars and add motors, microswitches and linkage to the inspection. The convertible is heavier and less stiff than the coupe, and on a rough road you will feel the body work โ but it is the cheapest way into open-top E30 ownership.
The 325iX. The all-wheel-drive E30, sold in America from 1988 to 1991 as a sedan and coupe. A viscous-coupled transfer case sends power to all four wheels through a unique front axle, unique front suspension and a higher ride height. It is a genuinely capable winter car, but it is the most complex E30 there is: the transfer case, front differential and front driveshaft components are iX-specific, some are no longer easy to find, and the higher body hides its own rust pattern. Buy an iX because you want an iX, with your eyes open about parts โ never because it was the only 325i left in your budget.
The E36 325i. The successor, sold in America from 1992 to 1995 as a sedan, coupe and convertible, and replaced by the 328i for 1996. It is bigger, quieter, safer and quicker than the E30, with the twin-cam M50 engine and a multi-link rear axle. Four of the twenty cars in our pool are E36s, and they are typically the cheaper end of the 325i market today โ the E30 has crossed into classic status and the E36 is still, in buyers' eyes, an old modern car. That will not last, and a good E36 bought now is bought at the bottom of its curve. Just be clear about what you are buying: the E36 is not a more modern E30. It is a different car that shares a badge, and its faults โ cooling system plastics, VANOS wear, more complicated electrics โ are its own.
The cars that are not 325is, however the badge reads. The most important model in this guide is one that does not appear in the table. The E30 325e and 325es, sold from 1984 to 1987, use the 2.7-litre eta engine, look nearly identical to a 325i, and are worth meaningfully less because the engine is the whole point of the 325i. Badges are cheap, bootlids get swapped, and sellers โ innocently or otherwise โ describe eta cars as 325is constantly. The same goes for the plain 1988 "325", which carries the late "Super eta" engine: a good car, but not a 325i. The identification tests are in the engines section and step 1 of the inspection, and they are the single most valuable five minutes in this guide. A 325i is an engine code, not a bootlid badge.

Engines and gearboxes
The M20B25: the engine the 325i is about
The E30 325i's engine is the M20B25, a 2,494 cc single-overhead-cam six with two valves per cylinder, an iron block and an alloy head, fed by Bosch Motronic electronic fuel injection. It makes 168 hp at 5,800 rpm and 164 lb-ft of torque at 4,300 rpm in US form, revs to a 6,500 rpm redline, and does the one thing no figure captures: it pulls harder and sounds better the higher you rev it. A healthy one starts instantly, idles at a steady murmur, and revs cleanly to the redline without a flat spot. If the car you are testing does not want to rev, it is not "characterful" or "torquey" โ it is ill, or it is not a 325i at all.
The M20's defining maintenance fact, and the single most important sentence in this guide, is this: the camshaft is driven by a toothed rubber belt, and the engine is an interference design. If the belt breaks or sheds its teeth, the pistons meet the valves and the engine needs a cylinder-head rebuild at minimum. Belts age by time as well as mileage, and the disciplined interval is 60,000 miles or four to five years, whichever comes first โ belt, tensioner pulley and water pump together, because the pump sits behind the belt and replacing it later means doing the whole job twice. A complete belt service at an independent specialist runs roughly $700โ1,200 with the pump and tensioner. The inspection question is therefore not "how many miles since the belt?" but "show me the invoice." A seller who cannot date the belt is selling you a car whose first job is a belt service, and the price should say so. Never rev an unknown-belt car hard on the test drive: you are testing the engine, not detonating it.
The rest of the M20's service life is old-fashioned and owner-friendly. Valve clearances are set by eccentric adjusters on the rocker arms โ no shims, no buckets โ and want checking roughly every 15,000 miles; a top end that ticks slightly when cold and quiets when warm is normal. The oil spray bar above the camshaft feeds the rockers, and on neglected engines it blocks, starving the cam lobes โ look at the visible cam lobe through the oil filler for scoring if you suspect neglect. Oil leaks are endemic and mostly cheap: valve cover gasket, oil filter housing seals, front crank and cam seals, and the half-moon plugs at the ends of the head all weep with age. Budget $300โ800 to dry an engine out properly, and treat a bone-dry engine bay with the same suspicion as a soaked one โ dry usually means recently pressure-washed for the sale.
Cooling is the M20's other discipline. The cylinder head is prone to cracking if the engine is seriously overheated, so a temperature gauge that has ever been pinned or a cooling system full of stop-leak is a serious mark against a car. The viscous fan clutch fails with age and the car overheats in traffic while staying cool on the highway โ a healthy clutch resists being spun by hand when hot and roars audibly pulling away from a hot idle. Thermostats stick, radiators silt, and every rubber hose on a thirty-five-year-old car is a consumable whether it looks tired or not.
On the fuel and spark side, Motronic is reliable and its faults are mechanical in disguise. The idle control valve gums up and gives a hunting or high idle โ remove it and clean it before condemning anything electronic. The rubber intake boot between the air-flow meter and the throttle body cracks with age and heat, admits unmetered air, and causes a lean, lumpy idle that owners chase through sensors for months; squeeze the boot and look into the folds. The air-flow meter's flap and track wear, injectors dribble, the fuel pressure regulator's diaphragm splits and sends fuel up its vacuum hose, and the main and fuel pump relays โ cheap, in the relay box beside the airbox โ fail with age and strand cars completely. Carry spares of both relays in the glovebox of any M20 car you own; they cost little and they are the difference between a five-minute fix and a tow truck.

The eta trap: M20B27 and the cars that are not 325is
The engine that causes more misdescribed sales than any other in this market is the M20B27, the 2,692 cc "eta" unit fitted to the E30 325e and 325es from 1984 to 1987. BMW designed it for economy after the fuel crises: a long stroke, a low compression ratio, small ports, a redline around 4,500 rpm, and 121 hp with its torque delivered low down. It is a durable, pleasant, unhurried engine. It is also, in a car badged 325i, a fraud โ sometimes the seller's, sometimes a previous owner's, sometimes just a swapped bootlid from a breaker's yard. The 1988 model-year plain 325 uses a revised "Super eta" with 127 hp and is caught by the same tests.
Learn the tells, because none of them requires opening anything. An eta car's tachometer is redlined at about 4,800 rpm; a 325i's tachometer runs to a redline just past 6,500 rpm โ look at the dial before you start the engine, because a seller cannot talk his way around a printed redline. On the road the test is even simpler: a real 325i pulls eagerly past 5,000 rpm and is still gaining; an eta is finished by 4,500 and feels it. Under the bonnet, the definitive check is the engine number stamped on the machined pad on the block: the code identifies the engine as a 2.5 or a 2.7, and the casting and the emissions label under the bonnet will agree with it. Check at least two of the three โ tachometer, road behaviour, engine code โ before you pay 325i money for any E30. The reverse trap also exists: a genuine 325i engine swapped into an eta shell is worth less than an original car, not more, because originality is what the premium buys.
The E36 engine: M50 and M50TU
The E36 325i uses the M50B25, a 2,494 cc twin-cam, 24-valve six making 189 hp. From the 1993 model year the M50TU version added single VANOS variable valve timing on the intake cam, which broadened the torque curve and is the version in most of the E36 cars you will meet โ including, on the years in our pool, most of the 1993 to 1995 cars. The headline difference from the M20 is that the cams are chain-driven: there is no belt, no belt interval, and no interference catastrophe waiting on an undated invoice. The chain and its guides are long-lived, and a rattling chain on a high-mileage M50 is a wear item to price, not a walk-away.
The M50's discipline is the cooling system, and it is plastic. The radiator's side tanks and hose necks are plastic that embrittles with heat cycles until a neck snaps off and dumps the coolant in seconds; the thermostat housing and expansion tank are plastic for the same reason; and early water pumps carried a plastic impeller that could disintegrate. An M50 that has overheated is as suspect as an M20 that has overheated โ warped heads and failed head gaskets follow โ so on any E36, ask when the radiator, water pump, thermostat and expansion tank were last replaced, and treat "never" on a thirty-year-old car as a $600โ1,100 cooling-system refresh that is already overdue and belongs in your offer. Metal-impeller pumps and aluminium thermostat housings are the standard upgrades and their presence in a history file is a good sign about the previous owner.
VANOS is the other M50 conversation. The seals inside the unit harden with age, and the symptoms are lost low-down torque, a rough or dipping idle, and on worn units a rattling, diesel-like noise from the front of the engine at around 2,000 rpm as the system hunts. A VANOS seal and rattle repair is roughly $500โ900 all-in at a specialist, so a rattly E36 is negotiable, not doomed. The M50 also leaks oil from the valve cover and oil filter housing gaskets, drinks a little oil at high mileage without it meaning disaster, and suffers the same vacuum-leak logic as every BMW of the era: cracked intake boots and split hoses make it idle badly long before anything electronic fails.
Gearboxes
Most of the manual 325is in our pool โ and 14 of the 20 cars are manuals โ use a five-speed Getrag gearbox: the Getrag 260 in the E30, and Getrag or ZF five-speeds in the E36. The Getrag 260 is one of the great manual gearboxes of the period: a precise, mechanical shift that rewards a deliberate hand and punishes a rushed one. Judge it cold, because second-gear synchromesh wear shows up as a crunch on the first few cold shifts into second and disappears when warm โ drive the car from cold or you will not catch it. The linkage wears before the box does: a sloppy, vague lever with inches of side-to-side play in gear is worn shifter bushings and a worn selector joint, a $150โ400 parts-and-labour refresh that transforms the car, and sellers routinely describe it as "the gearbox is tired" when the box itself is fine. A whine in fifth, jumping out of gear, or a crunch that persists hot is the real thing โ a rebuild or a good used box, $1,200โ2,500 fitted.
Between engine and gearbox, two rubber parts shape how every E30 feels. The flex disc โ the guibo โ on the propshaft cracks with age and gives a thump on take-up and a vibration under load; the centre support bearing beside it sags and lets the shaft drum against the tunnel. Neither is expensive โ $250โ600 for the pair fitted โ but both are underneath the car, invisible in photographs, and present on almost every unrestored example. Clutches last well and a slipping or juddering clutch on an E30 is a $700โ1,100 job including the rear main seal you should replace while you are in there.
The automatic is a ZF four-speed (4HP22) in the E30 and a five-speed automatic in the E36. It suits the convertible and the cruiser, and it is honest, durable and unexciting. Changes should be clean and prompt, with no flare between ratios and no long, thoughtful pause before reverse engages on a cold morning โ that pause is the classic first symptom of a tired box. A fluid and filter change is cheap insurance on any automatic you buy, $200โ350. In our pool six of the twenty cars are automatics, typically the convertibles and the softer-priced cars: the market pays for manuals, so an automatic has to win on condition.
The differential carries the 325is premium: most manual 325i cars run a 3.73 final drive, and the limited-slip unit โ standard on the 325is, optional elsewhere โ is identified by the tag on the cover and confirmed by the jack test in the models section. Differential whine on the overrun, backlash clunks and leaking pinion seals are the wear signs; a used limited-slip in good order is a sought-after part in its own right โ another reason sellers claim it, and another reason you verify it.
Problem areas
Everything in this section comes down to one sentence: the 325i's mechanicals are tough and its body is mortal. Engines, gearboxes and suspensions can all be rebuilt at prices you can plan for. Rust, once it is structural, costs more to put right than the finished car is worth โ and on a car whose newest E30 example is over thirty years old, rust is not a possibility to consider but a condition to measure. The E36 rots less readily and in different places, but trades some body problems for electrical and cooling-system ones. Assume every car you view has at least two of the faults below.
Rust: the map
Work the E30 in the order the water does.
Sills and jacking points. The most important check on the car. The sills are structural, they fill with road dirt and water thrown up by the front wheels, and they rot from the inside out โ the paint bubbles you can see are the last stage, not the first. Press hard along the full length of both sills with your thumbs, and pay particular attention to the jacking points at each end: the front jack point and the metal around it is a known rot spot, and a jack point that flexes, crunches or feels soft under pressure is structural rust, full stop. Cars that have lived in the salt belt โ and three of the twenty cars in our pool are in New York โ deserve double suspicion here. Fresh black underseal or a brand-new sill cover on one side only is a seller telling you where to look hardest. Proper sill repair, cut out and welded with paint, runs roughly $800โ2,000 a side; patching over rot is not a repair and should be priced as if the rust is still there, because it is.
Rear wheel arches and rear quarters. The second E30 signature. The inner arch lip traps mud against the outer skin, and rust starts at the lip and climbs the quarter panel. Run a fingertip around the inside of both rear arch lips: you are feeling for bubbling, crust and filler, and a cloth-wrapped magnet tells you how much of the arch is steel. Arch and quarter repairs with paint run $600โ1,500 a side done properly, and they recur if the inner structure is not treated at the same time. Check where the rear valance meets the quarters below the bumper too โ the valance traps water and rots at its seams.
The battery box and the boot floor. The E30's battery lives in the boot, on the right-hand side, and acid plus standing water rot the tray and the floor beneath it from the top down, invisibly, until the day the battery sits at an angle. Lift the battery out, or at minimum lift the boot carpet and the tray cover and look with a torch. The same water path โ a perished boot seal and tired rear light gaskets โ fills the spare wheel well and the two low pockets behind the rear wheels, so lift the spare and look in the corners. Boot floor repairs are $400โ1,000 depending on how far the rot has spread, and a boot that smells damp on a dry day is a boot that leaks.
Sunroof cars: drains and the roof skin. Most E30 sedans and coupes have a steel sunroof, and its four drain tubes run down the pillars and out through the sills. When the drains block or the tubes perish, the water goes into the sills and footwells instead โ which is why a sunroof car with rusty sills and wet carpets is telling one connected story, not three separate ones. Check the headlining for water stains and the sunroof panel for rust at its edges. A blocked drain is an afternoon's work; the rust it caused is not.
Front of the car: strut towers, wings and the scuttle. Open the bonnet and look at the front strut towers, particularly around the seams where the tower meets the inner wing: rust here is structural and expensive, and it hides under seam sealer and dirt. The bottoms of the front wings behind the wheels rot where mud packs in, and the scuttle below the windscreen bubbles where water sits under the seal. A bubbling windscreen surround is a screen-out repair, $500โ1,200 with paint, and it means the footwells below have been getting wet.
Floors. Lift every carpet you are allowed to lift. The floor pans rot from the inside, fed by the leaks above: windscreen seal, heater box, sunroof drains, perished door membranes. Surface rust is treatable; a floor you can flex with a thumb or see daylight through is a welding bill, and floor rust never travels alone โ it means the water paths above it have been leaking for years and the sills beside it are suspect.
The E36's map is shorter but not blank. Rust appears at the rear wheel arches, along the sill covers โ lift or peer behind the plastic covers, because they hide the metal they protect โ at the boot floor around the battery well on the right side, and at the jacking points, whose rubber pads fall out and let water and salt into the sill. The E36's more structural worry is not rust but fatigue: the rear subframe mounting points in the floor can tear on hard-driven cars, and the rear trailing arm mounting pockets crack. Both are checked from underneath, on a lift, and both are fabrication repairs priced per car. An E36 with a knocking rear end over bumps is describing its bushes first and its mounting points second, and you want to know which before you buy it.

Mechanical wear beyond the engine
The M20 and M50 engines are covered in their own section; what follows is everything bolted to them and everything they drive.
Cooling systems are a wear system, not a fit-and-forget system, on both generations. Radiators silt and their plastic tanks crack, viscous fan clutches die, thermostat housings warp, and hoses perish from the inside. On the E36 add the plastic water pump impeller and the expansion tank. A car with one new component in an otherwise original cooling system has been repaired, not maintained: the system is only as young as its oldest hose. Budget $600โ1,100 to renew an E36 system wholesale and $400โ800 for the equivalent E30 work, and treat any car that runs hot in traffic as a car with a job already scheduled.
The fuel system ages at both ends. In the E30, the in-tank pump and the external main pump grow noisy before they fail โ a loud buzz from under the rear seat is a pump announcing itself โ and the fuel tank itself rusts on cars that stand with low fuel, shedding debris that blocks filters and injectors. Fuel lines and the filler neck perish and leak; any smell of fuel around an E30 is a find-it-now item, not a monitor-it item. A car that has stood for years needs the tank drained and the system flushed before it is run regularly, because old-fuel varnish is the fastest way to turn a stored car into a non-runner.
Steering. Both generations use power-assisted rack-and-pinion steering, and it should be light, precise and free of play at the straight-ahead. E30 racks leak from their seals and split their boots, and a rack that has run dry wears quickly; a rebuilt rack fitted runs $500โ900. The power steering pump whines when its fluid is old or low, and the rubber steering coupling in the column perishes and introduces a vague, elastic feel at the wheel that owners misdiagnose as rack wear. Play at the wheel on either car is a sum of coupling, rack mounts, track rod ends and column bushes โ price the system, not one part.
Exhausts rot from the rear forwards, and a full standard system is a few hundred dollars in parts โ the manifold studs that snap when you change it are the real cost. Catalytic converters on US cars are now old enough to fail or to have been removed: check what is actually under the car, because a missing converter is an emissions-test failure in the states that test, whatever the seller says about exemptions.
Suspension, steering feel and brakes
The E30 rides on MacPherson struts in front and semi-trailing arms behind, with a rubber-mounted rear subframe. Every rubber part in that sentence is now at least thirty years old, and the way an unrestored E30 drives โ wandering, crashing over bumps, tramlining โ is almost entirely a rubber problem, not a design problem. The wear list, in the order it usually presents: front control arm ball joints and the rear control arm bushings (the "lollipop" bushes); rear trailing arm bushings; rear subframe bushes, whose failure lets the whole rear end steer the car over bumps and under power; anti-roll bar links and bushes; and dampers, which on an original car are simply finished. A full rubber refresh with dampers, done as one job with an alignment, runs roughly $1,500โ3,000 at a specialist and transforms the car โ it is the single best money you can spend on an E30, and a car with invoices for it is worth a real premium. Subframe bush failure has a second symptom: the differential mount and the boot floor above it take the strain, and cracked boot floors around the differential mount are found on hard-used cars.
The E36's multi-link rear end is more sophisticated and more expensive to refresh: more bushes, more links, and the rear trailing arm bushes whose failure produces the same passive-rear-steer feeling as the E30's subframe bushes. Front control arms are replaced as complete units when their ball joints wear. Dampers and top mounts wear on the same schedule as the E30's. Neither car's suspension faults are exotic โ they are the price of a car designed when bush replacement was a service item and now expected to last forever on the original rubber.
Brakes are discs all round on the 325i, with ABS fitted to most later E30s and standard on the E36. The parts are cheap and the failure mode is standing still: seized calipers, perished flex hoses, rusted solid lines and discs with a rust band and a lip from years of light use. A full hydraulic refresh โ calipers rebuilt or replaced, hoses, fluid, discs and pads as needed โ runs $800โ1,800 and is the standard first-year bill on a stored car. The handbrake is a small drum inside the rear disc on both generations, and a handbrake that barely holds is its own adjustment or shoe job, not a verdict on the main brakes. On the test drive, brake hard from speed twice: the car should stop straight, the pedal should stay firm and high, and any judder is a disc or a sticking caliper introducing itself.
Interior, electrics and the convertible top
The E30's cabin is simple, durable and dominated by three faults. The first is the dashboard: the padded dash top cracks, usually from the defroster vents outwards, and a crack-free E30 dash is now a genuinely valuable thing because used ones are hunted and recovering is specialist work. The second is the instrument cluster's service indicator board, whose rechargeable batteries leak and die with age, taking the temperature gauge, tachometer and service lights with them in various combinations โ a cluster with dead or lying gauges is very often this board, a $150โ350 repair with rebuilt boards available, and not the senders or the engine. Learn that before a seller uses a dead temperature gauge to explain why you cannot watch the temperature on the test drive: on an M20, the temperature gauge is the one instrument you must have working. The third is seats: the sport seats in the 325is and the standard seats both lose their bolsters and their recline mechanisms, the gas struts that hold the seat back die, and the driver's seat in a high-mileage car is a retrim conversation โ $400โ900 a pair for good used seats, more for a proper retrim.
The rest of the E30's electrics are age, not design: window regulators slow and die, the blower motor's resistor pack fails and takes the lower fan speeds with it, central locking actuators stick, and earth points corrode and produce every imaginable intermittent fault. A car where everything electrical works has been used and maintained, and that is worth more than a low mileage figure on a car where half the switchgear is dead.
The E36 modernised all of this and complicated some of it. The digital climate control unit fails through dried-out capacitors; window regulators use plastic sliders that snap; door cards delaminate as their glue dies; the headlining sags; and the blower's final-stage resistor fails and kills fan speeds. None of it is fatal, all of it is negotiable, and a stack of small electrical faults is a reliable sign of a car whose maintenance stopped at oil changes.
The convertible top, on both generations, is its own system. On the E30, judge the fabric for tears and shrinkage, the plastic rear window for cracks and fogging โ an opaque window is a replacement sewn in, $300โ700 โ and the frame for bent bows and worn joints. Early tops are manual and simple; the later power top adds a motor, linkage and microswitches, and a power top that stops halfway is an adjustment and switch problem more often than a motor problem. Check the top well and the boot for the water a leaking top lets in. On the E36 convertible the power top is more automated and more dependent on its control unit and microswitches; a top that needs "help" to cycle needs a specialist's hour, $150โ400, before anything expensive is condemned. On any convertible, put the top up and down twice, completely, and look at the car with it up: a top that does not seal at the windscreen header will drum, leak and rot the car from the inside.
How to inspect one
Allow an hour, bring a torch, a cloth-wrapped magnet and a friend to work the pedals and lights. Inspect in this order: identity first, because everything else is wasted on the wrong car, and structure before cosmetics, because cosmetics are cheap.
- Prove it is a 325i. Match the VIN on the title to the plate in the engine bay and the windscreen tag. Then apply the eta tests from the engines section: tachometer redline (past 6,500 rpm on a 325i, about 4,800 on an eta), engine code on the block pad, and the bonnet emissions label. On an E36, confirm the year: 1992 cars have the non-VANOS M50, 1993-on the M50TU.
- Cold start. Insist the engine is stone cold. It should start at once, settle to an even idle, and show no blue smoke. A warm engine on arrival is a seller hiding a cold-start fault.
- The belt question. Ask for the timing-belt invoice on any E30. No date, no invoice, no deal at full money โ price the $700โ1,200 belt service into the offer and do not rev the car hard until it is done. On an E36, ask the cooling-system question instead: radiator, pump, thermostat, expansion tank, when?
- Sills and jack points. Thumbs hard along both sills, then the four jacking points, feeling for softness, crunch and flex. Magnet along the sill bottoms and rear arch lips. Soft jack points end the inspection here.
- Boot and battery. Lift the carpet, the spare and the battery. Rot in the battery tray, water in the wheel pockets, and a damp smell in a dry week each mean the seals leak and the floor is going.
- Under the bonnet. Squeeze the intake boot looking for cracks, check the coolant for oil and the oil filler cap for mayonnaise, look at the strut towers for seam rust, and note whether the engine bay is honestly dirty or freshly washed for you.
- Underneath, if you can. Torch along the floors, the differential mount area, the fuel and brake lines, and โ on an E36 โ the rear subframe mounting points. A lift inspection before money changes hands is the best money in the whole purchase.
- Suspension by hand. Push each corner down hard and release: one bounce and settle is a live damper, a second bounce is a dead one. Rock each front wheel top-to-bottom and side-to-side for bearing and ball-joint play, and look at the rear tyres for the uneven wear that worn trailing-arm and subframe bushes cause.
- The drive. Fifteen minutes, from cold, including a highway stretch. A manual should crunch into second only when cold if its synchromesh is worn โ hot crunches are worse. Feel for the thump of a tired flex disc on take-up, listen for differential whine on the overrun, and rev a proven-belt E30 past 5,000 rpm: it should pull harder, not give up.
- Heat and brakes. Let it idle hot in traffic and watch the temperature gauge โ which must be working, because a dead gauge on an M20 car is itself a fault to price. Brake hard from speed twice: straight, firm, no judder.
- Electrics and, on a convertible, the top. Every window, the blower on all speeds, lights, washers, gauges. On a convertible, cycle the top fully twice and check the rear window, the header seal and the top well for water.
- Interior last. Sit in the driver's seat and judge the bolsters, look at the dashboard for cracks, and lift the rear seat base if you can โ water and rust hide under it. A sound original interior is the hardest thing to replace, so weight it after structure, before paint.

Values
The market figures for the cars currently listed, and the record of what has sold, sit in the market block the site builds beneath this guide and refreshes with the listings themselves. This section teaches you how to read them, because on a 325i the headline figure is the least informative number on the page.
Start with the condition spread, which on this model is the whole story. The gap between a project car and a sorted driver is wider than the gap between the cheapest and dearest variant: an undated timing belt, tired suspension rubber and early sill rust are all invisible in a headline price and all priced in thousands to put right, so two cars at the same asking figure can be several thousand apart in real cost by the end of the first year. Read every price as a starting point for the inspection findings, not as a verdict on the car.
Within the model, the premiums are consistent. Manual gearboxes out-price automatics, because the manual is the better drive and most buyers know it. The 325is package out-prices a plain coupe, provided the limited-slip differential and sport specification are genuinely present and verified, not just badged. Plastic-bumper E30s out-price the early aluminium-bumper cars in equal condition โ a fashion premium, worth paying only after the structural checks are equal too. Convertibles are season-sensitive in a way coupes are not, and the same open car is an easier purchase in autumn than in spring. E36s currently sit below comparable E30s because the market still reads them as old cars rather than classics; that is a judgement about fashion, not about the cars, and it is why the E36 is the value end of this guide.
Asking prices and achieved prices part company most on private sales, which is all of our current pool: twenty cars, every one from a Marketplace seller. Private sellers price from other asking prices, not from sales, and the cars that sit unsold are usually priced off the dearest listing the seller could find. A car listed for months at a firm figure is not evidence of value โ it is evidence of the opposite. The negotiation reality is that documented maintenance is the only thing that reliably defends an asking price: a car with a dated belt invoice, a refreshed cooling system and suspension invoices can hold its figure, and a car with none of those has no answer to an offer that prices the work in.
Finally, the project-versus-driver gap. A cheap 325i is cheap for reasons this guide has listed, and nearly all of them are body reasons. Buy the project only if you weld, or love someone who does; everyone else should pay the driver's premium and spend the first year driving.
Parts and ownership
The 325i is one of the best-supported classics you can own. BMW built the E30 in the millions and the E36 in similar numbers, the cars were sold worldwide, and the specialist trade is deep on both sides of the Atlantic. Service parts โ filters, belts, brake discs and pads, suspension bushes, dampers, water pumps, clutch kits โ are available from multiple suppliers at prices close to modern-car money, and most jobs are within reach of a competent home mechanic with a manual and a weekend.
Easy: everything in a major service, timing-belt kits, suspension rubber, brake hydraulics, exhausts in standard form, glass seals, and the relays and sensors that make up most Motronic faults. Harder and dearer: iX-specific drivetrain parts, crack-free E30 dashboards, good sport seats, limited-slip differentials in known condition, convertible top frames and power-top components, E36 subframe repair work, and quality paint โ a proper repaint costs more than most of these cars did a decade ago, which is why original paint in honest condition keeps its value. Rust repair panels for the E30's common areas โ arches, sills, valances โ are reproduced and affordable; the labour is the bill.
Running costs are modest if the car starts sorted. Expect fuel consumption in the low-to-mid twenties per gallon on the highway and under twenty around town, and an annual service any good independent BMW specialist can do. The budget line that catches new owners is the first year: catching up deferred maintenance on a running car โ belt service or cooling refresh, suspension rubber, brakes, fluids โ honestly runs $2,000โ4,000 before you improve anything, and recommissioning a car that has stood for years runs more. Buy a car in regular use over a sleeping car at the same price, every time.

Which one to buy
- The all-rounder: a late E30 325i coupe or sedan, manual. Plastic bumpers, the M20 in its best form, the deepest parts support and the strongest market to sell into. If you want one 325i to drive and enjoy, this is it.
- The driver's car: 325is. Same engine, better specification โ the limited-slip, sport seats and spoilers make it the E30 to drive hard. Verify the differential physically; the premium is for the hardware, not the badges.
- The value buy: E36 325i, manual, 1993-on for VANOS. A twin-cam, chain-driven, more modern car currently priced below the E30 because fashion has not caught up with it. Buy the one with a documented cooling-system refresh.
- The open car: E30 325i convertible. The cheapest route into classic open-top BMW ownership, and the newest E30s are convertibles. Judge the top, the rear window and the boot floor as hard as the engine.
- The specialist's car: 325iX. All-wheel drive, rare and fascinating, with iX-only parts to hunt. Buy it because you want exactly that, never as a budget substitute.
- The cruiser: any automatic convertible, E30 or E36. The automatic suits the open cars' relaxed brief, and the market's preference for manuals makes a good automatic the softest-priced way in โ provided condition, not the gearbox, set the price.
And the rule that overrides all of the above: buy the least rusty car with the most complete maintenance record, in the specification you can live with. Belts, bushes, brakes and cooling systems are all fixable at prices you can plan for. A rotten shell and an engine that turns out to be an eta are the two mistakes no budget fixes โ and both are caught by twenty minutes of the inspection in this guide.
See the 20 3 Series 325i Convertible 2D cars currently listed.
