Home / Buyer's guides / Integra GS Sedan 4D

Acura Integra GS Sedan 4D buyer's guide

Acura Integra GS Sedan 4D -- the model's own buyer's guide: variants, values and what to check.

Years listed: 1994-2001 ยท Series: Integra

Overview and history

The Integra is the car that proved a front-wheel-drive compact could be a proper driver's car, and it did it by being two cars at once. In ordinary RS, LS, SE and GS trim it is a well-built, economical Honda underneath the Acura badge โ€” easy to live with, easy to service, durable in the way early-1990s Hondas are durable. In GS-R and Type R trim the same shell becomes something else: a high-revving, limited-slip, close-ratio machine that period testers put in the company of far more expensive sports cars, and that thieves and cloners have hunted ever since. Which Integra you are looking at decides almost everything about how you inspect it, what you pay for it, and what can go wrong with the deal itself. This guide covers the name across its life, weighted honestly toward the cars that actually fill the market today.

The name arrives in the United States for 1986 as one of the two launch models of Honda's new Acura division, alongside the Legend. The first-generation car, sold from 1986 to 1989, is a three-door or five-door hatchback with pop-up headlamps and a 1.6-litre twin-cam engine โ€” a grown-up, better-trimmed answer to the CRX and Prelude idea, and a car that immediately wins comparison tests on its engine and gearbox alone. The second generation, sold from 1990 to 1993, grows up: a sleeker coupe and a four-door sedan, a 1.8-litre engine, and, for its last two years, the car that changes the name's trajectory โ€” the GS-R, carrying the first VTEC engine most American buyers could buy in an everyday car.

The third generation, sold from 1994 to 2001, is the definitive Integra and the one this guide spends most of its time on. It launches with the four round headlamps that divide opinion to this day, gains a mild facelift for 1998, and spans the widest range of any generation: the 142-horsepower LS most people bought, the 170-horsepower GS-R, and the Type R โ€” a lightened, seam-welded, hand-finished special with a 195-horsepower engine that revs past 8,000 rpm and a helical limited-slip differential. If you learn one generation properly, learn this one, because it is the generation the used market is made of.

After 2001 the story forks. In Japan the Integra continues for one more generation, but in the United States that car is sold as the Acura RSX, and the name disappears from American showrooms for two decades. It returns for 2023 as a five-door liftback on the modern Civic platform, with a turbocharged 1.5-litre engine and โ€” pointedly โ€” an available six-speed manual, and for 2024 the Type S revives the performance line with a 320-horsepower 2.0-litre turbo. Those cars are too new to be classics here, but they matter to a buyer of the older cars for one reason: the revival is a large part of why interest, and asking prices, for clean 1990s cars keep firming.

Now the honest statement of what our own pool holds. Every Integra currently in our listings is a third-generation car, built between 1994 and 2001, dominated by the everyday end of the range โ€” LS, GS and Special Edition cars, as four-door sedans and two-door hatchback coupes โ€” and the majority carry the four-speed automatic rather than the manual. There is no GS-R and no Type R in the current pool, no first- or second-generation car, and no revival car. The GS-R and Type R still get full treatment below, because you will meet them in the wider market and they carry the biggest risks โ€” but the typical Integra offered today is not the poster car. It is a thirty-year-old, non-VTEC, often automatic compact that has survived daily use, and it should be bought, inspected and priced as exactly that.

That survival is itself the point. These cars were modified in huge numbers during the sport-compact era, stolen in huge numbers for their engines and seats, and scrapped when values bottomed out. The survivors fall into three groups: honest, unmodified cars that were simply someone's reliable transport for decades; modified cars, from a set of wheels to full engine swaps of variable quality; and performance cars โ€” GS-Rs and especially Type Rs โ€” whose identity is part of the value and therefore part of the risk. Work out which group the car in front of you belongs to before you fall for the badge.

The models

Every Integra is a front-wheel-drive car with a transverse four-cylinder engine, independent suspension at both ends, and a choice, in most years, between a two-door hatchback coupe and a four-door sedan. Read the badge carefully: on an Integra the badge is a claim about the engine, and the engine is where the money is. A trim table follows, then the generations in turn.

ModelYearsEngineOutputBuiltCharacter
Integra RS / LS / GS (first generation)1986โ€“19891.6 twin-cam (D16A1)113โ€“118 hpNot published by trimThe original: light, revvy, pop-up lamps
Integra RS / LS / GS (second generation)1990โ€“19931.8 (B18A1)130โ€“140 hpNot published by trimThe grown-up car; coupe or sedan
Integra GS-R (second generation)1992โ€“19931.7 VTEC (B17A1)160 hpLow volume; exact split not publishedThe first VTEC GS-R; rare and sought
Integra RS / LS / SE / GS (third generation)1994โ€“20011.8 (B18B1)142 hpThe bulk of productionThe everyday Integra; the market's core
Integra GS-R (third generation)1994โ€“20011.8 VTEC (B18C1)170 hpNot published by trimThe sweet spot: VTEC, manual only
Integra Type R (third generation)1997โ€“1998, 2000โ€“20011.8 VTEC (B18C5)195 hp3,823 for the US in totalThe special: lightened, limited-slip, collectible
Integra (fourth generation, Japan; sold as RSX in the US)2002โ€“20062.0 i-VTEC (K20 family)160โ€“210 hp by marketNot published by trimThe fork in the story; badged RSX in America
Integra A-Spec (fifth generation)2023 onward1.5 turbo (L15 family)200 hpCurrent productionThe revival liftback; manual available
Integra Type S (fifth generation)2024 onward2.0 turbo (K20C family)320 hpCurrent productionThe modern performance flagship

Outputs are the period US figures. Treat production figures quoted for ordinary trims with suspicion โ€” Honda published totals for the name, not reliable trim splits โ€” so this table gives a build figure only where one is genuinely documented, in practice the US Type R.

The first generation (1986โ€“1989). A three-door hatchback at launch, joined by a five-door, with pop-up headlamps, a 1.6-litre twin-cam engine and a choice of manual or automatic. RS is the base car, LS the mid trim, GS the best-equipped. These are charming, light and simple, and now genuinely scarce โ€” most were used up as cheap transport decades ago. Rust and obsolete trim, not the engine, decide whether one is worth saving.

The second generation (1990โ€“1993). The body choices settle into the pattern that lasts: a two-door hatchback coupe and a four-door sedan, with a low, wide stance that still looks right. The standard engine grows to the 1.8-litre B18A1, rated 130 hp at launch and 140 hp from 1992. The headline is the 1992โ€“1993 GS-R: a coupe-only car with the 1.7-litre B17A1 VTEC engine making 160 hp and a close-ratio five-speed manual. It is the rarest mainstream Integra of all, and the one most often misrepresented โ€” a standard coupe with GS-R badges is a known sight, so the engine code and the VIN do the settling.

A 2001 Acura Integra GS Sedan 4D in Green, photographed in Rockville, MD
The last year of the classic Integra and the shape our listings actually hold: a 2001 GS four-door sedan in green. The sedan is the quiet buyer's car โ€” same B18B1 engine and running gear as the coupe, less modifier attention, and usually an easier life.

The third generation (1994โ€“2001). This is the core of the market and of this guide. The range runs RS (the base car, deleted after 1997), LS (the volume seller), Special Edition (a dressed-up LS, mainly 1995โ€“1996), GS (the better-equipped non-VTEC car from 1997, effectively succeeding the Special Edition) and GS-R. Every non-VTEC car uses the same 142-hp B18B1, so an RS, LS, SE and GS differ in equipment โ€” leather, sunroof, anti-lock brakes, wheels โ€” not in pace. Body styles are the two-door hatchback coupe and the four-door sedan throughout. The 1998 facelift brings revised bumpers, headlamp internals, wheels and trim; it is a styling refresh, not a mechanical one, so never pay a facelift premium as if it bought you a different car.

The GS-R (1994โ€“2001). The thinking driver's Integra. The B18C1 gives 170 hp and an 8,000-rpm redline, the five-speed manual is mandatory โ€” there is no automatic GS-R, so an automatic car wearing GS-R badges has already told you it is not one โ€” and the chassis gets firmer suspension, bigger brakes and a strut tower bar. It came as coupe and sedan, the sedan rarer and more discreet. A genuine GS-R is worth a clear premium over an LS; a dressed-up LS is worth LS money. The difference lives in the engine code on the block and in the VIN, and both checks take minutes.

The Type R (1997โ€“1998, 2000โ€“2001). The special, and the only Integra that is a blue-chip collectible in its own right. Coupe only. The B18C5 is a hand-finished development of the GS-R unit โ€” higher compression, hand-polished ports, a single-port intake manifold, a lighter flywheel โ€” making 195 hp. The shell is seam-welded and lightened: thinner glass, less sound deadening, no sunroof, and in 1997 no air conditioning as standard. A helical limited-slip differential, larger brakes, five-lug hubs, a bigger rear wing and sports seats complete a specification you can check piece by piece โ€” which matters, because the premium has made cloning an LS into a visual Type R a small industry. Championship White defines the 1997โ€“1998 cars; black and yellow join for 2000โ€“2001. Every claim a seller makes about a Type R is testable, and the inspection section gives you the tests.

A 2000 Acura Integra LS Hatchback 2D in Grey, photographed in Chatsworth, GA
The volume car in its volume form: a 2000 LS two-door hatchback in grey. This is the B18B1 car most buyers will actually meet โ€” judge it on shell condition, service history and originality, not on the performance models it shares a name with.

The fork and the revival (2002 onward). The fourth-generation car is an Integra in Japan and an RSX in the United States, so search both names or you will miss the cars. It moves to the 2.0-litre K-series engine and, in Type S form, offers 200 hp and a six-speed manual. The fifth-generation car revives the name in America for 2023 as a Civic-based liftback: a 200-hp turbocharged 1.5, a continuously variable transmission as standard and a six-speed manual with limited-slip differential as the enthusiast option, followed by the 320-hp Type S for 2024. These are modern used cars, not classics; they appear here for completeness, and because their arrival changed the temperature of the market for the 1990s cars.

One naming trap is worth stating plainly. Honda sold its own Integra in Japan alongside the Acura car, with overlapping but not identical specifications, and right-hand-drive Japanese-market cars reach the US through import. Such a car is not a fake โ€” but it is a different specification with different paperwork, and it should be priced and checked as what it is, with the steering wheel's position as your first tell.

Engines and gearboxes

Four engine families carry the whole story, and they share a Honda pattern: an aluminium block and head, a timing belt rather than a chain on the classic cars, a distributor on the B-series cars, and a service life measured in hundreds of thousands of miles if โ€” the only if that matters โ€” the belt, the oil and the valve clearances have been kept up. Learn each family by its code, because the code is stamped on the block and is the most useful identity tool you own: on B-series cars it sits on a flat pad at the front of the block, beside the gearbox, legible once you wipe the grime off. If the code on the pad does not match the badge on the tailgate, believe the pad.

The early cars: D16A1 and B18A1

The first-generation car's 1.6-litre D16A1 is a twin-cam engine from Honda's D family, making 113 hp in its first years and 118 hp from 1988. It likes revs, tolerates them, and asks for a timing belt on schedule and valve clearances checked as the miles climb. Engine parts remain findable because the D family was built in enormous numbers; generation-specific trim, lamps and panels are the real scarcity.

The second generation moves to the 1.8-litre B18A1, the first B-series engine: a twin-cam, non-VTEC unit making 130 hp at launch and 140 hp from 1992, with the broad, unstressed delivery that makes these cars such easy daily drivers. It also establishes the B-series service rhythm: belt and water pump renewed together โ€” the pump is driven by the belt, so doing one without the other is false economy โ€” a distributor whose internals age, and valve clearances adjusted as a scheduled item, not a repair. Budget roughly $600โ€“1,100 for belt, tensioner and pump done properly, and treat a car with no evidence of the job as needing it immediately.

The third-generation workhorse: B18B1

The B18B1 is the engine in the great majority of Integras you will ever look at, including every ordinary car in our current listings. It is a 1.8-litre twin-cam, non-VTEC engine making 142 hp and 127 lb-ft of torque, and its character is honest rather than exciting: strong from low revs, smooth in the middle, out of ideas sooner than the VTEC cars at the top end. That is not a criticism. For a car you intend to drive rather than polish, the B18B1 is arguably the best engine in the range โ€” the least stressed, the cheapest to service, and the one with the deepest parts pool behind it.

Mechanically it asks for the same three things as every B-series. First, the timing belt: the B18B1 is an interference engine, so a broken belt means pistons meet valves and a service item becomes a rebuild, realistically $1,800โ€“3,500. The interval is around 90,000 miles or seven years, and the second half of that sentence is the one that bites โ€” a 60,000-mile car on its original belt is overdue by age, not safe by mileage. Second, valve clearances: adjustment is mechanical, a neglected engine ticks when clearances open or โ€” more dangerously, because it is quiet โ€” burns valves when they close up. A check is roughly $200โ€“400 with a rocker-cover gasket set, and a documented recent one is a genuinely good sign. Third, oil: a quart between services on a high-mileage car, past stem and cam-end seals, is normal โ€” what matters is whether the level was kept up, so read the dipstick before you start the engine and treat a low, black reading as a summary of the car's whole maintenance life.

The supporting cast gives the trouble you will actually meet. The distributor carries the coil and igniter inside it, and heat cycles kill both โ€” the classic failure is an engine that cuts out hot and restarts when cool, covered in the problem areas section. The main relay fails the same way: its solder joints crack with heat and age. The radiator's plastic end tanks go brittle and weep. None is expensive โ€” a quality distributor runs roughly $200โ€“450, a main relay $40โ€“90 โ€” but together they are the difference between a car that starts every morning and one that strands you twice a summer.

A 1995 Acura Integra Special Edition Coupe 2D in White, photographed in Lugoff, SC
The Special Edition coupe in white: a dressed-up LS, which means the B18B1 engine and running gear of the standard car under extra equipment. On any Special Edition, GS or LS, your money is buying shell condition and history โ€” the mechanical specification is the same across all three.

The VTEC cars: B17A1, B18C1 and B18C5

VTEC โ€” Variable Valve Timing and Lift Electronic Control โ€” is Honda's system for giving one engine two characters. Below engagement, a mild cam profile delivers economy and manners; at engagement, locking pins join the cam followers to a high-lift, long-duration central lobe, and the engine's breathing, note and appetite for revs all change at once. On the GS-R's B18C1 the change comes at about 4,400 rpm, with a second event at about 5,750 rpm when the intake manifold's secondary butterflies open โ€” so a healthy GS-R has two distinct steps in its delivery, and feeling for both is a real test on a test drive, not a ritual. On the Type R's B18C5, engagement is at about 5,700 rpm through a single-port manifold, so there is one step, later and sharper.

The B17A1 in the 1992โ€“1993 GS-R is where it starts: 160 hp, built for only two years, now the hardest mainstream Integra engine to find unmodified. The B18C1 that follows it makes 170 hp and 128 lb-ft, revs to an 8,000-rpm redline, and is the engine most buyers picture when they picture a performance Integra. It needs what the B18B1 needs, plus one thing more: VTEC depends on oil pressure, oil level and a functioning solenoid and pressure switch. A GS-R that feels flat above 5,000 rpm is very often simply low on oil, because the system will not engage cleanly on a starved engine; one that never engages has an electrical or solenoid fault to find before anyone condemns the engine. Check the oil first. It is free, and it settles the question more often than any other test.

The B18C5 in the Type R is a different order of thing: 195 hp from 1.8 litres, 10.6 to 1 compression, hand-polished ports, stronger internals and an 8,400-rpm redline. It also has known appetites. Type Rs use oil at high revs by design and by age โ€” a quart in a thousand hard miles is within the range owners report on healthy engines โ€” so the question is not whether it uses oil but whether the owner knows and tops it up; a Type R run low is a Type R with worn bearings in its future. Any B18C5 that smokes blue under load, knocks under load or shows glitter in the oil is an engine-out conversation at $4,000โ€“8,000 for a proper rebuild.

Swaps are the shadow over this whole section. B-series engines interchange readily โ€” the joy of owning one and the trap in buying one โ€” and B18B1, B18C1, B18C5 and the related B16 and B20 units move between Integras and Civics with well-understood parts. A swapped car can be excellent, or a wiring and title tangle. The rule is simple: the block code tells you which engine is fitted, the VIN tells you which engine the car was born with, and where they differ you are buying a modified car and you price it as one, however well the work was done.

The modern cars: K-series roots and the turbo revival

For completeness: the fourth-generation car sold in America as the RSX uses the chain-driven 2.0-litre K20 family, making 160 hp in base form and 200 to 210 hp in Type S form, and the revived fifth-generation Integra uses a turbocharged 1.5-litre engine making 200 hp, and the 2.0-litre turbocharged K20C family engine making 320 hp in the Type S. These are modern engines with modern service regimes; the classic-car checks in this guide โ€” belts, distributors, relays โ€” do not apply to them. The discipline does: verify identity, read the history, buy condition over claims.

Gearboxes

The classic Integra offers two gearboxes, and the choice between them defines the car more than the trim level does. The five-speed manual is the one the car was designed around: light, precise, the class benchmark when new. GS-R and Type R manuals are close-ratio units that keep the VTEC engines on the cam, and the Type R adds a helical limited-slip differential as standard โ€” the GS-R does not have one, another check that separates a genuine Type R specification from a lookalike. Trouble concentrates in the synchromesh, above all on third gear, and in tired linkage bushes; both are covered in the problem areas section. A rebuild with synchros and bearings runs roughly $1,200โ€“2,500, less if the box is already out for a clutch โ€” itself a $700โ€“1,200 job fitted, and the natural moment to do both.

The four-speed automatic is the gearbox in the majority of cars in our current listings, and it deserves a fair hearing. It is a Honda-designed parallel-shaft automatic that behaves, in essence, like an automated manual, and in good order it shifts cleanly and lasts well. Its enemies are heat and neglected fluid: these boxes want their own specified fluid, changed on schedule, and one that flares between gears, shudders on engagement or delays selecting drive or reverse when cold is telling you the fluid story was skipped or the box is worn. A fluid service is cheap insurance at roughly $120โ€“250; a rebuild is $1,800โ€“3,200, a large fraction of an ordinary car's whole value โ€” so on an automatic, the gearbox test is worth as much as the engine test.

Two gearbox identity rules close the section. First, there is no automatic GS-R and no automatic Type R: both are manual-only, in every year, without exception โ€” so the gearbox is itself an identity check. Second, manual swaps into automatic shells are common and often well done, but they involve the pedal box, wiring, engine management and cluster as well as the box, and a swapped car should come with receipts covering all of it, not just a lever where the selector used to be.

Problem areas

An Integra rarely fails in an interesting way. The engines are strong, the suspension conventional, the electrics simple by modern standards โ€” so what kills these cars is a short, predictable list: rust in the rear body, a timing belt that was never changed, a distributor or relay that dies of old age, abused synchromesh, water that got in and stayed in, and, on the performance cars, a history of theft, cloning or an undocumented swap. Work through the systems in this order and you will find the expensive problems before the cheap ones distract you. Note what this section does not rest on: our current listings pool is small and carries no examined-photo aggregate for this model, so nothing here is dressed up as a statistic. This is the model's known behaviour across three decades, stated so you can test for it car by car.

Rust, body and water

An Integra does not rust like a 1960s car โ€” the steel was galvanised and the factory protection was good โ€” but it is now thirty years old, and rust follows a map you can learn. Start at the rear wheel arches. The arch lip traps mud against the inner panel, the seam holds moisture, and bubbling at the rear arch โ€” worst just behind the door on coupes, and at the arch's rear edge โ€” is the most common body fault on a third-generation car. Press and tap along the whole lip: paint over filler feels and sounds different from paint over steel, and a cloth-wrapped magnet tells you where the filler is. Arch repair done properly means cutting out and welding, roughly $800โ€“1,800 a side with paint; a car with both arches, both sills and a hatch floor gone is a shell project, not a driver, whatever the engine sounds like.

Work forward and down. The sills rot at their rear ends, where road grit blasts the coating off, and at the jacking points. The front subframe and its mounts corrode on salted-road cars, and the radiator support panel โ€” thin, low and first in line for parking knocks as well as rust โ€” is often bent or replaced; a support that does not match the bay's paint and fasteners is an accident-history question, not just a rust one. Underneath, brake and fuel lines corrode on northern cars and deserve a torch-lit look along their full run; a line replacement is a few hundred dollars, but a line that fails on the drive home is a safety verdict, not a budget line.

Water deserves its own paragraph because on an Integra water is a diagnostic tool. The sunroof drains block and overflow into the headlining and down the pillars. The tail-lamp gaskets perish and let water into the boot or hatch floor, where it sits under the spare wheel and rots the well from inside โ€” lift the spare on every car, without exception. The hatch and boot seals harden, and the result is always the same: wet carpets, misted glass, corroded connectors and a musty smell. Damp in an Integra is never just damp. It is a leak with a source, rust with a head start, and electrics with a future fault โ€” find the source or price the search.

Accident history reads the same way as on any unibody car, only more so, because so many were driven hard by young owners. Panel gaps that wander, a wing or door in a fractionally different shade, overspray on rubbers, non-original fasteners along one side of the bay, a replaced radiator support โ€” each is a question, and two together are an answer. Modifier-era cars add their own tells: holes in the inner wings for induction kits, cut wiring for alarms and amplifiers, turrets marked by strut braces, arches rolled for wider tyres. None of it is automatically a rejection. All of it is a reason the car should be cheaper than the unmodified survivor beside it.

Engine and gearbox faults

Start with the fault that ends engines. The timing belt on every B-series engine is a service item with an interval of around 90,000 miles or seven years, and the engine is an interference design: a broken belt means bent valves, and bent valves mean the head comes off. No external test tells you a belt is about to fail โ€” belts that look fine snap โ€” so the only evidence that counts is a dated invoice or a belt you change yourself. Treat every car without belt evidence as needing the job, at roughly $600โ€“1,100 with the water pump and tensioner, and a seller who says the belt was done but can show you nothing as a seller whose belt was not done. That single rule will save you more money than any other sentence in this guide.

Next, the distributor family of faults, which account for most no-start and cutting-out complaints. The distributor houses the coil and the igniter, and both die of heat and age. The classic presentation is an engine that runs perfectly cold, cuts out when fully warm โ€” often at a junction, after twenty to forty minutes โ€” and restarts once cool. The companion fault is the main relay under the dashboard: its solder joints crack, the fuel pump loses its feed after a hot soak, and the car cranks without starting until it cools. The separating test is to check for spark and fuel separately while the fault is present: no fuel-pump prime on turning the key points at the relay circuit; fuel but no spark points at the distributor. Both are cheap โ€” roughly $40โ€“90 for a relay, $200โ€“450 for a quality distributor โ€” and the trap is the cheap no-name distributor, whose igniters fail young; buy quality here or buy twice.

Oil leaks on a B-series are a geography lesson rather than a crisis. The cam-end seal and distributor O-ring weep, the rocker-cover gasket and its spark-plug tube seals harden and let oil into the plug wells โ€” pull a plug lead and look โ€” and the sump gasket and crank seals mist with age. Each is a small job, $100โ€“350 in most cases. Oil consumption is the more serious question: worn stem seals puff blue on start-up and on the overrun, while smoke under hard acceleration points to rings and bores, which is a rebuild conversation. A B-series that knocks under load, even faintly, is not a negotiation point. It is a walk-away, or a price that assumes an engine swap.

The automatic fails by neglect rather than by design. A box filled with generic fluid or never serviced shudders as the converter clutch engages, flares between second and third, and delays engaging drive or reverse from cold. Test it stone cold if you can, because a warm box hides all three. A fluid service sometimes rescues a shuddering box at $120โ€“250; a box that flares badly or will not engage cold is a rebuild at $1,800โ€“3,200, which on an LS or GS can exceed the car's worth โ€” so the automatic test is go-or-no-go, not a haggling chip. The manual fails at the other end of the scale: it gets abused. Third-gear synchromesh goes first โ€” a crunch or balk on a fast change into third, either way, is the classic sign โ€” followed by second. A synchro that only complains cold and rushed is livable; a box that crunches every change, jumps out of gear or whines throughout is a $1,200โ€“2,500 rebuild. Worn linkage bushes, by contrast, are a $50โ€“150 fix that makes the shift sloppy with nothing wrong inside the box โ€” learn to tell sloppiness, which is bushes, from crunching, which is synchros, because sellers price them the same and they are not the same.

Constant-velocity joints click on full lock once their boots have split and the grease has gone; boots caught early are $150โ€“300 a side fitted, against $250โ€“450 for a complete shaft once the joint is noisy. The exhaust manifold cracks on high-mileage cars and ticks when cold, quietening as it expands โ€” an annoyance, not a catastrophe. The radiator's plastic tanks weep at the seam; a radiator is $150โ€“350 in parts, but a car that has overheated because of it needs its head gasket questioned, and a chemical block test or cooling-system pressure test is the only honest way to answer.

A 1998 Acura Integra GS Hatchback 2D in Silver, photographed in Woodbridge, VA
The facelift car: a 1998 GS hatchback in silver, the first year of the revised lamps and bumpers. The facelift changes the face, not the faults โ€” rear arches, belt evidence and the cold automatic test matter exactly as much on this car as on a 1994.

Chassis, brakes and steering

The double-wishbone suspension โ€” fitted at both ends on the classic cars, a sophistication Honda later dropped from the Civic line โ€” wears in predictable places. Front upper ball joints and lower-arm compliance bushes go first, giving knocks over bumps and vagueness under braking; rear trailing-arm bushes split and let the rear end steer itself slightly over mid-corner bumps, a nervousness the front end gets blamed for. Bushes and joints are ordinary money โ€” a corner refreshed for $200โ€“500 โ€” and documented suspension work is a selling point worth crediting. Dampers tire by 100,000 miles, and plenty of cars ride on lowering springs of unknown origin over dampers that cannot control them; a car that crashes over bumps, sits unevenly or wears its tyres on one edge needs alignment and hardware money both.

Brakes are discs all round on most trims, and the faults are the faults of age: calipers seize โ€” the rears, whose handbrake mechanism is built into the caliper, first and worst โ€” hoses perish, and discs lip and corrode on cars that sit. A full refresh with rebuilt calipers, hoses, discs and pads runs roughly $600โ€“1,200; budget it on any car that has stood. A lit ABS lamp is often a wheel-speed sensor or its corroded connector rather than the modulator โ€” read the code before pricing the expensive part, because the sensor is a $60โ€“150 part.

Steering is hydraulic power assistance, and the rack leaks from its seals and gaiters with age while the pump whines when its fluid is old or low. Play shows as a dead patch at the straight-ahead; a reconditioned rack at $400โ€“800 fitted settles most of it. Wheels and tyres deserve an eye out of proportion to their cost: many cars wear oversized wheels or four different budget tyres, and a car on its correct wheel size with four matching, in-date tyres is a car whose owner understood it. Check the date codes as well as the tread โ€” old, hard tyres on a light, front-driven car make wet roundabouts an education you do not want.

Electrics, interior and the theft problem

The electrics are simple, and their faults are those of connectors, earths and thirty-year-old solder rather than of design. The electric aerial mast bends and strips its drive; window regulators slow and then fail, the driver's first because it has done the work; locking actuators tire; the blower's resistor pack fails one speed at a time, so a blower that only works on full speed has told you its fault in one sentence. Cluster bulbs and the clock die, and the air-conditioning โ€” a genuinely important option in the southern states where so many of these cars live โ€” loses its gas through tired O-rings and a corroded condenser; a re-gas that lasts a week is a leak, not bad luck, and a condenser and receiver-drier with a proper vacuum and recharge runs roughly $400โ€“800.

Inside, the materials last better than most contemporaries, which is why interior condition is such a good witness. The dashboard suffers in southern sun; the driver's seat bolster wears through on cloth and splits on leather; the leather itself, on GS and Special Edition cars, dries and cracks if never fed. A sunroof that tilts but will not slide is usually drains and seals rather than the motor. What you are really reading is coherence: a worn driver's seat, a shiny wheel rim and a worn gear knob that all agree with the odometer mark an honest high-mileage car, while a low odometer beside a worn-out cabin is a question that needs an answer in paperwork, not in patter.

Theft is a problem area on this model in a way it is not on most cars in this programme. Integras โ€” above all the GS-R and Type R, but LS cars too, as donors and as parts โ€” were among the most stolen cars in America in their era, because the engines, gearboxes, seats and five-lug running gear all fit the enormous Civic tuning scene. The consequences are threefold. First, a performance Integra may have a theft or salvage past: run the VIN through the title and history checks available to you, and treat a rebuilt or salvage title as a permanent discount. Second, the parts on the car may not be the parts it was born with โ€” a Type R may have lost its original engine, seats or wheels to theft and gained ordinary parts, which strips the very specification its price rests on. Third, cloning exists: a stolen car's identity transferred onto a shell, or a lesser shell dressed and documented as a Type R. The defences are physical and they are in the next section: VIN plates and stampings that agree with each other and the title, an engine code that matches the model, and the model-specific hardware โ€” five-lug hubs, limited-slip behaviour, seam welding, no sunroof on a Type R โ€” all present together. A real car passes all the checks at once. A clone usually fails two.

A 1999 Acura Integra GS Hatchback 2D in Red, photographed in Davenport, FL
A 1999 GS hatchback in red, the better-equipped non-VTEC car. Red over a Florida life makes two checks non-negotiable on a car like this: sun damage inside the cabin, and air-conditioning that blows cold at idle in traffic, not just on the move.

How to inspect one

Allow an hour, insist on a cold engine, and bring a torch, a cloth-wrapped magnet and your phone for photographs of every plate and stamping you check. Work in this order: identity first, because no mechanical virtue redeems a car that is not what it claims to be; shell second, because rust is the bill you cannot plan your way out of; mechanicals third; the road test last.

  1. Paperwork and VIN first. Match the VIN on the title to the plate at the base of the windscreen and the stamping on the firewall, character by character. On a US third-generation car the VIN itself testifies: a GS-R carries a different model code within the VIN from an LS, and a Type R has its own code again โ€” decode it before you travel, and walk away from any car whose plates disagree with each other or the title. Check the title brand while you are there: clean, rebuilt and salvage are three different prices.
  2. The engine code. Wipe the flat pad on the front of the block, beside the gearbox, and read the stamp. B18B1 means a non-VTEC car, B18C1 a GS-R, B18C5 a Type R. If the pad and the badge disagree, the pad is right and the price follows the pad. Photograph it โ€” you will want the evidence either way.
  3. The gearbox as identity. There is no automatic GS-R and no automatic Type R. An automatic car badged as either is a lesser car in costume, and a manual conversion in an automatic shell should come with receipts for the whole conversion, not just a lever.
  4. Cold start. The engine should be stone cold โ€” feel the exhaust manifold if you doubt it. A healthy B-series starts at once, idles evenly, and does not smoke. Blue smoke at start-up points to stem seals; smoke that continues under load points deeper. Listen for a rattle that lasts beyond the first second, and for the cold tick of a cracked manifold, which is minor, so you can file it correctly.
  5. The belt question. Ask for the timing belt invoice and read the date and mileage yourself. No invoice means you budget the belt, tensioner and water pump immediately, as set out in the problem areas section. Check the coolant while you are there: clean and coloured is right; rusty, oily or plain water is a cooling-system story you will pay to finish.
  6. The dipstick and the filler cap. Read the oil level before you start the engine โ€” low oil on a VTEC car is both a maintenance verdict and the first suspect if VTEC misbehaves later. Slight mayonnaise traces on the cap can be condensation on a short-trip car; thick emulsion with coolant loss is a head-gasket test, not a haggle.
  7. Rust, in the map's order. Rear arches first, with the magnet and your fingertips along the whole lip; then sill ends and jacking points; then under the car with the torch โ€” subframe mounts, floor seams, brake and fuel lines. Perforation at the arches or sills is welding money; perforation in the subframe mounts is structural. This step decides whether the inspection continues.
  8. The spare-wheel well and the carpets. Lift the spare and look for water, staining and rust in the well โ€” the tail-lamp gasket test from the problem areas section. Then feel every carpet, front and rear. Damp means a leak with a source; find it or price the search.
  9. The warm-up faults. Let the car idle to full temperature and leave it there while you work the electrics. You are waiting for the fan cycling as it should, and for the distributor and main-relay faults that only appear hot. Work every window, the sunroof if fitted, the blower on every speed, the lights, the washers and the air-conditioning โ€” cold at idle, not just at speed.
  10. The automatic test, cold if you can. Engage drive and reverse from cold and time it: a long delay or a thump is the box telling you its history. On the road, feel for flare between gears and shudder as the converter clutch engages. Any of the three, badly, ends the negotiation or reprices the car by a rebuild.
  11. The test drive, manual car. Fifteen minutes, with third gear worked hard in both directions, listening and feeling for the synchro crunch described in the problem areas. Then find the VTEC change on a VTEC car โ€” one step on a Type R, two on a GS-R โ€” and confirm it arrives cleanly, every time, with the engine warm and the oil right.
  12. Brakes, steering and stance. Brake firmly from speed: the car should stop straight, without judder or a dragging caliper's pull. At parking speed, turn lock to lock and listen for joint clicking. Finally, stand back: level stance, even arch gaps, straight reflections down each flank. Then sit in the driver's seat and ask whether its wear, the wheel's shine and the odometer all tell the same story. If they do, and the car has passed steps 1 to 11, you are looking at an honest Integra โ€” buy it on condition.

Values

The build of this page carries the live market beneath this guide โ€” the cars listed now and the recorded sales โ€” and that block, refreshed as the market moves, is where the numbers live. This section teaches you how to read them, because on an Integra the spread between the cheapest and dearest car wearing the same badge is wider than on almost any other model here, and the badge explains less of it than you would expect.

Start with the hierarchy, which is stable even as the figures move. The Type R sits in a market of its own, priced as a collectible rather than a used car, and within it originality is the currency: a matching, documented, unmodified car and a modified or identity-clouded car are effectively two different models sharing a name. The GS-R sits a clear step below, priced as an enthusiast's car, with the sedan generally the softer-priced, better-value route to the same engine. The non-VTEC cars โ€” LS, GS, Special Edition โ€” form the volume market, where trim differences are worth very little and condition almost everything. A superb GS is worth more than a tired GS-R to anyone who intends to drive the car, whatever the badge hierarchy says.

Within any trim, four things move the price. The first is the shell: rust-free rear arches and sills are genuinely scarce, and worth more than any bolt-on part because they cannot be bought and fitted in an afternoon. The second is evidence โ€” a belt invoice, a valve-clearance record, fluid changes for an automatic โ€” because evidence converts known risks into known costs. The third is originality: unmodified cars, on correct wheels, with their original engine and an unworn interior, are the minority of survivors and the market knows it. The fourth is the gearbox: the manual prices as the enthusiast's choice in the performance trims, while in the ordinary trims an automatic with a clean cold-shift test is no disgrace and often the better-kept car.

Read asking prices against achieved prices with particular care on this model. The modifier era left a long tail of cars advertised by their parts lists, and a sum-of-parts asking price is a hope, not a valuation โ€” modifications narrow the pool of buyers even when expensively done, and the market pays for them at a steep discount to cost, if at all. Theft and salvage history cuts the same way, permanently: a rebuilt-title car is one to buy cheaply and keep, not a bargain route to a profit. Project cars price by the shell and the engine code alone, because everything else on a project is a bill. And allow for the revival effect: the modern Integra firms the top of the classic market โ€” the best Type Rs and GS-Rs โ€” far more than it firms a tired automatic LS. Buy the car in front of you at the level of its own trim and condition.

Parts and ownership

The Integra is one of the easiest classics of its era to keep, for one structural reason: it shares its mechanical life with the Civic family and with one of the largest tuning aftermarkets any car has ever had. Between Honda's own parts operation, the pattern-parts trade and the performance industry, very little on a third-generation car is truly unobtainable โ€” the skill is knowing which source to use for which part, because the cheapest version of a Honda part is not always the one that lasts.

Easy: service items, filters, plugs, belts, brake discs, pads and calipers, suspension bushes and joints, dampers, exhausts, radiators, alternators, starter motors and clutch kits. The B-series is supported to a degree most classic engines never approach: gaskets, seals, bearings, water pumps and timing components are all ordinary stock, and a competent independent Honda specialist โ€” who will have seen every fault in this guide before โ€” beats a generalist, at ordinary labour rates. A routine service runs roughly $150โ€“300, and the belt service, at $600โ€“1,100 with the pump, is the largest scheduled bill the car presents.

Harder and dearer: trim and body. Interior plastics, seat fabrics in the correct patterns, glass, lamp units for facelift and pre-facelift cars, and rust-free panels age out of the system first, and clean used stock is the market you shop in. Performance hardware carries its own premium: Type R seats, five-lug hubs, the limited-slip gearbox and B18C5 components are hunted by the Civic tuning world as well as by Integra owners, so they price like collectibles because they are. Distributor quality is the standing trap โ€” the market is full of cheap units with short-lived igniters, and a quality part at $200โ€“450 is the economical buy over a cheap one bought twice.

Running costs. Fuel consumption is modest by any classic standard โ€” light cars, small efficient engines. Insurance follows the model's theft history rather than its performance, so shop around; a modern immobiliser and, on a GS-R or Type R, agreed-value cover with the identity photographs on file are part of the cost of owning the car, not extras. The first-year budget rule applies with full force: catching up a neglected car's belt, fluids, brakes and tyres honestly costs $1,500โ€“3,500 before you improve anything, and a car in regular use with that work evidenced is worth a premium over a stored car every time. Buy the used one, not the asleep one โ€” an Integra driven weekly is one whose relays, seals and calipers all still work.

Which one to buy

And the rule that overrides all of the above: buy the car whose identity, shell and paperwork all agree, in the specification you can live with. Engines can be rebuilt, synchros renewed and distributors replaced at prices you can plan for. A rotten shell, a clouded title or a badge the engine code will not support are the three things no budget fixes โ€” and the three things this market is best at hiding.

See the 14 Integra GS Sedan 4D cars currently listed.